Related Manuals for Shure BLX4R
Summary of Contents for Shure BLX4R
- Page 1 BLX4R Wireless Microphone System Système de microphone sans fil BLX4R Sistema de micrófonos inalámbricos BLX4R Sistema de Microfone Sem Fio BLX4R ©2014 Shure Incorporated Printed in U.S.A. 27A21195 (Rev. 5)
- Page 2 IMPORTANT SAFETY INSTRUCTIONS 14. REFER all servicing to qualified service personnel. Servicing is required when the ap- paratus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been READ these instructions.
-
Page 3: Quick Start Guide
Conecte el receptor a la mezcladora o amplificador. Oprima el botón de alimentación para encender el receptor. Conecte o receptor ao mixer ou ao amplificador. Pressione o botão liga/desliga para ligar o receptor. BLX4R group channel (A-Y) (0-9) ①... - Page 4 Install batteries and turn on transmitter. Installer les piles et allumer l’émetteur. Instale las baterías y encienda el transmisor. Instale as pilhas e ligue o transmissor. group channel (A-Y) (0-9) On the transmitter, set the group and channel to match the receiver. The RF bars and battery LED on the receiver should illuminate.
- Page 5 If setting up additional systems, leave the first transmitter and receiver on. For each additional receiver, manually set the group to match the first receiver. Note: The receiver will automatically perform a channel scan to find an available fre- quency after the group has been selected. Set the transmitter frequency to match the receiver. Si l'on configure d'autres systèmes, laisser les premiers émetteur et récepteur allumés.
- Page 6 BLX4R Receiver Front Panel Rear Panel BLX4R group channel (A-Y) (0-9) ANTENNA B POWER MIC OUT INSTRUMENT OUT VOLUME ANTENNA A ① Transmitter Battery LED ⑧ Strain-relief loop for power cord ④ channel Button • Green = Runtime greater than 1 hour •...
-
Page 7: Transmitter Led Indicators
Transmitters BLX1 ① LED Indicator BLX1 Displays power and battery status (see table). ② power Switch ④ Toggles power on or off. ② ③ 4-Pin Microphone Input Jack (TA4 connector) ④ Antenna ⑤ group Button Changes group setting. ⑥ LED Display Displays group and channel setting. -
Page 8: Single System Set Up
Single System Set Up Before you begin, turn off all transmitters and turn on any equipment (other group microphones or personal monitoring systems) that could cause interference (A-Y) during the performance. 1. Press and release the group button on the receiver. The receiver scans for the clearest group and channel. -
Page 9: Multiple System Set Up
Multiple System Set Up Up to 12 systems can operate simultaneously (band and RF environment dependent). Set up each system one-at-a-time. Once a receiver and transmitter are tuned to the same group and channel, leave the transmitter powered Important: on. Otherwise, scans from the other receivers will not detect that channel as occupied. Turn any other equipment that could cause interference during the performance so it will be detected during the group and channel scans in the fol- lowing steps. -
Page 10: Tips To Improve Wireless System Performance
Tips to Improve Wireless System Performance If you encounter interference or dropouts, try the following suggestions: • Choose a different receiver channel • Remove nearby sources of wireless interference, such as cell phones, two-way radios, computers, media players, Wi-Fi devices, and digital •... -
Page 11: Locking And Unlocking Controls
Removing and Installing Identification Caps Press and hold the power button to power off the BLX2 or BLX4R. To power off the BLX1, slide the power switch to OFF. The BLX2 is equipped with a black identification cap from the factory (dual vocal systems ship with additional gray cap). -
Page 12: Troubleshooting
Rack-Mounting a Receiver Use the supplied mounting hardware to install the receiver in a standard 19" audio equipment rack. BXL4R group channel (A-Y) (0-9) SHURE INCORPORATED NILES, IL 60714 BXL4R group channel ANTENNA B POWER MIC OUT LINE OUT ANTENNA A... -
Page 13: Specifications
(with respect to pin 3 of low-impedance output) and the tip of the high 2 LR6 AA batteries, 1.5 V, alkaline impedance 1/4-inch output. Battery Life up to 14 hours (alkaline) BLX1 BLX4R Audio Input Level Output Impedance gain position -16 dBV maximum XLR connector 200 Ω... -
Page 14: Australia Warning For Wireless
: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.shure.com The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance... - Page 15 United States, Canada, Latin Asia, Pacific: Europe, Middle East, Africa: America, Caribbean: Shure Asia Limited Shure Europe GmbH Shure Incorporated 22/F, 625 King’s Road Jakob-Dieffenbacher-Str. 12, 5800 West Touhy Avenue North Point, Island East 75031 Eppingen, Germany Hong Kong Niles, IL 60714-4608 USA...