Related Manuals for Integra DTR-30.6
Summary of Contents for Integra DTR-30.6
- Page 1 DTR-30.6 Basic Manual Advanced Manual found here http://integraworldwide.com/manual/dtr306/adv/en.html...
-
Page 2: Before Start
Before Start About the Basic Manual Features Supplied Accessories The Basic Manual leads you through the fundamental steps • Equipped with 7 channel amplifier to enjoy the AV Receiver from connections to TV, speaker • Incorporates Qdeo™ technology for HDMI video Indoor FM antenna --- (1) system and playback components, to necessary functions upscaling... -
Page 3: Connecting The Tv And Players
Step 1: Connections HDMI Personal computer HDMI To use the ARC function, connect to the ARC compatible HDMI jack of the TV and HDMI cable make an appropriate setting on the unit. See "2nd Step : Source Connection" of "Step 2: Setting Up". HDMI HDMI HDMI... -
Page 4: Connecting Components Without Hdmi
Step 1: Connections Analog connection: Use an analog audio (RCA) cable Home on the remote controller, select "Setup" - "1. Input/ Output Assign" - "Monitor Out" and set the default value of for connection with a player. "MAIN" to "SUB" or "MAIN+SUB". To enjoy multi-zone playback of audio of a CD player or such other player without HDMI output jack, you need The unit supports the HDMI Through function that allows... -
Page 5: Connecting Speakers
Step 1: Connections Connecting speakers Front R Front L Important: The power cord must be connected only after all Center other connections are completed. 1 2 Front speakers Center speaker 4 5 Surround speakers Subwoofer 7 8 Surround back speakers 9 F Height speakers • 5.1 ch: 1 2 3 4 5 6 • 7.1 ch: 1 2 3 4 5 6 + 7 8 or... -
Page 6: Other Connections
Step 1: Connections When using commercially available banana plugs: Network connection 1/2"-5/8"(12-15 mm) tighten the speaker terminals to the end and then insert the banana plugs. Do not insert the cable core directly into the You can enjoy Internet radio and DLNA by connecting hole for banana plug of speaker terminal. -
Page 7: Turning The Power On
Step 2: Setting Up Important: When the unit is turned on for the first time, the 1st Step : AccuEQ Room Calibration Making the Initial Setup with the Setup setup wizard of the section 2 will automatically be launched. If you use the setup wizard to make the initial setup, The test tone coming from each speaker will be measured Wizard... - Page 8 (e.g., "INT" for Integra) and search for the After checking the connection, select "Yes" with the Measurement will be made twice for each speaker. It remote control code.
-
Page 9: Establish Connection
Step 2: Setting Up 4th Step : Network Connection Select and set the authentication method. PIN code: Select this method when the automatic setting button of the access point is beyond the reach. Select "PIN code" with the cursor buttons and press Enter to display Wi-Fi Setup the 8-digit PIN code. -
Page 10: Playing Back
Step 3: Playing Back Remote controller parts name Playing the player and TV z Receiver button: Turns the unit on or into standby mode. RCV button: Switches the remote controller to the mode for operating this unit. Remote Mode/Input Selector button: Switches the input to be played. -
Page 11: Listening Modes
Step 3: Playing Back Listening modes Adjusting Sound Quality: It is possible to enhance or Listening to AM/FM Radio moderate the bass and treble of front speakers. Press Tone on the main unit several times to select the desired setting Select the desired mode by switching and listening actual sound in different modes. -
Page 12: Using The Home Menu
Step 3: Playing Back Playing sound of the Bluetooth-enabled device • "InstaPrevue" cannot be selected if the video is being Connecting and playing the Bluetooth- input from HDMI IN 5 or 6 or if there is no signal from the input currently selected. If the unit is on and the Bluetooth-enabled device is enabled device connected, the input will be automatically switched to... - Page 13 Step 3: Playing Back USB: Select "USB" in the TV screen and connect a USB Wide Mode: You can set the aspect ratio. • It cannot be set if the listening mode is Direct. storage device to the USB port on the front panel. On the Subwoofer Level, Center Level: Adjust the speaker Picture Mode: You can adjust the image quality.
-
Page 14: Making Multi-Zone Connection
Step 3: Playing Back Connecting speakers in another room • Output to multi-zone is not possible if the connection is Using the multi-zone function only with HDMI cable or digital cable. It is possible to directly connect the speakers in another • Analog audio output setting may be necessary on the room without an amplifier. -
Page 15: Performing Multi-Zone Playback
Step 3: Playing Back Performing Multi-zone Playback Press Zone2 on the remote controller, point the remote controller at the remote controller sensor and press zReceiver. "Z2" stays lit on the main unit display and the multi-zone function is enabled. Press Zone2 again on the remote controller and press Input Selector of the input to be played in a separate room. -
Page 16: Front Panel
(Australian model) Front Panel zOn/Standby button: Turns the unit on or into standby RT/PTY/TP button (Australian model): Can be used AUX Input HDMI/MHL jacks: An HD video camera or mode. when receiving the station transmitting text information. MHL-enabled mobile device is connected. It is possible to Bluetooth indicator: Flashes while pairing with a Memory button: Registers or deletes a station. -
Page 17: Rear Panel
Rear Panel RI REMOTE CONTROL jack: An Onkyo product with RI HDMI IN/OUT jacks: Digital video signals and audio DIGITAL IN COAXIAL/OPTICAL jacks: Digital audio jack can be connected and synchronized with this unit. signals are transmitted between the unit and the signals are input. - Page 18 Display Stays lit or flashes in the following conditions. Stays lit or flashes in the following conditions. "Z2": Zone 2 output is on. "AUTO": Tuning mode is auto. "HDMI": HDMI signals are input and the HDMI input "TUNED": Receiving AM/FM radio. selector is selected.
-
Page 19: Troubleshooting
Troubleshooting HDMI control does not function correctly. Resetting the unit Before starting the procedure • Set the CEC link function of the unit to on. It is also Problems may be solved by simply turning the power Resetting the unit to the status at the time of shipment may necessary to make the HDMI linked system setting on on/off or disconnecting/connecting the power cord, solve the problem. -
Page 20: Specifications
Specifications Amplifier Section Network Section HDMI Input Rated Output Power Ethernet LAN IN1 (BD/DVD, 4K), IN2 (CBL/SAT, 4K), IN3 (STB/DVR, 4K, HDCP2.2), All channels: 10BASE-T/100BASE-TX IN4 (GAME, 4K), IN5 (PC), IN6, AUX INPUT (HDMI/MHL) (Front) 95 watts minimum continuous power per channel, 8 ohm loads, Wireless LAN Output 2 channels driven from 20 Hz to 20 kHz, with a maximum total... -
Page 21: License And Trademark Information
License and Trademark Information The Bluetooth word mark and logos are registered trademarks owned by Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the ® double-D symbol are trademarks of Dolby Laboratories. Bluetooth SIG, Inc. and any use of such marks by Onkyo is under license. Other trademarks and trade names are those of their respective owners. - Page 22 DISCLAIMER For U.S. models Through this device you are able to link to other services or websites which CAUTION: This transmitter must not be co-located or operated in conjunction are not under the control of any company which has designed, manufactured with any other antenna or transmitter.
- Page 24 Integra Division of 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.integra.eu Integra Division of 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.integra.com.cn...