Basic Operation; Starting The System; Loading Tracks And Playing Them (Ra); Using The Mixer Functions (Rb) - Pioneer DDJ-WeGO2 Operating Instructions Manual

Basic Operation

Starting the system

When using a computer
1 Connect this unit to your computer via a USB cable.
2 Boot up the connected computer.
3 Slide this unit's [ON/OFF] switch to the [ON] position.
Turn on the power of this unit.
! The message [Installing device driver software] may appear when
this unit is first connected to the computer or when it is connected to
a different USB port on the computer. Wait a while until the message
[Your devices are ready for use] appears.
Launching VIRTUAL DJ LE
About the order of operations when launching VIRTUAL
DJ LE
Always first turn on this unit's power, wait for the startup illumina-
tion to finish, check that this unit's [CTRL A], [FX1], [FX2], [FX3] and
[CTRL B] buttons are all lit dimly, then launch VIRTUAL DJ LE.
 Launching VIRTUAL DJ LE (Windows)
From the Windows [Start] menu, click the [All Programs]
> [VirtualDJ] > [VirtualDJ LE (DDJ-WeGO2)] icon.
 Launching VIRTUAL DJ LE (Mac OS X)
In Finder, open the [Application] folder, then double-
click the [VirtualDJ LE] icon.
When VIRTUAL DJ LE is launched the first time, a screen for entering the
serial number appears.
Input the serial number printed on this unit's bottom panel (XXXX-
XXXX-XXXXX/WEGO2), then click [OK].
When using an iPhone/iPad
Audio disorders (beeping) may occur in this unit when calling or send-
ing/receiving data on the mobile phone. This problem can arise when
the mobile phone's communications protocol is GSM, and is due to
interference caused by GSM. If this happens, change the iPhone/iPad's
setting to flight mode.
This problem does not occur with the 3G or LTE communications
protocols.
1 Connect the iPhone/iPad with this unit using the
iPhone/iPad connection cable (Lightning).
2 Connect this unit with the USB mobile battery or USB
power adapter.
3 Slide this unit's [ON/OFF] switch to the [ON] position.
4 Launch the DJ application on the iPhone/iPad.
12
En
D C C
Loading tracks and playing them
(rA)
1 Turn the rotary selector while pressing the [SHIFT]
button to select a folder or item.
! When a folder or item with the [+] mark is selected and the rotary
selector is pressed while pressing the [SHIFT] button, that folder or
item is opened or closed.
2 Release the [SHIFT] button then turn the rotary
selector to select the track.
3 Press the [LOAD] button to load the selected track
onto the deck.
4 Press the [f] button to play the track.
! When this button is pressed again during playback, playback
pauses.

Using the mixer functions (rB)

! Adjust the volume of the powered speakers, etc., connected to the
[MASTER OUT] terminals to an appropriate level. Note that if the
volume is set too high, the output sound could be very loud.
1 Operate the channel faders to adjust the audio level
output from the respective decks.
2 Operate the crossfader to switch the deck whose
sound is output from the speakers.
— Left edge: Sound is output from deck [A] or [C].
— Center: The sound of all the decks is mixed and output.
— Right edge: Sound is output from deck [B] or [D].
! The curve characteristics can be switched using the crossfader
curve setting button on the [MIXER] panel at the center of the com-
puter's screen.
— [ ]: Select this when you do not want to use the crossfader.
— [ ]: Set here for a curve that rises gradually.
— [ ]: Sets an abruptly rising curve.
3 Turn the [MASTER VOL] control to adjust the audio
level of the speakers.

Adjusting the sound quality

Turn the [EQ (HI, MID, LOW) ] controls on the respective
decks.
A B D
B