Table of Contents
Advertisement
Quick Links
RF Receiver
RFR-6
Instruction Manual
Thank you for purchasing the Integra RF
Receiver. Please read this manual
thoroughly before making connections
and plugging in the unit. Following the
instructions in this manual will enable you
to obtain optimum performance. Please
retain this manual for future reference.
Contents
Introduction.............. 3
About the RFR-6 ..................... 3
Applications ........................... 3
Installation ................ 4
the IR blaster ....................... 4
Mounting ................................ 5
the IR emitters ..................... 6
with IR IN terminal .............. 6
How to use the emitters ........ 7
Adapter .............................. 7
Settings .................................... 8
RF Interference ....................... 8
Troubleshooting ....... 9
Specifications .......... 10
E
n
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Integra RFR-6
Summary of Contents for Integra RFR-6
-
Page 1: Table Of Contents
How to use the emitters ..7 Connecting the Power Adapter ......7 Settings ........8 RF Interference ....... 8 Thank you for purchasing the Integra RF Troubleshooting ..9 Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you Specifications .. - Page 2 Precautions Care This device complies with Part 15 of the FCC From time to time you should wipe the unit rules. Operation is subject to the following two with a soft cloth. For heavier dirt, dampen a conditions: soft cloth in a weak solution of mild detergent (1) This device may not cause harmful interfer- and water, wring it out dry, and wipe off the ence, and (2) this device must accept any inter-...
-
Page 3: Introduction
C). ally any location. The RFR-6 is a RF Receiver ■ The set-ups in situation A, B and C can be that is used in combination with the RF Remote Controller. -
Page 4: Installation
Installation The following components should be present: IR blaster facing up RF Receiver, power adapter, Mono cable, 3 IR emitters, mounting plate and 4 screws. Maximum distance: 16 feet (5 m) Before you install the RF Receiver, you should decide which of the set-ups described on p. 3 ap- ply to your needs. -
Page 5: Mounting
Installation Mounting The RF Receiver can be mounted to a ceiling, a rack, etc. using the included mounting plate and the 4 screws. Take into account the range and the working angle of the IR blaster as explained on p. 4. Also make sure to place the RF Receiver in a central position aimed directly at your de- vices. -
Page 6: Using The Mono Cable And The Ir Emitters
IR blaster, the mono cable and 2 Plug the other end of the cable into the IR emitters. the RF Receiver. Note: IR terminals are different than connectors on Integra/Onkyo components. Do not connect IR terminals to connectors on Integra/Onkyo components. -
Page 7: How To Use The Emitters
Installation How to use the emitters Connecting the Power Adapter The IR emitters can be attached to the surround- ing surface facing the remote control sensor or directly to the remote control sensor. 1 Attach the emitters to a surface above, below or in front of the remote control sensor of your devices (for aesthetic appearance or when it is... -
Page 8: Settings
Installation Settings 3 Try to operate your devices with the RF Remote Controller. As the RF Receiver “communicates” with the The red LED will blink when the RF Re- RF Remote Controller, you have to set the same ceiver receives a correct command. Receiver ID (identity) on both appliances. -
Page 9: Troubleshooting
Troubleshooting Devices do not respond properly The red LED on the RF Receiver blinks ■ Check if the power adapter is connected and without using the RF Remote Controller the red LED is on. ■ This indicates RF interference. Another de- ■... -
Page 10: Specifications
Specifications The specifications and design of this product are subject to change without notice. Hardware Red LED (continuously on when powered, blinking during RF reception) 16 IDs and 4 CHs 4 outputs for mono cable and IR emitters Possibility to have multiple RF Receiver in one home not interfering Positioning: freestanding, mounted horizontally or hanging up side down 4.5 x 3.2 x 1.2 inch (113 x 81 x 30 mm) Dimensions... - Page 11 Memo...
- Page 12 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124...