Download Print this page

Hitachi JPEG2000 User Manual

Stand alone dvr.
Hide thumbs

Advertisement

CHAP.3 Operation
3-8 switch audio channel
CHAP.4 Set up
4-5 Bak-up
JPEG2000 Stand alone DVR User Guide
CONTENTS
............................................................................... 3
............................................................................... 3
............................................................................... 4
............................................................................... 6
............................................................................... 8
............................................................................... 9
............................................................................... 10
............................................................................... 11
............................................................................... 12
............................................................................... 14
............................................................................... 15
............................................................................... 16
............................................................................... 17
............................................................................... 17
............................................................................... 17
............................................................................... 18
............................................................................... 19
............................................................................... 19
............................................................................... 19
............................................................................... 20
............................................................................... 21
............................................................................... 24
............................................................................... 25
............................................................................... 26
............................................................................... 34
............................................................................... 37
............................................................................... 38
............................................................................... 43
............................................................................... 43
- 1 -
Date: 2006/07/05 VER: 1.5

Advertisement

   Related Manuals for Hitachi JPEG2000

   Summary of Contents for Hitachi JPEG2000

  • Page 1: Table Of Contents

    JPEG2000 Stand alone DVR User Guide Caution Package Specification CHAP.1 Appearance 1-1 Front panel introduction 1-2 Back panel introduction 1-3 IR remote controller introduction CHAP.2 Installation 2-1 Camera and monitor installation 2-2 Sensor and alarm installation 2-3 Network and serial port installation...

  • Page 2

    JPEG2000 Stand alone DVR User Guide CHAP.5 CD-R bck-up 5-1 Data backup 5-2 CD-R player software installation 5-3 CD-R player software interface CHAP.6 PTZ camera control 6-1 PTZ camera installation 6-2 PTZ camera operation CHAP.7 Network & remote software 7-1 Network configuration...

  • Page 3: Caution

    For you safety, unplug the power before moving the DVR, installing, or replacing any parts or hard drive. Make sure all the power cable and wires are properly set up before using the DVR. Contact your distributor immediately if there is any defect.

  • Page 4: Specification

    JPEG2000 Stand alone DVR User Guide Model Video Input Video I/O Video Output VGA Output Audio I/O Audio Input (Optional) Audio Output Display Resolution Monitoring Split Screen Method ZOOM IN/OUT Sequence Resolution Frame Rate Compression Record Playback Quality Storage Device...

  • Page 5

    JPEG2000 Stand alone DVR User Guide Protocol Network Remote monitoring Back-up PTZ Control RS232 Alarm Input Assistant Functions Alarm Output Remote Controller Control Device Multi-language Temperature Humidity Mechanism Dimension Weight Power TCP/IP Remote Softeware: Remote live view, playback, and save as AVI...

  • Page 6: Chap.1 Appearance

    JPEG2000 Stand alone DVR User Guide CHAP.1 Appearance 1-1 Front panel introduction 1.[CD-RW] Built-in CD-RW for CD-R back-up. 2.[IR Receiver & LED Lamps] IR Remote Controller Receiver. DVR Status LED: RUN- Flashes when play picture by picture through J. Shuttle.

  • Page 7

    JPEG2000 Stand alone DVR User Guide 10.[Control] SEQ- Full screen sequencing or the smaller screen sequencing in PIP mode. PIP- For entering the Picture in Picture mode from full screen mode. NEXT- Switch other control keys in PTZ mode. Switch to other channel in a split screen.

  • Page 8: Back Panel Introduction

    JPEG2000 Stand alone DVR User Guide 1-2 Back panel introduction [4Channel] [8Channel] [16Channel] 1.[RS485, Relay Output, Sensor Input] RS485, for direct connection to PTZ cameras. 16 sensor inputs and 1 relay output. 2.[VGA Output] Connection to a VGA monitor or TFT LCD.

  • Page 9: Ir Remote Controller Introduction

    JPEG2000 Stand alone DVR User Guide 1-3 IR remote controller introduction 1.[MENU] Enter menu or exit 2.[Split /OSD] 4S: 4 split 9S: 9 split 16S: 16 split OSD: OSD words on/off 3.[1~16 Channel] Switch channel in live or playback; password entering 4.[Control function]...

  • Page 10: Chap.2 Installation

    2-1-2 Monitor and VCR installation Monitor: Connect the MONTIOR port on the DVR back panel to the “video in” port on the monitor. VCR: Connect the VCR port on the DVR back panel to the “Video In” on the VCR.

  • Page 11: Sensor And Alarm Installation

    JPEG2000 Stand alone DVR User Guide 2-1-3 Loop out installation 2-2 Sensor and alarm installation 2-2-1 Input & Output 1.[D1~D16 Alarm Input/GND for Location] 16 Sensor inputs, for sensor input installation 2.[Relay Output NO/NC/COM] The application of relay output is NO+COM + NC+COM...

  • Page 12: Network And Serial Port Installation

    Ethernet Setup between ADSL and Cable is different. For details, please refer to Ch. 7-2 Network installation. 2-3-2 Serial port setup User is able to connect the COM port of PC or other device to the DVR through RS232. RS232 settings (baudrate/ parity/ length/ stop bit ) are NOT adjustable.

  • Page 13: Ptz Camera Installation

    JPEG2000 Stand alone DVR User Guide connector description To connect DVR to a PC, users must use a twisted RS232 cable, as the illustration. DVMR unit 2-3-3 PTZ camera installation Please connect the PTZ’s D+ to the DVR’s D+ , and D- to D-.

  • Page 14: Hdd Installation

    1. Power off the DVR before HDD installation. 2. Jumper setting must follow the instruction of HDD manufacturer. 3. Suggested HDD spec: Maxtor or Hitachi, 7200 RPM (or above), ATA-100 Maxtor, Hitachi, and Seagate if firmware version is above V1.46.

  • Page 15: Power Plugging

    JPEG2000 Stand alone DVR User Guide 2-5 Power plugging Insert the adapter to the rear power socket of DVR. Insert the power cable to the other side of adapter. Plug in the power cable and power on the DVR. Caution: Please use a 100~240VAC 50~60HZ and 12VDC 8A or 5A power supply or it may damage the DVR.

  • Page 16: Display Configuration

    JPEG2000 Stand alone DVR User Guide CHAP.3 Operation 3-1 Display configuration 1.[Time] Current system time or the recorded time in playback 2.[Date] Current system date or the recorded date in playback 3.[Camera title] Camera title of the displayed channel. Camera title can be modified in [SYSTEM MENU] [CONFIGURATION] [CAMERA SETUP] 4.[Record mode]...

  • Page 17: Screen Switch/osd Position Adjust

    JPEG2000 Stand alone DVR User Guide 3-2 Screen switch/OSD position adjust 3-3 PIP view In full screen mode, press “PIP” to enter PIP mode. Press “PIP” again to cancel. 3-4 Freeze view 3-4-1 Freeze in split mode In a split screen mode, press FREEZE and press a number button to select the corresponding channel to freeze.

  • Page 18: View In Sequence

    JPEG2000 Stand alone DVR User Guide 3-4-2 Freeze in Full mode In full screen mode, Press FREEZE to freeze the channel, and press FREEZE again to cancel. 3-5 View in sequence Press SEQ to enter Sequential Switch and press SEQ again to cancel.

  • Page 19: Zoom View

    After pressing “K. LOCK “, you’ll see LOCK on screen and no button is fucntioning at this time. To unlock, press and hold K.LOCK and enter Admin’spassword. Please note that rebooting the DVR can not deactivate K.LOCK. You must enter ADMIN’s password to unlock the keys.

  • Page 20: Record

    5.When the record schedule is set to Not Record. 6.Without clearing HDD or running factory defaults after a new HDD is installed. 7. When the DVR enters the Search dialog window. The DVR, if set to Triplex Mode, resumes recording as soon as it enters playback.

  • Page 21: Playback

    JPEG2000 Stand alone DVR User Guide 3-9 Playback 3-9-1 Play/Stop 3-9-2 Search mode 1.[SEARCH BAR] Search by appointing a recording percentage. 2.[TIME/DATE] Search by appointing a time and date 3.[EVENT LIST] Search by Event list. Press PLAY key on front panel to start playback starting from the last playback time.

  • Page 22

    JPEG2000 Stand alone DVR User Guide 3-9-3 SEARCH BAR Using +/- keys to select the recording percentage of the search bar. Press “ ENTER ”key to confirm and start the playback. 3-9-4 TIME/DATE 1.[START] The start time and date of recording It shows that the start time and date of the recording data.

  • Page 23

    JPEG2000 Stand alone DVR User Guide 3-9-6 Playback speed adjustments 3-9-7 Adjust Playback speed by IR remote controller While playback, select the direction keys of remote control to adjust the speed. X times high-speed playback. Rewind. Adjust the speed by REW key (High-speed backward playback) or FF key (High-speed forward Playback).

  • Page 24: Log-in

    Rebooting the DVR and resetting the factory defaults will not reset the password to the default. 2. Please contact your reseller if you forget the password. 3. The DVR will exit the Login screen and return to LIVE automatically if there is no action taken for 4 seconds. 4-1-2 SYSTEM MENU ※Use ▲...

  • Page 25: Display Setup

    ICON DISPLAY - Display (ON) or hide (OFF) the cue icons on the screen. DVR STATUS - Display (ON) or hide (OFF) the recording status on the screen. REC/PLAY BAR - Display (ON) or hide (OFF) the recording percentage of HDD.

  • Page 26: Configuration

    JPEG2000 Stand alone DVR User Guide 4-2-2 Monitor setup 4-3 Configuration 1.[VGA SETUP] Set up the VGA resolution. 2.[COLOR BAR TEST] Adjust the monitor colors by the color bar. VGA resolution setup: 1024*768/60HZ、800*600/60HZ、640*480/60HZ、 1024*768/75HZ、800*600/75HZ、640*480/75HZ Monitor colors’ adjustment by Color Bar.

  • Page 27

    JPEG2000 Stand alone DVR User Guide 4-3-1 HDD management 1.[HDD SETUP] BEGIN- Indicate the start Date/Time of recorded data on HDD (Master/Slave). RECORD- Indicate the end Date/Time of recorded data on HDD (Master/Slave). PLAY- Indicate the previous playback Date/Time on HDD (Master/Slave).

  • Page 28

    (2) Go to HDD management and CLEAR HDD (3) “RUN” all factory defaults. 2.DO NOT change the date and time after the recording starts It may corrupt the DVR’s data archive and cause playback errors. If it is necessary to change date and time after the recording starts, please run the above steps to avoid malfunctioning.

  • Page 29

    JPEG2000 Stand alone DVR User Guide [CAMERA COLOR SETUP] [CAMERA ACTIVE SETUP] [MOTION SETUP] Adjust the image color: Use [UP] and [DOWN] to select an item and use [-] and [+] or Jog shuttle to adjust the values. CHANNEL: Select the camera to be modified.

  • Page 30

    DVR keeps recording through out the event, and the duration after the last motion event. For example, the duration is set to 10 seconds and the motion last for 3 minutes. The DVR records for 3 minutes and 10 seconds.

  • Page 31

    1~99 SEC) 2.[EVENT RECORD] Event Update Time is to avoid the DVR from recording the event logs from the same event. The event types include alarm, motion and video loss. When an event is triggered, it is possible that the same event keeps on being triggered for a period of time.

  • Page 32

    Use [+] and [-] to set up a duration of the POPUP. The setting range is from 1 second to 60 seconds. When the Event POPUP finishes, 4CH DVR returns to its Quad screen display, 8CH DVR 9 -Split screen display, and 16CH DVR 16-Split screen display.

  • Page 33

    ※It can change Manager ‘s and Users’ password. 4-3-9 System information The product ID is not the DVR’s MAC address. MAC address can be found in [EXTERNAL DEVICE] > [TCP/IP setup]. The password consists of 1 to 8 digits. Press the number keys on the front panel to enter the password and you can use any combination of the numbers from 1 to 10 1.[USER ID]...

  • Page 34: Record Setup

    Under the Triplex mode, you may see the playback is slower than it is under the Duplex mode. The DVR uses the same component to process recording and the playback. As a result, the recording and the playback speed drop by 50% when the DVR enters playback under the Triplex mode.

  • Page 35

    1 /3 is to record at one third of the recording speed. You can set up the parameter from 1/1, 1/2, 1/3, 1/4,… to 1/999. 2. By lowering the recording speed, the DVR records less frames but gains a longer recording duration. If you set the DVR’s recording speed at 1/2, the recording duration will be two times longer.

  • Page 36: Schedule Record

    Time Zone Week 1. If the DVR is set to MOTION RECORDING and the DVR keeps recording continuously or is not triggered to record as you expect, please check the sensitivity settings and the motion mask setup in CONFIGURATION>CAMERA SETUP>MOTION SETUP.

  • Page 37

    3.[SIZE] Insert a blank CD disk and the DVR will check the disk size and displays on the screen. Press ENTER to enter the SIZE selection. Use [+] [-] or J.Shuttle to change the value. Press ENTER and the DVR caculates the end date and time for backup automatically.

  • Page 38: External Device

    JPEG2000 Stand alone DVR User Guide 4-6 External device 4-6-1 TCP/IP setup 1.[TCP/IP SETUP] Set up the DVR’s TCP/IP information. 2.[RS232C SETUP] Set up the parameters of the RS232 port. 3.[PANTILT SETUP] Set up the parameters of the PTZ control.

  • Page 39

    ENTER to confirm the settings and exit the selection. 3.[INTERVAL] Set up an interval for the DVR to report its IP address to the DDNS server automatically. (D- day / H- hour / M- minute). Press ENTER to enter the selection and [+] [-] or J.Shuttle to change the value.

  • Page 40

    2.[RETRY COUNT] Set up the times that the client tries to reconnect to the DVR. The client will quit trying to reconnect to the DVR after all the attempts fail. The setup range is from 0 to 20 attempts.

  • Page 41

    JPEG2000 Stand alone DVR User Guide 4-6-3 Pantilt setup [COMMAND SETUP] Please refer to CHAP.6 PTZ Camera Control for more details. Press to select and [+] / [-] to change the value. 1.[CHANNEL] Select PTZ channel. 2.[MODEL] Select PTZ protocol.

  • Page 42: Factory Default

    JPEG2000 Stand alone DVR User Guide [SPEED SETUP] 4-7 Factory default 1. The DVR cannot reset the password to default by running Factory Default. 2. It is strongly suggested to run Factory Default and HDD CLEAR when you install a new hard drive(s). 4-8 Language Press to select and [+] / [-] to change the value.

  • Page 43

    3.[SIZE] Insert a blank CD disk and the DVR will check the disk size. Press ENTER to choose a backup size. Use [+] [-] or J.Shuttle to change thevalue. Press ENTER and the DVR caculates the end date and time for backup automatically.

  • Page 44

    JPEG2000 Stand alone DVR User Guide CD Player software installation 3. Select a Destination Folder 1.Insert software CD. 2. Click [Install CD-R backup player] to start the installation. 4. Copy files to the Destination Folder. System will build a new icon of [CD BACKUP PLAYER] on PC [DESKTOP].

  • Page 45

    JPEG2000 Stand alone DVR User Guide CD Player software interface 1.Display screen: To display the backup image 2.Time display: To indicate the current time 3.Information window: To indicate the CD’s start/end time and date, and the backup video quality (resolution).

  • Page 46

    JPEG2000 Stand alone DVR User Guide Open AJP file 1. Select (OPEN) and the window below will show up on the screen. 2. Select the file and click [OPEN] to open the AJP file. Save JPG file 1. During playback and under FULL SCREEN MODE, when you see the picture you want to save, click EDIT.

  • Page 47: Chap.6 Ptz Camera Control

    Connect the PTZ’s D+ to the DVR’s D+, and D- to D-. 6-1-2 PTZ setup Each PTZ manufacturer may have different transmission buad rate. Please refer to the PTZ manuals for the detail information. Enter the baud rate suggested by the manufacturer in the DVR’s PTZ setup. [EXTERNAL DEVICE] SYSTEM MENU EXTERNAL DEVICE 1.

  • Page 48: Ptz Camera Operation

    JPEG2000 Stand alone DVR User Guide 6-2 PTZ camera operation [Operate by PTZ control keys] After entering PTZ control mode, PAN/TILT function can be controlled by direction keys and pre-assigned PTZ function keys. . Use MENU and NEXT key to select a PTZ command, and [+] [-] to select the channel.

  • Page 49: Network Installation And Setup

    CHAP.7 Network and client software 7-1 Network Introduction Users have to indentify what kind of Internet access they have before they set up the DVR’s network parameters. DSL and cable modem are the most popular broadband technologies. ADSL- Asymmetric Digital Subscriber Line ADSL is one of xDSL technologies, transmitting digital data over the wires of a local telephone network.

  • Page 50

    ENTER to switch DHCP to MANUAL In some very rare cases, we found the DVR did not support certain Static IP Addresses. If it happens, add a Router to the network system. The setup is the same as the next session, [Via ADSL with Dynammic IP.] [TP/IP SETUP] [IP CONFIG SETUP].

  • Page 51: Router Setup

    Go to [EXTERNAL DEVICE] [TCP/IP SETUP] [IP CONFIG SETUP] to enter the virtual IP address for the DVR and the IPs of gateway and subnet mask. Then, assign a port number to the DVR or you can use the default port number as well.

  • Page 52: Router Setup

    First, connect a computer to the router for configuration. In this example, the DVR’s IP is set to 192.168.1.53 and its port number is 8000. The router model is PCI BLW-04G. Enter the router’s setup and select Static IP or PPPoE.

  • Page 53

    JPEG2000 Stand alone DVR User Guide [PPPoE setup] 2. [Virtual server setup] Select PPPoE in WAN connection Type Enter User Name and Passward provided by your ISP The router will get the IP address upon connection. In this example, we get the IP address of 211.20.82.39.

  • Page 54: Client Software

    JPEG2000 Stand alone DVR User Guide Client software 7-4-1 Install and setup 7-4-2 Install Client software Insert the Install CD into CD-ROM, and the computer will auto-run the Install program. We suggest installing the software on Windows XP or Windows 2000.

  • Page 55

    To enter the setup 10.[Power ] To close the remote program. The connection to the DVR will break off after the remote software is closed. 11.[Transmission Rate] To adjust transimission speed, range from 1~10, the bigger it is, the faster it is, and the image quality is comparatively worse.

  • Page 56

    Press SAVE and then OK. Click CONNECT from Remote Viewer Interface 1. How to find out my real IP address: if you have computers connected to the router which the DVR is connected to, you can use your computer and go to http://www.whatismyip.com to find out your current IP address.

  • Page 57

    JPEG2000 Stand alone DVR User Guide [DDNS] 8. Click OK and then click CONNECT from Remote Viewer Interface. [DDNS LIST] 1.[Group] Enter Group name registered on DDNS Server. Please refer to 7-5 DDNS setup and operation for details. 2.[DVR Name] Enter DVR name registered on DDNS Server.

  • Page 58

    JPEG2000 Stand alone DVR User Guide [PTZ/SAVE] 7-4-5 PTZ control 1.[Circular Monitoring Interval] Set up a sequential switch interval. 2.[Scan Rate] Select a Fast forward (FF) speed of remote Playback. 3.[PTZ Type] Select the protocol used by your PTZ camera.

  • Page 59

    JPEG2000 Stand alone DVR User Guide 7-4-6 Remote playback [Remote Playback Interface] 5.[ Search Button ] To operate the search function 6.[Time Selection] To select the time of playback 7.[Channel Selection ] To select CAM1~16 when full screen display 8. [Auxiliary Function Button] SAVE : To save image as JPEG file to PC when the playback is paused.

  • Page 60

    Select a Year/Month/Day to playack. Click RW or PLAYBACK to start the playback If the DVR cannot find the selected playback date and time, the playback will starts from the next video clip. You can search a playback video clip by EVENT LIST. The events include Video Loss, Motion and Alarm.

  • Page 61

    JPEG2000 Stand alone DVR User Guide 7-4-7 Back up via Client software Save the recorded data as single JPEG picture or AVI format. [Save the recorded data as single JPEG picture] Press “STOP” right before where you want to save and press “SAVE”.

  • Page 62: Ddns Setup And Operation

    JPEG2000 Stand alone DVR User Guide 7-5 DDNS setup and operation DDNS SERVER setup 1. Connect to DDNS SERVER(http://advr.com.tw or http://59.124.143.151) by IE browser Select [REGISTER] to register a new account 2. Add a new account Group: Add a new user name...

  • Page 63

    [EXTERNAL DEVICE] [TCP/IP SETUP] [IP CONFIG SETUP] IP: Enter the DVR’s current IP address PORT: Enter the DVR’s port number ※It is required to enter DVR NAME and MAC ADDRESS. DVR’s IP and PORT number can be left blank.. Press [OK] to save the settings 6.

  • Page 64

    JPEG2000 Stand alone DVR User Guide DVR setup 1. The DVR setup is a onetime effort. First, make sure your DVR can be accessed over the Internet. Please refer to 7-2 Network installation and setup for details. 2. Go to [SYSTEM MENU] [ [EXTERNAL DEVICE] [TCP/IP SETUP] DDNS IP: 59.124.143.151...

  • Page 65

    JPEG2000 Stand alone DVR User Guide 2. Select DDNS in [IP/PORT] setup 3.Go to DDNS setup [DDNS INFO] GROUP: Enter Group nameregistered on DDNS Server. DVR NAME: Enter DVR name registered on DDNS Server. If the DVR name is entered and saved before, click LOAD to browse the list.

  • Page 66

    JPEG2000 Stand alone DVR User Guide Configuration of DDNS connection 1. DVR connect to DDNS server automatically and update the IP address by itself. 2. The client accessesto DDNS server and requests IP address from DDNS server. 3. DDNS server replies the DVR’s IP address and port number.

  • Page 67

    JPEG2000 Stand alone DVR User Guide Users can also access to the DVR from Internet Explore for remote viewing, remote backup, and playback the backup file. Log on to DDNS server and go to the DVR List Remote Live View via IE Browser Click WEB to link to your DVR 1.[Live picture]...

  • Page 68

    JPEG2000 Stand alone DVR User Guide Web Network Backup Click “Backup” to open the web page “Web Network Backup” 1.Backup Information: IP Address: Enter the IP address of DVR Network Port: Enter the port of DVR User ID: Enter “Admin”...

  • Page 69

    JPEG2000 Stand alone DVR User Guide 2. Function setup: Connect Test: To test the connection status Unlock: To get the record start/End time of DVR Set Backup Time: Set the start/end time, size and path of file backup Start Backup: Active the backup function 3.

  • Page 70

    JPEG2000 Stand alone DVR User Guide Play backup file Click [Backup Player] to open the web page of “Backup Player” 1. Display the backup image 2. Indicate the present time of monitoring 3. Indicate the start/end time of backup file 4.

  • Page 71

    JPEG2000 Stand alone DVR User Guide 8. Function keys: OPEN: Open the backup file EDIT: Edit the backup image AVI SAVE: To save the AVI file EXIT: Log out the program 9. audio options: ON: To start the audio function...

  • Page 72: Appendix.1 Record Time Table

    JPEG2000 Stand alone DVR User Guide Appendix.1 Record time table [4ch DVR] ※The numbers are for reference only. ※The recording duration is caculated under the continuous recording mode (Record speed :1/1X) - 72 -...

  • Page 73

    JPEG2000 Stand alone DVR User Guide [8/16ch DVR] ※The numbers are for reference only. ※The recording duration is caculated under the continuous recording mode (Record speed :1/1X) - 73 -...

  • Page 74: System Configuration

    JPEG2000 Stand alone DVR User Guide Appendix.2 System configuration - 74 -...

  • Page 75: Firmware Upgrade

    Install USB driver 1. Connect USB port between PC and DVR 2. Press and hold Search and Play keys on front panel and power on DVR 3. The DVR beeps for a moment. 4. When the Windows system detect new device, please select [Install from a list or specific location] 5.

  • Page 76

    JPEG2000 Stand alone DVR User Guide 7. Start to copy the driver to Windows system. 8. After installation, the USB device [BulkUsb.Sys Usb Bulk I/O Driver] can be found from [Device Manager]. - 76 -...

  • Page 77

    JPEG2000 Stand alone DVR User Guide Install USB upgrade program Insert the Install CD 1.Please select :[Install USB upgrade program(Allupdate) Set up Directory (default Directory ※ "C:\Program Files\J2000\Allupdate\") After installation, there’ll be a shortcut on desktop. Click on it for remote viewing.

  • Page 78: Upgrade Firmware

    3. Press and hold SEARCH and PLAY and power on the DVR. 4. When the DVR is powered on, you will hear very short beeps. Keep holding the “SEARCH” and “PLAY” buttons. When the beeps turn slow and the “Send” icon of the program, J2000 USB Downloader, becomes active, release the buttons 5.

  • Page 79

    2. Press and hold SEARCH and PLAY and power on the DVR 3. When the DVR is turned on, you will hear very short beeps. Keep holding the “SEARCH” and “PLAY” buttons. When the beeps turn slow and the “Send” icon of the program, J2000 USB Downloader, becomes active, release the buttons.

  • Page 80: Play Only Mode

    When you need to playback the video which you deleted by running HDD CLEAR Enter “PLAY ONLY MODE” Turn on the DVR. At the initial screen that says HDD DETECT, press [PLAY] and System enters “PLAY ONLY MODE”. To exit PLAY ONLY MODE, reboot the DVR and DO NOT press PLAY at the initial screen.

Comments to this Manuals

Symbols: 0
Latest comments: