Table of Contents
Advertisement
●
Command list
●
Assign parameters on the left column at "*".
●
Make the order of commands the same as that of the button operation on the unit. The commands sent in a wrong order will be
ignored.
Function
Logging in (starting communication)
Logging off (quitting communication)
Starting operation of INPUT SELECT
Selecting an input terminal
Turning LR inversion on/off
Starting operation of OUTPUT PRESET
Selecting an SDI output type
Selecting an HDMI output type
Selecting a 3D mixing format
Starting operation of FUNCTION
Turning the rotation function on/off
Turning the frame synchronizer on/off
Turning the operation tones on/off
Adjusting the brightness of the information display
Storing settings into memory
Loading settings from memory
Starting operation of the scope function
Displaying the waveform monitor or vectorscope
Assigning an input source for a scope
Selecting a scope position
Turning the lowpass filter on/off
Adjusting the gain of the waveform monitor
Adjusting the gain of the vectorscope
Starting operation of ADJUST MODE
Selecting the display format of ADJUST MODE
Moving the dividing line of split
Adjusting parallax
Adjusting intensity
Adjusting sub-intensity
Starting operation of 2D-3D
Turning the 2D-3D converter on/off
Normal status
Abnormal status
Command
Parameter
!00BCN1000Cr
—
!00BCN0000Cr
—
!00INPUT00Cr
—
0x00: SDI-LR/0x01: SDI-1(L)
!00INPSE0*Cr
0x02: SDI-2(R)/0x03: HDMI
0x00: NORMAL/0x01: INVERT
!00BOTHP0*Cr
!00OUTPU00Cr
—
0x00: MIX/0x01: INDIVIDUAL
!00SDIMX0*Cr
0x00: MIX/0x01: INDIVIDUAL
!00HDMIM0*Cr
0x00: LINE BY LINE/0x01: SIDE BY SIDE H
!003DFOR0*Cr
0x02: ABOVE-BELOW/0x03: CHECKER BOARD
!00MMENU00Cr
—
0x00: OFF/0x01: SDI-1(L)ROTATE
!00SDIRT0*Cr
0x02: SDI-2(R)ROTATE
0x00: OFF/0x01: ON
!00FRASY0*Cr
0x00: ON/0x01: OFF
!00BEEPA0*Cr
0x00 - 0x1E: 0 - +30
!00BACKL+*Cr
0xFF - 0xE2: −1 - −30
!00BACKL−*Cr
0x00: MEMORY-1/0x01: MEMORY-2
!00MEMSV0*Cr
0x00: MEMORY-1/0x01: MEMORY-2
!00MEMLD0*Cr
!00SCOPE00Cr
—
0x00: OFF
0x01: Waveform monitor
!00SCMOD0*Cr
0x02: Vectorscope
0x00: PARA. (SDI-LR)/0x01: BAL. (SDI-LR)
!00SCSIG0*Cr
0x02: SDI-IN 1(L)/0x03: SDI-IN 2(R)
0x00: RIGHT LOWER/0x01: LEFT LOWER
!00SCPOS0*Cr
0x02: LEFT UPPER/0x03: RIGHT UPPER
0x00: OFF/0x01: ON
!00SCPFI0*Cr
0x00 - 0x1E: 0 - +30
!00SCWFG+*Cr
0xFF - 0xE2: −1 - −30
!00SCWFG−*Cr
0x00 - 0x1E: 0 - +30
!00SCVEG+*Cr
0xFF - 0xE2: −1 - −30
!00SCVEG−*Cr
!00ADJUS00Cr
—
0x00: OFF
0x01: SPLIT MODE
0x02: ANAGLYPH
0x03: LR-SEQ. MODE
0x04: PARALLAX
0x05: INTENSITY
0x06: PARALLAX ANA
!00ADJMD0*Cr
0x07: INTENSITY ANA
0x08: PARALLAX LRS
0x09: INTENSITY LRS
0x0a: SUB INT.
0x0b: SUB INT. ANA
0x0c: SUB INT. LRS
0x00 - 0x3C: 0 - +60
!00ADJOS+*Cr
0xFF - 0xC4: −1 - −60
!00ADJOS−*Cr
0x00 - 0x3C: 0 - +60
!00ADJPX0*Cr
0x00 - 0x3C: 0 - +60
!00ADJIY0*Cr
0x00 - 0x3C: 0 - +60
!00ADJSI0*Cr
!002D/3D00Cr
—
0x00: OFF/0x01: ON
!00CONVE0*Cr
@00BOK.000Cr
—
n=0: illegal command/n=1: illegal setting value
@00BNGn***Cr
n=2: unexecutable in the current mode
19
EN
Advertisement
Table of Contents
