Clarke Devil 6003 Operating And Maintenance Instructions Manual
Electric fan heaters
Hide thumbs
Also See for Devil 6003:
- Operating and maintenance instructions manual (20 pages) ,
- Operation & maintenance instructions manual (21 pages)
Related Manuals for Clarke Devil 6003
Summary of Contents for Clarke Devil 6003
- Page 1 ELECTRIC FAN HEATERS Devil 6003, 6005, 6009 & 6015 Part Nos: 6925220, 6925225, 6925230 & 6925235 OPERATING & MAINTENANCE INSTRUCTIONS GC0110...
-
Page 2: Introduction
INTRODUCTION Thank you for purchasing this CLARKE Electric Fan Heater. Please read this manual thoroughly and follow the instructions carefully. Before attempting to use the heater, thoroughly familiarise yourself with the heater & its operation. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to the heater giving you long and satisfactory service. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION .................. 2 GUARANTEE ..................2 ENVIRONMENTAL PROTECTION ............2 TABLE OF CONTENTS ................3 GENERAL SAFETY RULES ..............4 ELECTRICAL CONNECTIONS .............. 6 OPERATION ..................8 MAINTENANCE ................... 10 FAULT FINDING ................... 11 PARTS LISTS & DIAGRAMS ..............12 WIRING DIAGRAMS ................ -
Page 4: General Safety Rules
GENERAL SAFETY RULES WORK AREA 1. These heaters are for INDOOR USE ONLY. 2. Do not expose the heater or power cable to rain or wet conditions. Any water entering the heater will increase the risk of electric shock. DO NOT use this heater in a bathroom, shower room, in the vicinity of a swimming pool, or any wet environment. - Page 5 3. Keep the mains cable well away from machines and ensure an adequate electrical supply is close at hand so that the operation is not restricted by the length of the cable. 4. ALWAYS disconnect from the mains supply before moving the heater or performing any maintenance tasks.
-
Page 6: Electrical Connections
3. Should you wish to replace a detachable fuse carrier, ensure that the correct replacement is used (as indicated by marking or colour code). 4. Replacement fuse covers can be obtained from your local Clarke dealer or most electrical stockists. - Page 7 DEVIL 6005 (5KW), DEVIL 6009(9KW) AND DEVIL 6015(15KW) UNITS These machines MUST be connected to a 400 Volt, 3 PHASE 50Hz supply through a suitably fused isolator switch. It cannot be operated from a single phase supply. The user should purchase a suitable connecting lead as shown in the diagram, which is compatible with the appliance socket.
-
Page 8: Operation
OPERATION The Devil range of fan assisted electric heaters are suitable for household (Devil 6003 only) or workshop/factory use. They incorporate a thermostat which detects the temperature of the room air and controls the heater to maintain a pre-selected temperature between 0 & 40°C. A manually reset thermal cutout is provided for safety in the event of overheating on the 6005, 6009 &... - Page 9 When using the heater for the first time a slight emission of smoke may be noticed. This is quite normal and soon stops. It is caused by residual traces of oil remaining on the element from production. After use, turn the thermostat to the OFF position and turn the selector switch to the Fan Only position, and leave the unit to cool down for a couple of minutes.
-
Page 10: Maintenance
• Avoid using solvents when cleaning plastic parts, most plastics are susceptible to damage from various types of commercial solvents. • Refer to your CLARKE dealer if internal maintenance is required. The unit is fitted with tamper-proof screws to discourage users from dismantling the heater. -
Page 11: Fault Finding
FAULT FINDING l l u & , y l l n i l i r l n i . t i H " " s i l l l i y l l y l l . t i... -
Page 12: Parts Lists & Diagrams
PARTS DIAGRAM DEVIL 6003 e l l i t n i n i i l c l l o l l o i t a... - Page 13 PARTS DIAGRAM DEVIL 6005 e l l r t n c i t r t n l l o r t n l l o y r t i t a...
- Page 14 PARTS DIAGRAM DEVIL 6009 i t a e l l y r t l l o c i t l l o...
- Page 15 PARTS DIAGRAM DEVIL 6015 e l l r t n r t n r e l r t n r e l i t r i t a...
-
Page 16: Wiring Diagrams
WIRING DIAGRAMS 230v / 3kw T = Thermostat K1, K2 = Switch M = Motor TV = Self resetting D = Heater Tube themal cut-out 400v / 5kw 400v / 9kw T = Thermostat B = Switch M = Motor TV =Manually resetting thermal cut-out D = Heater Tube... - Page 17 WIRING DIAGRAMS 400v / 15kw T = Thermostat B = Switch M = Motor TV=Manually resetting thermal cut-out D =Heater Tube...
-
Page 18: Technical Specification
° 0 Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. For parts & Servicing, please contact your nearest dealer, or CLARKE International, on one of the following numbers. -
Page 19: Declaration Of Conformity
The CE mark was first applied in: 2007 Product Description: Electric Fan Heaters (3kW, 5kW, 9kW,15kW ) Model number(s): Devil 6003,6005,6009,6015 Serial / batch Number: Current Manufacture. Date of Issue: 02/09/2008 Signed A.C. AIKEN Senior Manager Clarke International. ELECTRIC HEATERS-TEC SPEC-DOC- RV1.doc Page 1 of 1...
Need help?
Do you have a question about the Devil 6003 and is the answer not in the manual?
Questions and answers