Table of Contents
Advertisement
Quick Links
DIE GRINDER
STOCK No.57842
PART No.DG528
110V
57843
230V
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE
THE SAFE AND EFFECTIVE USE OF THIS TOOL.
08/99
GENERAL INFORMATION
This manual has been compiled by Draper Tools and is an integrated part of the power tool
equipment, which should be kept with the machine.
This manual describes the purpose for which this tool has been designed and contains all the
necessary information to ensure its correct and safe use.We recommend that this manual is read
before any operation of the machine, before performing any kind of adjustment to the machine, and
prior to any maintenance tasks. By following all the general safety instructions contained in this
manual, it will ensure both machine and operator safety, together with longer life of the tool itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the
operation of the machine.
Whilst every effort has been made to ensure accuracy of information contained in this manual, the
Draper Tool policy of continuous improvement determines the right to make modifications without
prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper DG528
Summary of Contents for Draper DG528
- Page 1 08/99 GENERAL INFORMATION This manual has been compiled by Draper Tools and is an integrated part of the power tool equipment, which should be kept with the machine. This manual describes the purpose for which this tool has been designed and contains all the necessary information to ensure its correct and safe use.We recommend that this manual is read...
-
Page 2: Table Of Contents
Operation & Use ....................6 General information ..................6 Maintenance/parts/replacement..............7 Optional Accessories ..................8 DECLARATION OF CONFORMITY Draper Tools Ltd. Hursley Road, Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF. England. Declare under our sole responsibility that the product: Stock Number:- 57842 & 57843. Part Number:- DG528. -
Page 3: Specification & Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you produce a dated receipt or invoice to verify your proof of purchase within the 12 month period. -
Page 4: Power Supply
(i.e. red). Fuse covers are available from your Draper Tools stockist. If the fitted plug is not suitable, it should be cut off and destroyed. *The end of the cable should now be suitably prepared and the correct type of plug fitted. -
Page 5: General Safety Instructions
IMPORTANT Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. -
Page 6: Know Your Die Grinder
GETTING TO KNOW YOUR DIE GRINDER ✗✌ ✖✌ ✘✌ ✙✌ ✚✌ ✕✌ ✛✌ ✜✌ 1. Draper Logo 2. Rating Plate 3. Housing/Handgrip 4. Switch 5. Head 6. Collet Shaft 7. Collet Nut 8. Spanners - 5 -... -
Page 7: Operation & Use
OPERATION & USE IMPORTANT Fig.2 Make sure that mains voltages match the voltage ✪✌ stated on the machine’s rating plate. GUARD Given the particular type of operation for which the machine will be used, it has not been fitted with a protective guard on the grinding point. -
Page 8: Maintenance/Parts/Replacement
The use of compressed air through ventilation slots. original Draper spare parts is recommended. After having fitted new brushes allow the motor to DISPOSAL run for at least five minutes without load for the At the end of the machine’s working life, or when... -
Page 9: Optional Accessories
OPTIONAL ACCESSORIES For a full range of optional accessories, please refer to your Draper catalogue. - 8 -... - Page 10 NOTES - 9 -...
- Page 11 NOTES - 10 -...
- Page 12 ©Published by Draper Tools Ltd. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the DG528 and is the answer not in the manual?
Questions and answers