Page 1 Sebring Convertible 2 0 1 0 O W N E R ’ S M A N U A L...
Page 2: Introduction
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 4: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 5: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 6 INTRODUCTION 5...
Page 7: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 8: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 10: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 To Arm The System ....18 Ignition Key Removal .
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Open Window Feature — If Wind Buffeting ..... . . 35 Equipped .
Page 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 BeltAlert Programming ....50 Engine Break-In Recommendations ..77 Seat Belts And Pregnant Women .
Page 13: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer.
Page 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: • If you try to remove the key before you place the shift lever into PARK, the key may become trapped tempo- rarily in the ignition switch lock cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 15: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the Electronic Vehicle CAUTION! Information Center (EVIC), the power window switches, radio, hands–free system (if equipped), and An unlocked car is an invitation to thieves. Always power outlets will remain active for up to 10 minutes remove key from the ignition and lock all doors after the ignition switch is turned to the LOCK posi- when leaving the vehicle unattended.
Page 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The system uses ignition keys, which have an embedded If the Vehicle Security Light turns on during normal electronic chip (transponder), to prevent unauthorized vehicle operation (vehicle running for longer than 10 sec- vehicle operation.
Page 17: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys Customer Key Programming You can program new keys to the system if you have two NOTE: Only keys that have been programmed to the valid Sentry Keys by performing the following proce- vehicle electronics can be used to start the vehicle.
Page 18: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 4. Insert a blank Sentry Key into the ignition switch. dealer to have all remaining keys erased from the sys- Turn the ignition switch to the ON position within tems memory. This will prevent the lost key from starting 60 seconds.
Page 19: Vehicle Security Alarm - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED To Arm The System The Vehicle Security Alarm monitors the doors and trunk 1. Remove the keys from the ignition switch and get out for unauthorized entry and ignition switch for unautho- of the vehicle.
Page 20: To Disarm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: NOTE: • During the 16 second arming period, if a door is • The driver’s door key cylinder and the trunk button on opened or the ignition switch is turned ON, the the RKE transmitter cannot arm or disarm the Vehicle Vehicle Security Alarm will automatically disarm.
Page 21: Illuminated Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Alarm is armed and the battery This feature also turns on the approach lighting (if becomes disconnected the Vehicle Security Alarm will equipped). Refer to “Electronic Vehicle Information Cen- remain armed when the battery is reconnected.
Page 22: Remote Keyless Entry (Rke)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 REMOTE KEYLESS ENTRY (RKE) This system allows you to lock or unlock the doors, open the trunk, open the convertible top (if equipped), lower both door and rear quarter windows (if equipped), or activate the Panic Alarm from distances up to 66 ft (20 m) using a hand-held Remote Keyless Entry (RKE) transmit- ter.
Page 23 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Key Unlock, Driver Door/All Doors First 2. Release both buttons at the same time. Press 3. Test the feature while outside of the vehicle, by This feature lets you program the system to unlock either pressing the LOCK/UNLOCK buttons on the RKE trans- the driver’s door or both doors on the first press of the mitter with the ignition in the LOCK position, and the...
Page 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Flash Lights with Lock 3. Test the feature while outside of the vehicle, by The feature will cause the turn signal lights to flash when pressing the LOCK/UNLOCK buttons on the RKE trans- the doors are locked or unlocked with the RKE transmit- mitter with the ignition in the LOCK position, and the ter.
Page 25: To Lock The Doors
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the (EVIC)/Personal Settings (Customer-Programmable Fea- tures)” in “Understanding Your Instrument Panel” for following steps: further information. 1. Press the LOCK button on a programmed RKE trans- mitter for at least four seconds, but not longer than To Lock the Doors 10 seconds.
Page 26: Convertible Top Operation Button - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Convertible Top Operation Button — If Equipped Using the Panic Alarm Refer to “Convertible Top Operation” under “Under- To turn the Panic Alarm feature on or off, press and hold standing The Features Of Your Vehicle” for further the PANIC button on the RKE transmitter for at least one information.
Page 27: Programming Additional Transmitters
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters Refer to Sentry Key “Customer Key Programming.” If you do not have a programmed RKE transmitter, contact your authorized dealer for details. Battery Replacement The recommended replacement battery is CR2032. NOTE: •...
Page 28: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 General Information 2. Closeness to a radio transmitter such as a radio station This device complies with part 15 of FCC rules and with tower, airport transmitter, military base, and some mobile RS-210 of Industry Canada.
Page 29 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Hood closed WARNING! (Continued) • Trunk closed • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start • Hazard switch off System, windows, door locks or other controls •...
Page 30: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 the ignition switch must be cycled to the ON position DOOR LOCKS before you can repeat the start sequence for a third cycle. Manual Door Locks To Exit Remote Start Mode without Driving the To lock each door, push the door lock plunger on each Vehicle door trim panel downward.
Page 31: Power Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the door lock plunger is down when you shut the door, Power Door Locks the door will lock. Make sure the keys are not inside the A door lock switch is located on the driver and passenger vehicle before closing the door.
Page 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Auto Door Locks 6. The vehicle speed is 0 mph (0 km/h). When enabled, your door locks will lock automatically Auto Unlock Door on Exit Programming when the vehicle’s speed exceeds 15 mph (24 km/h). The The Automatic Unlock Doors on Exit feature can be Automatic Door Locks feature can be enabled or disabled enabled or disabled as follows:...
Page 33: Windows
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Press the power door UNLOCK switch to unlock the doors. 4. A single chime will indicate the completion of the programming. NOTE: This feature will not be functional until the vehicle has been driven and the shift lever returned to the PARK position.
Page 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: Smart Glass Feature • If a fluttering noise is heard from the rear seat belts The door window will lower slightly if the window is while driving with the windows down, safely bring fully up when opening the door.
Page 35 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For vehicles not equipped with the Electronic Vehicle To reactivate the window Smart Glass Feature, perform Information Center (EVIC), the power window switches the following steps after vehicle power is restored. will remain active for 45 seconds after the ignition switch 1.
Page 36: Wind Buffeting
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 button (setting it in the down position). To enable the Wind Buffeting window control, press and release the window LOCK Wind buffeting can be described as the perception of button again (setting it in the up position). pressure on the ears or a helicopter-type sound in the ears.
Page 37 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The trunk release button on the dash With the ignition ON, the word “deck” will display in the will be disabled if the vehicle is locked odometer indicating the trunk is open. The odometer by pressing the power door lock display will reappear once the trunk is closed or if the switch or by pressing the LOCK but-...
Page 38: Trunk Safety Warning
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 TRUNK SAFETY WARNING WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended.
Page 39 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Advanced Front Airbags for driver and front passen- all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat — if equipped •...
Page 40: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 of the worst injuries happen when people are thrown WARNING! from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the In a collision, you and your passengers can suffer inside of the vehicle.
Page 41 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Two people should never be belted into a single • Be sure everyone in your vehicle is in a seat and seat belt. People belted together can crash into one using a seat belt properly.
Page 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 2. The seat belt latch plate is on the outboard side of the 3. When the belt is long enough to fit, insert the latch front seat, next to your arm. Grasp the latch plate and plate into the buckle until you hear a “click.”...
Page 43 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • A shoulder belt placed behind you will not protect • A belt that is buckled into the wrong buckle will you from injury during a collision. You are more not protect you properly.
Page 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up • A lap belt worn too high can increase the risk of on the shoulder belt.
Page 45: Lap/Shoulder Belt Untwisting Procedure
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. 1. Position the latch plate as close as possible to the The belt will automatically retract to its stowed position. anchor point.
Page 46: Seat Belt Pretensioners - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 When To Use The Automatic Locking Mode Seat Belt Pretensioners — If Equipped Use the Automatic Locking Mode anytime a child safety The seat belts for both front seating positions may be seat is installed in a seating position that has a belt with equipped with pretensioning devices that are designed to this feature.
Page 47: Supplemental Active Head Restraints (Ahr)
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Active Head Restraints (AHR) When AHRs deploy during a rear impact, the front half These head restraints are passive, deployable compo- of the head restraint extends forward to minimize the gap nents, and vehicles with this equipment can not be between the back of the occupant’s head and the AHR.
Page 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 49 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand Positioning Points On AHR 2.
Page 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mecha- nism NOTE: • If you have difficulties or problems resetting the 4. The AHR front soft foam and trim half should lock Active Head Restraints, see an authorized dealer.
Page 51: Enhanced Seat Belt Use Reminder System (Beltalert )
60 seconds of starting the vehicle and if the vehicle speed NOTE: Chrysler Group LLC does not recommend de- is greater than 5 mph (8 km/h), the BeltAlert will alert activating BeltAlert .
Page 52: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 NOTE: Watch for the Seat Belt Reminder Light to turn Keep the belt low so that it does not come across the on while unbuckling and turn off while re-buckling the abdomen. That way the strong bones of the hips will take seat belt.
Page 53: Supplemental Restraint System (Srs) - Airbags
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) - Airbags This vehicle has Advanced Front Airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air- bag is mounted in the center of the steering wheel.
Page 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • After any collision, the vehicle should be taken to an The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of authorized dealer immediately. inflation that are based on the severity and type of Airbag System Components collision.
Page 55 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, WARNING! and Seat Track Position Sensors • No objects should be placed over or near the • Supplemental Active Head Restraint for Driver and airbag on the instrument panel, because any such Front Passenger objects could cause harm if the vehicle is in a...
Page 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! (Continued) • Do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. Supplemental Seat-Mounted Side Airbags (SAB) Supplemental Seat-Mounted Side Airbags provide en- hanced protection to help protect an occupant during a side impact.
Page 57 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Children 12 years old and under should always ride WARNING! buckled up in a rear seat. • Do not use accessory seat covers or place objects WARNING! between you and the side airbags; the performance could be adversely affected and/or objects could Infants in rear facing child restraints should NEVER be pushed into you, causing serious injury.
Page 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 If a child from 1 to 12 years old (not in a rear facing child 5. If the airbag system in this vehicle needs to be seat) must ride in the front passenger seat, move the seat modified to accommodate a disabled person, contact as far back as possible and use the proper child restraint.
Page 59: Airbag Deployment Sensors And Controls
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ORC deploys the Advanced Front Airbags, Supplemental WARNING! (Continued) Seat-Mounted Side Airbags — if equipped, and front seat • Being too close to the steering wheel or instrument belt pretensioners — if equipped, as required, depending panel during Advanced Front Airbag deployment on the severity and type of impact.
Page 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 The side airbags will not deploy in all side collisions. Side The ORC contains a backup power supply system that airbag deployment will depend on the severity and type may deploy the airbags even if the battery loses power or of collision.
Page 61 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE their full size. The airbags fully inflate in about 50 to 70 WARNING! milliseconds. This is about half of the time it takes to blink your eyes. The airbags then quickly deflate while Ignoring the Airbag Warning Light in your instru- helping to restrain the driver and front passenger.
Page 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Based on the severity and type of collision, the side power remains intact, depending on the nature of the airbag inflator on the crash side of the vehicle may be event the ORC will determine whether to have the triggered, releasing a quantity of non-toxic gas.
Page 63 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Front and/or side airbags will not deploy in all airbag inflation. These airborne particles may irritate collisions. This does not mean something is wrong with the skin, eyes, nose, or throat. If you have skin or eye the airbag system.
Page 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Maintaining Your Airbag System WARNING! (Continued) • Do not attempt to modify any part of your ad- WARNING! vanced airbag system. The airbag may inflate • Modifications to any part of the airbag system accidentally or may not function properly if modi- could cause it to fail when you need it.
Page 65: Event Data Recorder (Edr)
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light Controller (ORC) may also be disabled. The airbags may You will want to have the airbags ready to not be ready to inflate for your protection. Promptly inflate for your protection in a collision. While check the fuse block for blown fuses.
Page 66 Chrysler Group LLC, such investigations may be re- hicle, or crash, will be treated confidentially. Confidential quested by customers, insurance carriers, government data will not be disclosed by Chrysler Group LLC to any officials, and professional crash researchers, such as those third party except when: associated with universities, and with hospital and insur- ance organizations.
Page 67: Child Restraints
Child Restraints 2. Used in defense of litigation involving a Chrysler Everyone in your vehicle needs to be buckled up all the Group LLC product. time, including babies and children. Every state in the 3.
Page 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Infants and Child Restraints WARNING! • Safety experts recommend that children ride In a collision, an unrestrained child, even a tiny baby, rearward-facing in the vehicle until they are at least can become a projectile inside the vehicle. The force one year old and weigh at least 20 lbs (9 kg).
Page 69 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH child restraint anchorage system. Refer to restraint anchorage system. Refer to “LATCH — Child “LATCH — Child Seat Anchorage System (Lower Seat Anchorage System (Lower Anchors and Tether for Anchors and Tether for CHildren)”. CHildren)”.
Page 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 • The lap portion should be low on the hips and as snug WARNING! as possible. • Improper installation can lead to failure of an • Check belt fit periodically. A child’s squirming or infant or child restraint.
Page 71 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All passenger seating positions contain automatic Here are some tips on getting the most out of your child restraint: locking retractors. However, any seat belt system will loosen with time, so check the belt occasionally and •...
Page 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 for the installation of the child restraint without using the to the top tether anchorage, have been available for some vehicle’s seat belts. The two rear seating positions have time. In fact, many child restraint manufacturers will lower anchorages that are capable of accommodating provide add-on tether strap kits for some of their older LATCH-compatible child seats having flexible, webbing-...
Page 73 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because the lower anchorages are to be introduced to Remind all children in the vehicle that the seat belts are passenger carrying vehicles over a period of years, child not toys and should not be played with, and never leave restraint systems having attachments for those anchor- your child unattended in the vehicle.
Page 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 In addition, there are tether strap anchorages seat cover material. Then rotate the tether anchorage behind each rear seating position. Access ports cover directly behind the seat where you are placing the to the tether anchors are located in the panel child restraint, push the tether strap and hook through between the rear seat and the rear window.
Page 75 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraint installation, instead of tucking the seat belt Installing Child Restraints Using the Vehicle Seat behind the child restraint, route the seat belt through the Belts child restraint belt path and then buckle it. This should The passenger seat belts are equipped with Automatic stow the seat belt out of the reach of an inquisitive child.
Page 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 In the rear seat, you may have trouble tightening the 2. Open the access port cover (A) behind the seat where lap/shoulder belt on the child restraint because the you are placing the child restraint. buckle or latch plate is too close to the belt path opening on the restraint.
Page 77 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Open the access cover (C) on the carpet covering the WARNING! back of the seat and attach the tether strap hook (D) to the anchor. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
Page 78: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 ENGINE BREAK-IN RECOMMENDATIONS changes should be consistent with anticipated climate A long break-in period is not required for the engine and conditions under which vehicle operations will occur. For drivetrain (transmission and axle) in your vehicle. the recommended viscosity and quality grades refer to “Maintenance Procedures”...
Page 79: Safety Tips
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS WARNING! (Continued) Transporting Passengers • Be sure everyone in your vehicle is in a seat and NEVER TRANSPORT PASSENGERS IN THE CARGO using a seat belt properly. AREA. Exhaust Gas WARNING! WARNING! •...
Page 80: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 If it is necessary to sit in a parked vehicle with the engine Safety Checks You Should Make Inside the running, adjust your heating or cooling controls to force Vehicle outside air into the vehicle. Set the blower at high speed. Seat Belts The best protection against carbon monoxide entry into Inspect the belt system periodically, checking for cuts,...
Page 81 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster WARNING! Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Pedals that cannot move freely can cause loss of feel the air directed against the windshield. See your vehicle control and increase the risk of serious per- authorized dealer for service if your defroster is sonal injury.
Page 82: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Periodic Safety Checks You Should Make Outside WARNING! (Continued) the Vehicle • Check mounting of mats on a regular basis. Al- Tires ways properly reinstall and secure floor mats that Examine tires for excessive tread wear and uneven wear have been removed for cleaning.
Page 83 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.
Page 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....87 Emergency Bypass Mode (To Raise The Top Only) ......108 Power Convertible Top Usage Precautions .
Page 85 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command — If Equipped ... 112 Automatic Headlights — If Equipped ..124 Seats ......113 Headlights With Wipers (Available With Automatic Headlights Only) .
Page 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Windshield Wipers And Washers ..130 To Accelerate For Passing ....137 Intermittent Wiper System .
Page 87 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Features ..... . 149 Rear Window Features ....151 Storage .
Page 88: Convertible Top Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 CONVERTIBLE TOP OPERATION WARNING! CAUTION! The convertible top does not provide the structural protection that a reinforced metal roof does and the Failure to follow these cautions may cause interior fabric top cannot be expected to prevent the ejection water damage, stains or mildew on the top material: of the occupants in a collision.
Page 89: Power Convertible Top Usage Precautions
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When operating the power convertible top, the trunk lid Spring-loaded flipper doors, which provide clearance for will pivot at the rear of the vehicle, swing open by the the linkage, close off notches in the quarter trim panels rear window, and then pivot backward.
Page 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • The Power Top Control Module (PTCM) monitors and CAUTION! controls lowering and raising of the top. A series of • Correctly position the cargo shield in the trunk micro-switches verify that operations are complete before allowing the next stage of lowering or raising before stowing the top.
Page 91 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • To prevent striking a low ceiling or automatic door Before operating the power top: opener with the top, it is strongly recommended • Always check the tonneau cover area to be sure that you do not operate the power top inside a that it is clear of debris or other items.
Page 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 CAUTION! (Continued) CAUTION! (Continued) • Do not allow the top to remain in the suspended • Do not leave the top lowered for several weeks at position. After approximately 10 minutes in the a time.
Page 93: Cargo Shield
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Never place any extremities (hands, feet, etc.) near • When using the power top switch on the instru- the convertible top components, the upper wind- ment panel, if potential danger exists while raising shield area, the shelf area behind the rear seats, or the top, release the switch immediately to inter- the convertible top stowage area while raising or...
Page 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Positioning the Cargo Shield for Top Operation Pull the cargo shield toward you to begin unfolding the panels. Grasp the handle in the center of the outermost (top) panel and raise the cargo shield. Then, align and seat the tabs at each end of the cargo shield in the V slots in the trunk liner as shown in the illustration.
Page 95: Power Convertible Top Controls
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To stow the cargo shield, grasp the handle of the upright NOTE: The convertible top will NOT operate with the panel of the cargo shield, lifting the pins out of the V slots cargo shield in the stowed position.
Page 96: Lowering The Power Convertible Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 There is also a power top button on the Remote Keyless Lowering the Power Convertible Top Entry (RKE) transmitter for remotely lowering the power Using the Power Top Switch convertible top. NOTE: The power top switch will operate when the ignition switch is turned to the ON or ACC position and when in the power accessory delay.
Page 97: Raising The Power Convertible Top
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the Remote Keyless Entry Transmitter Press and hold the switch in the Top Up position until the operation of raising the top NOTE: Steps 1 – 3 must be performed within five and latching it is complete, which is indicated seconds.
Page 98: Wind Stop - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Manually Wind Stop — If Equipped Closing the power convertible top manually is a compli- The Wind Stop installs in the backseat area of the vehicle. cated and physically demanding procedure, and it re- The Wind Stop will not interfere with power top opera- quires a special tool to do so.
Page 99 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The frames must lie flat on each other in order to 4. Pivot the small frame (1) away from the large frame (2) snap them together. until the pivot lock (3) engages to lock the two frames in an L shape.
Page 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 5. Unfold both stems at the rear of the large frame. 6. Align and insert the stems into the slot in each trim panel.
Page 101 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Align the pins at the front of the large frame with the Disengage the pivot lock (1) to fold the small frame flat hole in each trim panel. Slide the pins outward until fully onto the large frame.
Page 102: Power Convertible Top Operation And Warning Messages
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Power Convertible Top Operation and Warning (EVIC) – if equipped, or in the Odometer for vehicles not Messages equipped with the EVIC. Refer to the following chart for When the appropriate conditions exist, the PTCM dis- message related information: plays various power convertible top operation and warn- ing messages in the Electronic Vehicle Information Center...
Page 103 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/ Time [8 km/ Time CONVERT- 9 sec.
Page 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/ Time [8 km/ Time CONVERT- Until Op- TOP nOT...
Page 105 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/ Time [8 km/ Time SPEED 9 sec.
Page 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/ Time [8 km/ Time TRUNK Continu- DECK...
Page 107 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/ Time [8 km/ Time CONVERT- Until Fault TOP FAIL...
Page 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • If you are trying to lower the top and ambient temperature is 0°F (-18°C) or lower, wait until the temperature rises and the top is thawed and dry before operating the power top. A soft top should not be lowered at tem- peratures below 32°F (0°C).
Page 109: Emergency Bypass Mode (To Raise The Top Only)
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Bypass Mode (To Raise the Top Only) CAUTION! (Continued) This procedure is only to be used to raise the top when • Using the Emergency Bypass Mode could poten- the top cannot be returned to the UP (raised) position by tially damage the convertible top and should only pressing the POWER TOP switch or is in a position in be used to raise the power top to the UP (raised)
Page 110: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated.
Page 111: Outside Mirrors
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Power Mirrors To receive maximum benefit, adjust the outside mirrors The power mirror switch is located on the driver’s door to center on the adjacent lane of traffic and a slight trim.
Page 112: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 After selecting a mirror, move the knob in the same Heated Mirrors — If Equipped direction you want the mirror to move. When finished, These mirrors are heated to melt frost or ice. This return the knob to the center “O”...
Page 113: Vanity Mirror - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirror — If Equipped Uconnect™ Phone — IF EQUIPPED A vanity mirror is attached to the inside face of the sun Refer to “Uconnect™ Phone” in the Uconnect™ User visor. To use the mirror, rotate the sun visor downward Manual located on the DVD for further details.
Page 114: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 115: Heated Seats - If Equipped
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped WARNING! The driver and front passenger seats are heated. The • Adjusting a seat while the vehicle is moving is controls for each heater are located in the instrument panel switch bank above the climate controls.
Page 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 WARNING! CAUTION! • Persons who are unable to feel pain to the skin Repeated overheating of the seat could damage the because of advanced age, chronic illness, diabetes, heating element and/or degrade the material of the spinal cord injury, medication, alcohol use, ex- seat.
Page 117: Recliner Adjustment
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recliner Adjustment WARNING! The recliner control is on the outboard side of the seat. To • Adjusting a seat while the vehicle is moving is recline the seat, lean forward slightly and lift the lever. Then lean back to the position desired and release the dangerous.
Page 118: Easy Entry System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Lumbar Support Easy Entry Lever Easy Entry System Pull the lever upward to move the seat and seatback The Easy Entry lever is located on upper seat belt anchor forward. cover. When returning the seat to its normal position, the memory feature restores the seat position and seatback recline position to their current settings.
Page 119: Adjusting Active Head Restraints
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On the driver seat, pull the lever upward to move the seatback forward. When returning the seatback to its normal position the memory feature restores the seatback recline position to its current setting. Adjusting Active Head Restraints Active Head Restraints can reduce the risk of injury in the event of a rear impact.
Page 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 To raise the head restraint, pull upward on the head For comfort the Active Head Restraints can be tilted restraint (on some models, you may need to press the forward and backward. To tilt the head restraint closer to push button).
Page 121 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.
Page 122: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 TO OPEN AND CLOSE THE HOOD WARNING! (Continued) Two latches must be released to open the hood. • Do not place items over the top of the Active Head 1. Pull the hood release lever located under the left side Restraint, such as coats, seat covers or portable of the instrument panel.
Page 123 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the outside of the vehicle and lift the second- ary latch underneath the center front edge of the hood and raise the hood. Hood Prop Rod Hole Location Before closing the hood, make sure to stow the prop rod in its proper location.
Page 124: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 LIGHTS CAUTION! Multifunction Lever To prevent possible damage, do not slam the hood to The multifunction lever on the left side of the steering close it. Use a firm downward push at the center of column controls the operation of the headlights, parking the hood to ensure that both latches engage.
Page 125: Headlights And Parking Lights
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights And Parking Lights Lights-On Reminder Turn the end of the multifunction lever to the first detent If the headlights or parking lights are on after the ignition for parking light operation. Turn the end of the lever to is turned to the LOCK position, a chime will sound to the second detent for headlight operation.
Page 126: Headlights With Wipers (Available With Automatic Headlights Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Headlights with Wipers (Available with Automatic To activate the delay, turn the ignition switch to the Headlights Only) LOCK position while the headlights are still on. Then, When this feature is active, the headlights will turn on turn off the headlights within 45 seconds.
Page 127: Instrument Panel Dimmer
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on.
Page 128: Fog Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Fog Lights — If Equipped NOTE: The front fog lights will only operate with the To activate the front fog lights, turn on the parking headlights on low beam. Selecting high beam headlights lights or the low beam headlights and pull out on will turn off the front fog lights.
Page 129: Turn Signals
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Lane Change Assist Move the multifunction lever up or down and the arrows Tap the lever up or down once, without moving beyond on each side of the instrument cluster flash to show the detent, and the turn signal (right or left) will flash proper operation of the front and rear turn signal lights.
Page 130: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Interior Lights A courtesy light is also found in the rear of the center Two courtesy/reading lights are located in the bottom of console. You can turn this light on and off from the the rearview mirror.
Page 131: Windshield Wipers And Washers
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. Changing Wiper Speeds NOTE: The wipers will automatically return to the “Park” position if you turn the ignition switch OFF while they are operating.
Page 132: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 regulate the wipe interval from a minimum of one cycle CAUTION! every second to a maximum of approximately 18 seconds • Turn the windshield wipers off when driving between cycles. through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off.
Page 133: Mist Feature
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
Page 134: Headlights With Wipers (Available With Auto Headlights Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Headlights with Wipers (Available with Auto Windshield Washers Headlights Only) To use the washer, pull the windshield wiper/washer When this feature is active, the headlights will turn on control lever toward you and hold it for as long as approximately 10 seconds after the wipers are turned on washer spray is desired.
Page 135: Tilt/Telescoping Steering Column
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN To unlock the steering column, push the control handle This feature allows you to tilt the steering column downward. To tilt the steering column, move the steering upward or downward. It also allows you to lengthen or wheel upward or downward as desired.
Page 136: Electronic Speed Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 ELECTRONIC SPEED CONTROL NOTE: In order to ensure proper operation, the Elec- When engaged, the Electronic Speed Control takes over tronic Speed Control System has been designed to shut the accelerator operation at speeds greater than 25 mph down if multiple Speed Control functions are operated at (40 km/h).
Page 137: To Set A Desired Speed
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate WARNING! A soft tap on the brake pedal, or pulling the Electronic Speed Control lever toward you (CANCEL), or normal Leaving the Electronic Speed Control on when not in brake pressure while slowing the vehicle will deactivate use is dangerous.
Page 138: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 ACCEL lever. If the lever is continually held in the WARNING! RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed Electronic Speed Control can be dangerous where the will be established.
Page 139: Garage Door Opener - If Equipped
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On steep hills, a greater speed loss or gain may occur so The HomeLink buttons that are located in the headliner it may be preferable to drive without Electronic Speed or sun visor designate the three different HomeLink Control.
Page 140: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Programming HomeLink WARNING! Before You Begin • Your motorized door or gate will open and close If you have not trained any of the HomeLink buttons, while you are training the universal transceiver. erase all channels before you begin training.
Page 141 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After training a HomeLink channel, if the garage Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink button you wish to program while door does not operate with HomeLink and the ga- keeping the indicator light in view.
Page 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer.
Page 143: Gate Operator/Canadian Programming
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink Gate Operator/Canadian Programming To operate, press and release the programmed Canadian radio frequency laws require transmitter sig- HomeLink button. Activation will now occur for the nals to time-out (or quit) after several seconds of trans- trained device (i.e., garage door opener, gate operator, mission –...
Page 144: Security
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 successfully accepted the frequency signal. The indica- Troubleshooting Tips tor light will flash slowly and then rapidly when fully If you are having trouble programming HomeLink , here trained. are some of the most common solutions: •...
Page 145: Electrical Power Outlets
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be NOTE: Do not exceed the maximum power of 160 Watts received including interference that may cause undesired (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power operation.
Page 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Instrument Panel Power Outlet Center Console The center console power outlet is powered directly from WARNING! the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or To avoid serious injury or death: •...
Page 147 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) CAUTION! (Continued) • Do not touch with wet hands. • Accessories that draw higher power (i.e., coolers, • Close the lid when not in use and while driving vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
Page 148: Cigar Lighter And Ash Receiver - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 CIGAR LIGHTER AND ASH RECEIVER — IF CAUTION! EQUIPPED An optional ash receiver is available from your autho- For vehicles equipped with the heated and cooled rized dealer and will fit in the center console front cupholder, locate the cup holder ash receiver in the cupholder.
Page 149: Cupholders
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Rear Seat Cupholders Cupholders for the rear seat occupants are located in the Front Seat Cupholder armrests. Each cupholder is capable of holding up to a The cupholder in the center console will accommodate 20 oz.
Page 150: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! If containers of hot liquid are place in the cupholder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury. CONSOLE FEATURES Storage The center console contains a cubby bin with flip-down cover located below the climate controls.
Page 151 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also con- tains a 12 Volt power outlet and a molded-in coin holder (designed to hold various size coins).
Page 152: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Sliding Armrest — If Equipped REAR WINDOW FEATURES On some models the center console armrest slides for- Rear Window Defroster ward and rearward for added user comfort. The rear window defroster button is located on the climate control (Mode) knob.
Page 153 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
Page 154: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....156 Personal Settings (Customer-Programmable Features) ......179 Instrument Cluster .
Page 155 154 UNDERSTANDING YOUR INSTRUMENT PANEL List Button (Disc Mode For Operating Instructions — Radio Mode ..202 MP3/WMA Play) ....195 Operation Instructions —...
Page 156 UNDERSTANDING YOUR INSTRUMENT PANEL 155 Operating Instructions - Uconnect™ Phone Remote Sound System Controls — (If Equipped) ..... . . 223 If Equipped .
Page 157: Instrument Panel Features
156 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 6 — Radio 11 — Hazard Switch 2 — Side Window Demister Outlet 7 — Passenger Airbag 12 — Storage Compartment 3 — Instrument Cluster 8 — Glove Compartment 13 —...
Page 158: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 157 INSTRUMENT CLUSTER...
Page 159: Instrument Cluster Descriptions
158 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and 1. Temperature Gauge the Fan control to High. This allows the heater core to act The temperature gauge shows engine coolant tempera- as a supplement to the radiator and aids in removing heat ture.
Page 160 UNDERSTANDING YOUR INSTRUMENT PANEL 159 5. Low Fuel Light If jump starting is required, refer to “Jump Starting When the fuel level drops to approximately 2.0 gal- Procedures” in “What To Do In Emergencies”. lons (7.6 Liters), the fuel symbol will light and a 7.
Page 161 160 UNDERSTANDING YOUR INSTRUMENT PANEL you do not buckle up, the light will remain on. Refer to 10. Engine Temperature Warning Light “Occupant Restraints” in “Things To Know Before Start- This light warns of an overheated engine condi- ing Your Vehicle” for further information. tion.
Page 162 UNDERSTANDING YOUR INSTRUMENT PANEL 161 The light will remain on until the cause is corrected. In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair NOTE: The light may flash momentarily during sharp to the ABS system is required.
Page 163 162 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Tachometer the same as it was before the repair or service. If s/he The silver area of the scale shows the permissible engine cannot do so, then the odometer must be set at zero, and revolutions-per-minute (RPM x 1000) for each gear range.
Page 164 UNDERSTANDING YOUR INSTRUMENT PANEL 163 Vehicle Odometer Messages LoW TirE When the appropriate conditions exist, the odometer will When the appropriate condition exists, the odometer display the following messages: display will toggle between LoW and TirE for three cycles. door ......Door Ajar HOTOIL deck .
Page 165 164 UNDERSTANDING YOUR INSTRUMENT PANEL tighten the fuel filler cap properly and press the odom- To turn off the message temporarily, press and release the eter reset button to turn off the “gASCAP” message. Trip Odometer button on the instrument cluster. To reset (Refer to “Onboard Diagnostic System —...
Page 166 UNDERSTANDING YOUR INSTRUMENT PANEL 165 15. Cruise Indicator — If Equipped Dual Trip Odometer — If Equipped This indicator shows that the Electronic Speed Press and release this button to change the display from Control System is ON. odometer to “Trip A.” Press and release it a second time to change the display to “Trip B.”...
Page 167 166 UNDERSTANDING YOUR INSTRUMENT PANEL If the light is flashing when the engine is running you 20. Turn Signal Indicators may experience power loss, an elevated/rough idle, and The arrows will flash in unison with the exterior increased brake pedal effort, and your vehicle may turn signal, when using the turn signal lever.
Page 168 UNDERSTANDING YOUR INSTRUMENT PANEL 167 If the ABS light remains on or comes on during driving, 24. Electronic Stability Control (ESC) Malfunction it indicates that the Anti-Lock portion of the brake system Indicator Light — If Equipped is not functioning and that service is required, however, The “ESC Malfunction Indicator Light”...
Page 169 168 UNDERSTANDING YOUR INSTRUMENT PANEL • Each time the ignition is turned ON, the ESC system (TPMS) that illuminates a low tire pressure telltale when will be ON even if it was turned off previously. one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- •...
Page 170 UNDERSTANDING YOUR INSTRUMENT PANEL 169 system detects a malfunction, the telltale will flash for CAUTION! approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- The TPMS has been optimized for the original quent vehicle start-ups as long as the malfunction exists. equipment tires and wheels.
Page 171 170 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Malfunction Indicator Light (MIL) CAUTION! The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD that Prolonged driving with the MIL on could cause monitors emissions, engine, and automatic trans- damage to the engine control system.
Page 172 UNDERSTANDING YOUR INSTRUMENT PANEL 171 27. Transmission Temperature Warning Light — If WARNING! Equipped This light indicates that the transmission fluid Continued operation with the Transmission Tem- temperature is running hot. This may occur perature Warning Light illuminated could cause the with severe usage, such as trailer towing.
Page 173: Electronic Vehicle Information Center (Evic) - If Equipped
172 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER The EVIC consists of the following: (EVIC) – IF EQUIPPED • System Status The Electronic Vehicle Information Center (EVIC) fea- • Vehicle information warning message displays tures a driver-interactive display that is located in the instrument cluster.
Page 174: Electronic Vehicle Information Center (Evic) Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 173 The system allows the driver to select information by Press and release the RESET Button to accept a pressing the following buttons on the instrument panel selection. The RESET Button also resets various switch bank located below the climate controls: Trip Functions.
Page 175: Oil Change Required - If Equipped
174 UNDERSTANDING YOUR INSTRUMENT PANEL • RKE (Remote Keyless Entry) Battery Low (with a • Speed Too High (with a single chime) single chime) • Convertible Top Malfunction (with a single chime) • Personal Settings Not Available – Vehicle Not in Park •...
Page 176: Trip Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 175 • Elapsed Time release the Menu button. To reset the oil change indicator system (after performing the scheduled maintenance) • Display Units of Measure in perform the following procedure: Press and release the STEP button to advance the display 1.
Page 177: Compass Display
176 UNDERSTANDING YOUR INSTRUMENT PANEL • Display Units In: and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the RESET To make your selection, press and release the RESET button. button until “ENGLISH” or “METRIC” appears. NOTE: Significant changes in driving style or vehicle To Reset The Display loading will greatly affect the actual drivable distance of...
Page 178 UNDERSTANDING YOUR INSTRUMENT PANEL 177 NOTE: The system will display the last known outside Manual Compass Calibration temperature when starting the vehicle and may need to If the compass appears erratic, inaccurate, or abnormal, be driven several minutes before the updated tempera- you may wish to calibrate the compass manually.
Page 179 178 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Drive the vehicle slowly, completing one or more circles (in an area free from large metal or metallic objects) until the CAL indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between magnetic North and Geographic North.
Page 180: Personal Settings (Customer-Programmable Features)
UNDERSTANDING YOUR INSTRUMENT PANEL 179 3. Press and release the STEP button until “Compass Press and release the MENU button until “Personal Variance” and the current Variance Value displays in the Settings” displays in the EVIC. EVIC. Press and release the STEP button to display the follow- 4.
Page 181 180 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Key Unlock Flash Lights with LOCK When Driver Door 1st Press is selected, only the driver’s When ON is selected, the front and rear turn signals will door will unlock on the first press of the Remote Keyless flash when the doors are locked or unlocked with the Entry (RKE) transmitter UNLOCK button.
Page 182 UNDERSTANDING YOUR INSTRUMENT PANEL 181 off if they were turned on by this feature. To make your Illuminated Approach selection, press and hold the RESET button until ON or When this feature is selected, the headlights will activate OFF appears. and remain on for up to 90 seconds when the doors are unlocked with the remote keyless entry transmitter.
Page 183: Setting The Analog Clock
182 UNDERSTANDING YOUR INSTRUMENT PANEL SETTING THE ANALOG CLOCK MEDIA CENTER 230 (REQ) — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. To set the analog clock, located at the top center of the instrument panel, press and hold the button in until the setting is correct.
Page 184: Operating Instructions - Radio Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 183 Operating Instructions - Radio Mode to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection.
Page 185 184 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button Uconnect™ Phone — If Equipped 3. After adjusting the hours, press the right side TUNE/ Press this button to operate the Uconnect™ Phone feature SCROLL control knob to set the minutes. The minutes (if equipped).
Page 186 UNDERSTANDING YOUR INSTRUMENT PANEL 185 RW/FF Push the rotary TUNE/SCROLL control knob a third Pressing the RW (Rewind) or FF (Fast Forward) buttons time and TREBLE will display. Turn the TUNE/SCROLL causes the tuner to search for the next frequency in the control knob to the right or left to increase or decrease the direction of the arrows.
Page 187 186 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Program Type 16-Digit Character Display Pressing this button once will turn on the Music Type Jazz Jazz mode for five seconds. Pressing the MUSIC TYPE button News News or turning the TUNE/SCROLL control knob within five Nostalgia Nostalga seconds will allow the program format type to be se-...
Page 188 UNDERSTANDING YOUR INSTRUMENT PANEL 187 • DVD Enter - When the disc is in DVD Menu mode, By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency selecting DVD Enter will allow you to play the current station with the same selected Music Type name.
Page 189 188 UNDERSTANDING YOUR INSTRUMENT PANEL • Angle – Repeatedly pressing SELECT will change • Set Home Clock - Pressing the SELECT button allows the viewing angle if supported by the DVD disc (if you to set the clock. Turn the TUNE/SCROLL control equipped).
Page 190 UNDERSTANDING YOUR INSTRUMENT PANEL 189 Audio Language — If Equipped Audio DRC — If Equipped Selecting this item allows you to choose a default audio Selecting this item allows you to limit maximum audio language (effective only if the language is supported by dynamic range.
Page 191 190 UNDERSTANDING YOUR INSTRUMENT PANEL a disc is loaded, changes will not be effective. Also, the both AM and FM. This allows a total of 12 AM, 12 FM, defaults are effective only if the disc supports the and 12 Satellite (if equipped) stations to be stored into customer-preferred settings.
Page 192: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Operation Instructions - (DISC MODE for CD and NOTE: The ignition switch must be in the ON or ACC MP3/WMA Audio Play, DVD-VIDEO) position to operate the radio. The radio DVD player and many DVD discs are coded by LOAD Button —...
Page 193 192 UNDERSTANDING YOUR INSTRUMENT PANEL Eject Button — Ejecting Compact Disc(s) SCAN Button (CD MODE) Press the EJECT button and the pushbutton Press the SCAN button to scan through each track on the with the corresponding number (1-6) where the CD currently playing.
Page 194: Notes On Playing Mp3/Wma Files
UNDERSTANDING YOUR INSTRUMENT PANEL 193 Notes On Playing MP3/WMA Files The radio uses the following limits for file systems: The radio can play MP3/WMA files; however, acceptable • Maximum number of directory levels: 8 MP3/WMA file recording media and formats are limited. •...
Page 195 194 UNDERSTANDING YOUR INSTRUMENT PANEL If a disc contains multi-formats, such as CD audio and MPEG Sampling Bit Rate (kbps) MP3/WMA tracks, the radio will only play the MP3/ Specification Frequency (kHz) WMA tracks on that disc. 320, 256, 224, MPEG-1 Audio 192, 160, 128, Supported MP3/WMA File Formats...
Page 196: List Button (Disc Mode For Mp3/Wma Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Playback of MP3/WMA Files LIST Button (DISC Mode for MP3/WMA Play) When a medium containing MP3/WMA data is loaded, Pressing the LIST button will bring up a list of all folders the radio checks all files on the medium. If the medium on the disc.
Page 197 196 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds SCAN Button (Auxiliary Mode) to return to elapsed time display. No function. Operation Instructions - Auxiliary Mode EJECT Button (Auxiliary Mode) The auxiliary (AUX) jack is an audio input jack which No function.
Page 198 UNDERSTANDING YOUR INSTRUMENT PANEL 197 Operating Instructions — Voice Command System Operating Instructions - Video Entertainment (If Equipped) System (VES)™ (If Equipped) For the radio, Refer to “Voice Command” in the Refer to “Video Entertainment System (VES)™” in the Uconnect™ User Manual located on the DVD for further Uconnect™...
Page 199: Media Center 730N/430 (Rer/Ren/Rbz) - Am/Fm Stereo Radio And Cd/Dvd/Hdd/ Nav - If Equipped
198 UNDERSTANDING YOUR INSTRUMENT PANEL DTS™ Operating Instructions — Voice Command DTS™ and DTS™ 2.0 are trademarks of Digital The- System — If Equipped ater Systems, Inc. Refer to “Voice Command” in the Uconnect™ User Manual located on the DVD for further details. MEDIA CENTER 730N/430 (RER/REN/RBZ) —...
Page 200 UNDERSTANDING YOUR INSTRUMENT PANEL 199 3. To move the hour forward, touch the screen where the 2. Touch the screen where the time is displayed. The word “Hour” with the arrow pointing upward is dis- clock setting menu will appear on the screen. played.
Page 201: Clock Setting Procedure - Rer/Ren Radio
200 UNDERSTANDING YOUR INSTRUMENT PANEL Changing the Time Zone satellite clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the system’s 1. Turn on the radio. clock very accurate once the appropriate time zone and 2.
Page 202 UNDERSTANDING YOUR INSTRUMENT PANEL 201 displayed. To move the minute backward, touch the Show Time if Radio is Off screen where the word “Min” with the arrow pointing When selected, this feature will display the time of day downward is displayed. on the touch screen when the radio is turned off.
Page 203: Media Center 130 (Res) - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
202 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 4. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen.
Page 204 UNDERSTANDING YOUR INSTRUMENT PANEL 203 Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio. Push the ON/VOLUME control knob a second and radio frequency. time to turn off the radio.
Page 205 204 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Push the rotary TUNE/SCROLL control knob a third Pressing the RW (Rewind) or FF (Fast Forward) buttons time and TREBLE will display. Turn the TUNE/SCROLL causes the tuner to search for the next frequency in the control knob to the right or left to increase or decrease the direction of the arrows.
Page 206: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 205 SET/RND Button — To Set the Pushbutton Every time a preset button is used, a corresponding Memory button number will display. When you are receiving a station that you wish to Buttons 1 - 6 commit to pushbutton memory, press the SET/RND These buttons tune the radio to the stations that you button.
Page 207 206 UNDERSTANDING YOUR INSTRUMENT PANEL discs (CD-RW), compact discs with MP3 tracks and CAUTION! multisession compact discs with CD and MP3 tracks. • This CD player will accept 4-3/4 in (12 cm) discs Inserting Compact Disc(s) only. The use of other sized discs may damage the Gently insert one CD into the CD player with the CD CD player mechanism.
Page 208 UNDERSTANDING YOUR INSTRUMENT PANEL 207 If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold the FF (Fast Forward) button and the CD the radio will reinsert the CD but will not play it.
Page 209: Notes On Playing Mp3 Files
208 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 Notes on Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited.
Page 210 UNDERSTANDING YOUR INSTRUMENT PANEL 209 Discs created with an option such as keep disc open after MPEG Sampling Bit Rate (kbps) writing are most likely multisession discs. The use of Specification Frequency (kHz) multisession for CD audio or MP3 playback may result in 320, 256, 224, longer disc loading times.
Page 211: Operation Instructions - Auxiliary Mode
210 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files Operation Instructions - Auxiliary Mode When a medium containing MP3 data is loaded, the The auxiliary (AUX) jack is an audio input jack, which radio checks all files on the medium. If the medium allows the user to plug in a portable device, such as an contains a lot of folders or files, the radio will take more MP3 player, or cassette player, and utilize the vehicle’s...
Page 212: Media Center 130 (Res/Rsc) - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack) And Sirius Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 211 MEDIA CENTER 130 (RES/RSC) — AM/FM Operating Instructions — Radio Mode STEREO RADIO WITH CD PLAYER (MP3 AUX NOTE: The ignition switch must be in the ON/RUN or JACK) AND SIRIUS RADIO ACC position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 213 212 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons If your vehicle is not equipped with or this feature is not Press and release the SEEK buttons to search for the next available on your vehicle, a “Not Equipped With listenable station in AM/FM mode. Press the right switch Uconnect”...
Page 214 UNDERSTANDING YOUR INSTRUMENT PANEL 213 Clock Setting Procedure starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above 1. Press and hold the TIME button until the hours blink. procedure, starting at Step 2. 2.
Page 215 214 UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob a fifth time Push the rotary TUNE/SCROLL control knob and BASS and FADE will display. Turn the TUNE/SCROLL control will display. Turn the TUNE/SCROLL control knob to knob to the left or right to adjust the sound level between the right or left to increase or decrease the bass tones.
Page 216 UNDERSTANDING YOUR INSTRUMENT PANEL 215 Toggle the MUSIC TYPE button to select the following 16-Digit Character Program Type format types: Display 16-Digit Character Personality Persnlty Program Type Display Public Public No program type Rhythm and Blues R & B None or undefined Religious Music Rel Musc...
Page 217 216 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon the minutes using the right side TUNE/SCROLL is displayed, the radio will be tuned to the next frequency control knob. Press the TUNE/SCROLL control knob station with the same selected Music Type name.
Page 218: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 217 You may add a second station to each pushbutton by Operation Instructions — CD MODE for CD and repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 219 218 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON/RUN and the EJECT Button - Ejecting a CD radio ON, the unit will switch from radio to CD mode Press the EJECT button to eject the CD. and begin to play when you insert the disc.
Page 220: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 219 TIME Button Press the SET/RND button a second time to stop Ran- Press this button to change the display from a large CD dom Play. playing time display to a small CD playing time display. Notes On Playing MP3 Files RW/FF The radio can play MP3 files;...
Page 221 220 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal • Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). •...
Page 222 UNDERSTANDING YOUR INSTRUMENT PANEL 221 rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the VBR bit rates.
Page 223: List Button (Cd Mode For Mp3 Play)
222 UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
Page 224: Operating Instructions - Uconnect™ Phone (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 223 TIME Button (Auxiliary Mode) Uconnect™ Multimedia (SATELLITE RADIO) — IF Press this button to change the display to time of day. The EQUIPPED (REN/REQ/RER/RBZ/RES RADIOS time of day will display for five seconds (when the ONLY) ignition is OFF).
Page 225: Electronic Serial Number/Sirius Identification Number (Esn/Sid)
224 UNDERSTANDING YOUR INSTRUMENT PANEL information, call the toll-free number 888-539-7474, or Sirius ID number will display. The Sirius ID number visit the Sirius web site at www.sirius.com, or at www- display will time out in two minutes. Press any button on .siriuscanada.ca for Canadian residents.
Page 226: Reception Quality
UNDERSTANDING YOUR INSTRUMENT PANEL 225 bikes should be placed as far rearward as possible, within Operating Instructions - Uconnect™ Multimedia the loading design of the rack. Do not place items directly (Satellite) Mode on or above the antenna. NOTE: The ignition switch must be in the ON or ACC Reception Quality position to operate the radio.
Page 227 226 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button MUSIC TYPE Button Pressing the INFO button will cycle the display informa- Pressing this button once will turn on the Music Type tion between Artist, Song Title, and Composer (if avail- mode for five seconds. Pressing the MUSIC TYPE button able).
Page 228: Operating Instructions - Uconnect™ Phone (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 227 SETUP Button the SET button twice and SET 2 will show in the display Pressing the SETUP button allows you to select the window. Each button can be set for SET 1 and SET 2. This following items: allows a total of 12 Satellite channels to be stored into pushbutton memory.
Page 229: Remote Sound System Controls - If Equipped
228 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. The left and right controls are rocker-type switches with a pushbutton in the center of each switch.
Page 230: Left-Hand Switch Functions For Radio Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 229 • Press the button located in the center of the switch to Left-Hand Switch Functions for Radio Operation change to the next preset that you have programmed. • Press the top of the switch to SEEK the next listenable station up from the current setting.
Page 231: Radio Operation And Cellular Phones
230 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- Manual Heating and Air Conditioning lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service.
Page 232 UNDERSTANDING YOUR INSTRUMENT PANEL 231 Blower Control Temperature Control Rotate this control to regulate the Rotate this control to regulate the tem- amount of air forced through the ven- perature of the air inside the passenger tilation system in any mode. The compartment.
Page 233 232 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) NOTE: For all settings except full cold or full hot, there Rotate this control to choose from sev- is a difference in temperature between the upper and eral patterns of air distribution. You lower outlets.
Page 234 UNDERSTANDING YOUR INSTRUMENT PANEL 233 Defrost will cause the LED in the control button to illuminate. Air is directed through the windshield and side After ten minutes, the system will return to normal mode window demist outlets. Use this mode with maxi- function and the LED will turn off.
Page 235 234 UNDERSTANDING YOUR INSTRUMENT PANEL • Recirculated air is not allowed in Floor, Mix or Defrost NOTE: The air conditioning compressor will not engage modes. If the Recirculation button is depressed while until the engine has been running for about 10 seconds. in any of these modes, the LED indicator will flash •...
Page 236: Automatic Temperature Control (Atc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Automatic Temperature Control (ATC) — If Equipped NOTE: The AUTO position performs best for front seat occupants only. 2. Dial in the temperature you would like the system to maintain by rotating the Temperature Control knob. Once the comfort level is selected, the sys- tem will maintain that level automati- cally using the heating system.
Page 237 236 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Blower Control • The temperature setting can be adjusted at anytime For full automatic operation or for without affecting automatic operation. automatic blower operation turn the knob to AUTO position. In manual • Pressing the Air Conditioning Control button while in mode there are seven blower speeds AUTO mode will cause the LED in the control button that can be individual selected.
Page 238 UNDERSTANDING YOUR INSTRUMENT PANEL 237...
Page 239 238 UNDERSTANDING YOUR INSTRUMENT PANEL • Floor The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets.
Page 240 UNDERSTANDING YOUR INSTRUMENT PANEL 239 • Air Conditioner Control NOTE: • When the ignition switch is turned to the LOCK Press this button to turn on the air conditioning during manual operation position, the recirculation feature will be cancelled. only. When the air conditioning is •...
Page 241: Operating Tips
240 UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system in air-conditioned vehicles Mode by pressing the Recirculation button. However, must be protected with a high-quality antifreeze coolant under certain conditions, while in Automatic Mode, to provide proper corrosion protection and to protect the system is blowing air out the defrost vents.
Page 242 UNDERSTANDING YOUR INSTRUMENT PANEL 241 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The Mix windshield, is free of obstructions such as leaves.
Page 243 242 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
Page 244: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....247 Key Ignition Park Interlock ... . . 252 Automatic Transmission .
Page 245 244 STARTING AND OPERATING Driving On Slippery Surfaces ... . . 260 Brake Assist System (BAS) ....270 Acceleration .
Page 246 STARTING AND OPERATING 245 Tire Spinning ..... . . 290 3.5L Engine ......304 Tread Wear Indicators .
Page 247 246 STARTING AND OPERATING Selection Of Engine Oil For Flexible Fuel Overloading ......317 Vehicles (E85) And Gasoline Vehicles ..312 Loading .
Page 248: Starting Procedures
STARTING AND OPERATING 247 STARTING PROCEDURES NOTE: The ignition switch must be in the ON position, Before starting your vehicle, adjust your seat, adjust the and you must press the brake pedal before shifting out of inside and outside mirrors, fasten your seat belt, and if PARK.
Page 249: Extreme Cold Weather (Below 20°F Or 29°C)
248 STARTING AND OPERATING motor will continue to run, and it will disengage auto- WARNING! (Continued) matically when the engine is running. If the engine fails • Do not attempt to push or tow your vehicle to get to start, the starter will disengage automatically in 10 sec- it started.
Page 250: After Starting
STARTING AND OPERATING 249 the way to the floor and hold it there while cranking the With Tip Start engine. This should clear any excess fuel in case the If the engine fails to start after you have followed the engine is flooded.
Page 251: Engine Block Heater - If Equipped
250 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine, and permits CAUTION! quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a Damage to the transmission may occur if the follow- grounded, three-wire extension cord.
Page 252 STARTING AND OPERATING 251 WARNING! • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
Page 253: Key Ignition Park Interlock
252 STARTING AND OPERATING can only be removed from the ignition when the ignition WARNING! (Continued) is in the LOCK position and once removed the shift lever • Unintended movement of a vehicle could injure is locked in PARK. those in and near the vehicle. As with all vehicles, Brake/Transmission Interlock System you should never exit a vehicle while the engine is This vehicle is equipped with a Brake Transmission Shift...
Page 254: Automatic Transmission Ignition Interlock System
STARTING AND OPERATING 253 • Insert the ignition key into the ignition switch and Automatic Transmission Ignition Interlock System rotate it to the ON position. This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of •...
Page 255: Gear Ranges
254 STARTING AND OPERATING Gear Ranges WARNING! PARK • Never use the PARK position as a substitute for This range supplements the parking brake by locking the the parking brake. Always apply the parking transmission. The engine can be started in this range. brake fully when parked to guard against vehicle Never attempt to use PARK while vehicle is in motion.
Page 256 STARTING AND OPERATING 255 REVERSE DRIVE – Six-Speed Transmission This range is for moving the vehicle backward. Use only This range should be used for most city and highway after the vehicle has come to a complete stop. driving. It provides the smoothest upshifts, downshifts, and best fuel economy.
Page 257 256 STARTING AND OPERATING under heavy loading conditions, (i.e., in hilly terrain, gear operation at higher speeds. The 3 range should traveling into strong headwinds, or while towing heavy also be used when descending steep grades to prevent trailers). Under these conditions, using the 3 range will brake system distress improve performance and extend transmission life by NOTE: Using the 3 range while operating the vehicle...
Page 258 STARTING AND OPERATING 257 the forward gear selected. PARK, REVERSE, and NEU- CAUTION! TRAL will continue to operate. The Reset feature allows the vehicle to be driven to a dealer for service without If the transmission operating temperature exceeds damaging the transmission. acceptable limits, the vehicle computer will override DRIVE (OVERDRIVE) and [5] for six–speed In the event of a momentary problem, the transmission...
Page 259: Autostick - If Equipped
258 STARTING AND OPERATING NOTE: Even if the transmission can be reset, it is Operation recommended that you visit a dealer at your earliest By placing the shift lever one shift-level below the DRIVE possible convenience. Your dealer has diagnostic equip- position, it can be moved from side to side.
Page 260: General Information
STARTING AND OPERATING 259 • If a low range is selected and the engine accelerates to General Information the rev limit, the transmission will automatically select • You can start out, from a stop, in any gear except sixth. the next higher ratio. The system will ignore attempts to upshift at too low •...
Page 261: Acceleration
260 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 262: Driving Through Water
STARTING AND OPERATING 261 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle.
Page 263 262 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 264: Power Steering
STARTING AND OPERATING 263 POWER STEERING system. This noise should be considered normal, and it The standard power steering system will give you good does not in any way damage the steering system. vehicle response and increased ease of maneuverability WARNING! in tight spaces.
Page 265: Power Steering Fluid Check
264 STARTING AND OPERATING Power Steering Fluid Check WARNING! Checking the power steering fluid level at a defined service interval is not required. The fluid should only be Fluid level should be checked on a level surface and checked if a leak is suspected, abnormal noises are with the engine off to prevent injury from moving apparent, and/or the system is not functioning as antici- parts and to ensure accurate fluid level reading.
Page 266 STARTING AND OPERATING 265 The parking brake lever is located in the center console. When the parking brake is applied with the ignition To apply the parking brake, pull the lever up as firmly as switch ON, the “Brake Warning Light” in the instrument possible.
Page 267 266 STARTING AND OPERATING make it difficult to move the shift lever out of PARK. The WARNING! (Continued) parking brake should always be applied whenever the • Be sure the parking brake is fully disengaged driver is not in the vehicle. before driving;...
Page 268: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 267 ANTI-LOCK BRAKE SYSTEM (ABS) WARNING! (Continued) The Anti-Lock Brake System (ABS) provides increased • The ABS cannot prevent the natural laws of phys- vehicle stability and brake performance under most ics from acting on the vehicle, nor can it increase braking conditions.
Page 269 268 STARTING AND OPERATING The “Anti-Lock Brake Warning Light” moni- (ABS) and Electronic Brake Force Distribution (EBD) tors the Anti-Lock Brake System. The light will Systems are not functioning. Immediate repair to the ABS come on when the ignition switch is turned to system is required.
Page 270: Electronic Brake Control System
STARTING AND OPERATING 269 • the clicking sound of solenoid valves, All vehicle wheels and tires must be the same size and type, and tires must be properly inflated to produce • brake pedal pulsations, accurate signals for the computer. •...
Page 271: Traction Control System (Tcs)
270 STARTING AND OPERATING help avoid skidding on slippery surfaces during braking. Brake Assist System (BAS) Refer to “Anti-Lock Brake System” in “Starting and The BAS is designed to optimize the vehicle’s braking Operating” for further information. capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- Traction Control System (TCS) ing the rate and amount of brake application and then...
Page 272: Hill Start Assist (Hsa) - If Equipped
STARTING AND OPERATING 271 Hill Start Assist (HSA) – If Equipped WARNING! The HSA system is designed to assist the driver in • The BAS cannot prevent the natural laws of phys- launching a vehicle on an incline. HSA will maintain the level of brake pressure the driver inputs for a short ics from acting on the vehicle, nor can it increase duration once the driver takes his foot off of the brake...
Page 273 272 STARTING AND OPERATING HSA Activation Criteria The system will only work if the intended direction of the The following criteria must be met in order for HSA to vehicle and vehicle gear match. For example, if the activate: intended direction is forward up a hill and the vehicle is in DRIVE and the activation criteria are met, HSA will •...
Page 274: Electronic Stability Control (Esc)
STARTING AND OPERATING 273 2. Shift the transmission into NEUTRAL. 10. Repeat these steps if you want to return this feature to it’s previous setting. 3. Apply the parking brake. EVIC Equipped Vehicles 4. Start the engine. HSA is a Customer Programmable Feature on a EVIC 5.
Page 275 274 STARTING AND OPERATING path does not match the intended path, ESC applies the WARNING! brake of the appropriate wheel to assist in counteracting • The Electronic Stability Control (ESC) cannot pre- the oversteer or understeer condition vent the natural laws of physics from acting on the •...
Page 276 STARTING AND OPERATING 275 • The ESC system will make buzzing or clicking sounds ESC Malfunction Indicator Light The “ESC Malfunction Indicator Light” in the when it is active. This is normal; the sounds will stop instrument cluster will come on when the when ESC becomes inactive following the maneuver ignition switch is turned to the ON position.
Page 277 276 STARTING AND OPERATING feature described in the TCS section, has been disabled NOTE: To improve the vehicle’s traction when driving and the “ESC Off Indicator Light” will be illuminated. All with snow chains, or starting off in deep snow, sand or other stability features of ESC function normally, with the gravel, it may be desirable to switch to the “Partial Off”...
Page 278: Tire Safety Information
STARTING AND OPERATING 277 TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 279 278 STARTING AND OPERATING • High flotation tire sizing is based on U.S. design Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- standards and it begins with the tire diameter molded tion.
Page 280 STARTING AND OPERATING 279 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 281: Tire Identification Number (Tin)
280 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 282: Tire Terminology And Definitions
STARTING AND OPERATING 281 Tire Terminology and Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 283: Tire Loading And Tire Pressure
282 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle...
Page 284 STARTING AND OPERATING 283 Loading The combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
Page 285 284 STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs NOTE: • The following table shows examples on how to calcu- (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations 5.
Page 286 STARTING AND OPERATING 285...
Page 287: Tires - General Information
286 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 288: Tire Inflation Pressures
STARTING AND OPERATING 287 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side B-Pillar. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 289 288 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the winter.
Page 290: Radial-Ply Tires
STARTING AND OPERATING 289 Tire Pressures for High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 291: Tire Spinning
290 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a WARNING! conventional tire on the compact spare wheel since the wheel is designed specifically for the compact spare. Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph Do not install more than one compact spare tire/wheel (80 km/h).
Page 292: Tread Wear Indicators
STARTING AND OPERATING 291 Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one.
Page 293: Life Of Tire
292 STARTING AND OPERATING Life of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors including but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 294 STARTING AND OPERATING 293 WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 295: Tire Chains
294 STARTING AND OPERATING TIRE CHAINS Snow tires generally have lower speed ratings than what Due to limited clearance, tire chains are not recom- was originally equipped with your vehicle and should mended. not be operated at sustained speeds over 75 mph (120 km/h).
Page 296: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 295 desired. The reasons for any rapid or unusual wear TIRE PRESSURE MONITOR SYSTEM (TPMS) should be corrected prior to rotation being performed. The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recom- The suggested rotation method is shown in the following mended cold placard pressure.
Page 297 296 STARTING AND OPERATING The TPM System will warn the driver of a low tire For example, your vehicle may have a recommended pressure if the tire pressure falls below the low-pressure cold (parked for more than three hours) placard pressure warning limit for any reason, including low temperature of 30 psi (207 kPa).
Page 298 STARTING AND OPERATING 297 NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance, or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures and warning have been established for the tire size •...
Page 299: Base System
298 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings and the TPMS will monitor the actual tire pressure in The “Tire Pressure Monitoring Telltale Light” will the tire. illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or Base System more of the four active road tires.
Page 300 STARTING AND OPERATING 299 will repeat, providing the system fault still exists. The NOTE: “Tire Pressure Monitoring Telltale Light” will turn off 1. The compact spare tire (if so equipped) does not have when the fault condition no longer exists. A system fault a tire pressure monitoring sensor.
Page 301: Premium System - If Equipped
300 STARTING AND OPERATING 5. Once you repair or replace the original road tire, and The TPMS consists of the following components: reinstall it on the vehicle in place of the compact spare, • Receiver Module the TPMS will update automatically and the “TPM •...
Page 302 STARTING AND OPERATING 301 Electronic Vehicle Information Center (EVIC) will display Should this occur, you should stop as soon as possible, a graphic showing the pressure values of each tire with and inflate all tires with low pressure (those flashing in the low tire pressure values flashing.
Page 303 302 STARTING AND OPERATING Check TPMS Warning If the ignition key is cycled, this sequence will repeat, When a system fault is detected, a chime will sound and providing the system fault still exists. If the system fault the “Tire Pressure Monitoring Telltale Light” will flash on no longer exists, the “Tire Pressure Monitoring Telltale and off for 75 seconds and then remain on solid.
Page 304 STARTING AND OPERATING 303 NOTE: 4. For each subsequent ignition key cycle, a chime will 1. The compact spare tire (if so equipped) does not have sound, the “TPM Telltale Light” will flash on and off for a tire pressure monitoring sensor. Therefore, the TPMS 75 seconds and then remain on solid, and the EVIC will will not monitor the pressure in the compact spare tire.
Page 305: General Information
304 STARTING AND OPERATING General Information FUEL REQUIREMENTS This device complies with part 15 of the FCC rules and 2.4L and 2.7L Engine RSS 210 of Industry Canada. Operation is subject to the All engines are designed to meet all emis- following conditions: sion regulations and provide excellent fuel •...
Page 306: Reformulated Gasoline
STARTING AND OPERATING 305 for optimum performance. The use of premium gasoline vehicle. The manufacturer recommends the use of gaso- is not recommended, as it will not provide any benefit lines that meet the WWFC specifications if they are over regular gasoline in these engines. available.
Page 307: E-85 Usage In Non-Flex Fuel Vehicles
306 STARTING AND OPERATING winter months to reduce carbon monoxide emissions. manufacturer. While MTBE is an oxygenate made from Fuels blended with these oxygenates may be used in Methanol, it does not have the negative effects of your vehicle. Methanol. E-85 Usage In Non-Flex Fuel Vehicles CAUTION! Non-FFV vehicles are compatible with gasoline contain-...
Page 308: Mmt In Gasoline
STARTING AND OPERATING 307 To fix a Non-FFV vehicle inadvertently fueled once with of gasoline may not be indicated on the gasoline pump, E-85 perform the following: therefore, you should ask your gasoline retailer whether or not his/her gasoline contains MMT. •...
Page 309: Fuel System Cautions
308 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
Page 310: Carbon Monoxide Warnings
STARTING AND OPERATING 309 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 311: Flexible Fuel (2.7L Only) - If Equipped
310 STARTING AND OPERATING FLEXIBLE FUEL (2.7L ONLY) — IF EQUIPPED E85 General Information The information in this section is for Flexible Fuel ve- hicles only. These vehicles can be identified by a unique fuel filler door label that states Ethanol (E85) or Un- leaded Gasoline Only.
Page 312: Ethanol Fuel (E85)
STARTING AND OPERATING 311 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
Page 313: Selection Of Engine Oil For Flexible Fuel Vehicles (E85) And Gasoline Vehicles
These special requirements are included during warm up. in MOPAR engine oils, and in equivalent oils meeting Chrysler Specification MS-6395. The manufacturer only NOTE: recommends engine oils that are API Certified and meet • Use seasonally adjusted E85 fuel (ASTM D5798). With the requirements of Material Standard MS-6395.
Page 314: Starting
STARTING AND OPERATING 313 Starting Replacement Parts The characteristics of E85 fuel make it unsuitable for use Many components in your Flexible Fuel Vehicle (FFV) are when ambient temperatures fall below 0°F (-18°C). In the designed to be compatible with ethanol. Always be sure range of 0°F (-18°C) to 32°F (0°C), you may experience an that your vehicle is serviced with correct ethanol com- increase in the time it takes for your engine to start, and...
Page 315: Adding Fuel
314 STARTING AND OPERATING ADDING FUEL After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the Fuel Filler Cap (Gas Cap) gas cap suspended away from and protects the vehicle’s The gas cap is behind the fuel filler door, on the left rear surface.
Page 316 STARTING AND OPERATING 315 CAUTION! WARNING! (Continued) • Never add fuel when the engine is running. This is • Damage to the fuel system or emission control in violation of most state and federal fire regula- system could result from using an improper fuel tions and doing so will cause the MIL to turn on.
Page 317: Loose Filler Cap Message
316 STARTING AND OPERATING • Name of manufacturer Loose Filler Cap Message If the vehicles diagnostic system determines that the fuel • Month and year of manufacture filler cap in loose, improperly installed, or damaged, a • Gross Vehicle Weight Rating (GVWR) “gASCAP”...
Page 318: Gross Axle Weight Rating (Gawr)
STARTING AND OPERATING 317 Gross Axle Weight Rating (GAWR) The best way to figure out the total weight of your The GAWR is the maximum capacity of the front and rear vehicle is to weigh it when it is fully loaded and ready for axles.
Page 319: Trailer Towing
318 STARTING AND OPERATING the specified GVWR, you must redistribute the weight. Common Towing Definitions Improper weight distribution can have an adverse effect The following trailer towing related definitions will assist on the way your vehicle steers and handles and the way you in understanding the following information: the brakes operate.
Page 320: Trailer Hitch Classification
STARTING AND OPERATING 319 Gross Combination Weight Rating (GCWR) Trailer Tongue Weight (TW) The GCWR is the total permissible weight of your vehicle The tongue weight is the downward force exerted on the and trailer when weighed in combination. hitch ball by the trailer. In most cases it should not be less than or more than 10% of the trailer load.
Page 321 320 STARTING AND OPERATING tow and should be used to assist you in selecting the Trailer Hitch Classification Definitions correct trailer hitch for your intended towing condition. Class Max. Trailer Hitch Industry Refer to the Trailer Towing Weights (Maximum Trailer Standards Weight Ratings) chart for the Max.
Page 322: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 321 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum Trailer Weight Ratings Max. GTW Max. Trailer Tongue Wt. Engine/Transmission Max. Frontal Area (Gross Trailer Wt.) (See Note 1) 2.4L/Auto See Note 2...
Page 323: Trailer And Tongue Weight
322 STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme condi- tions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
Page 324: Towing Requirements
STARTING AND OPERATING 323 NOTE: Remember that everything put into or on the Towing Requirements trailer adds to the load on your vehicle. Also, additional To promote proper break-in of your new vehicle drive- factory-installed options, or authorized dealer-installed train components the following guidelines are recom- options, must be considered as part of the total load on mended: your vehicle.
Page 325 324 STARTING AND OPERATING WARNING! WARNING! (Continued) • Safety chains must always be used between your Improper towing can lead to an injury accident. vehicle and trailer. Always connect the chains to Follow these guidelines to make your trailer towing the frame or hook retainers of the vehicle hitch.
Page 326 STARTING AND OPERATING 325 • Check for signs of tire wear or visible tire damage WARNING! (Continued) before towing a trailer. Refer to “Tires – General 3. GAWR Information” in “Starting and Operating” for informa- 4. Trailer tongue weight rating for the trailer hitch tion on tread wear indicators and for proper inspection utilized (This requirement may limit the ability to procedure.
Page 327 326 STARTING AND OPERATING • An electronically actuated trailer brake controller is WARNING! required when towing a trailer with electronically • Do not connect trailer brakes to your vehicle’s actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic hydraulic brake lines.
Page 328: Towing Tips
STARTING AND OPERATING 327 Towing Tips If you REGULARLY TOW a trailer for more than 45 min- Before setting out on a trip, practice turning, stopping, utes of continuous operation, then change the automatic and backing the trailer in an area located away from transmission fluid and filter according to the interval heavy traffic.
Page 329: Recreational Towing (Behind Motorhome, Etc.)
328 STARTING AND OPERATING • Use speed control in flat terrain and with light loads to RECREATIONAL TOWING (BEHIND maximize fuel efficiency. MOTORHOME, ETC.) Cooling System Towing This Vehicle Behind Another Vehicle (Flat To reduce potential for engine and transmission over- towing with all four wheels on the ground) heating, take the following actions: CAUTION!
Page 330: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....330 Jump-Starting ......339 If Your Engine Overheats .
Page 331: Hazard Warning Flasher
330 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate action. •...
Page 332: Engine Oil Overheating - 2.4L Engine Only (If Equipped)
WHAT TO DO IN EMERGENCIES 331 NOTE: There are steps that you can take to slow down Engine Oil Overheating — 2.4L Engine Only (If an impending overheat condition: Equipped) During sustained high-speed driving or trailer tow up • If your air conditioner (A/C) is on, turn it off. The A/C long grades on hot day, the engine oil temperature may system adds heat to the engine cooling system and become too hot.
Page 333: Jacking And Tire Changing
332 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) • The jack is designed to use as a tool for changing WARNING! tires only. The jack should not be used to lift the • Do not attempt to change a tire on the side of the vehicle for service purposes.
Page 334: Jack Location
WHAT TO DO IN EMERGENCIES 333 6. Block both the front and rear of the Spare Tire Removal wheel diagonally opposite the jacking Lift up the load floor cover and remove the hold down. position. For example, if changing the right front tire, block the left rear wheel.
Page 335: Jacking Instructions
334 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. Carefully follow these tire changing warnings to • Do not get under the vehicle when it is on a jack. help prevent personal injury or damage to your •...
Page 336 WHAT TO DO IN EMERGENCIES 335 Jack Warning Label 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly.
Page 337 336 WHAT TO DO IN EMERGENCIES Jacking Locations...
Page 338 WHAT TO DO IN EMERGENCIES 337 head is properly engaged with the lift area closest to the CAUTION! wheel to be changed. Do not raise the vehicle until you are sure the jack is securely engaged. Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 3.
Page 339 338 WHAT TO DO IN EMERGENCIES toward the wheel. Lightly tighten the nuts. To avoid the tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered.
Page 340: Jump-Starting
WHAT TO DO IN EMERGENCIES 339 JUMP-STARTING Preparations for Jump-Start If your vehicle has a discharged battery it can be jump- The battery in your vehicle is located between the left started using a set of jumper cables and a battery in front headlight assembly and the left front wheel splash another vehicle or by using a portable battery booster shield.
Page 341 340 WHAT TO DO IN EMERGENCIES 3. Remove the protective cover over the remote positive WARNING! (+) battery post. To remove the cover, press the locking • Take care to avoid the radiator cooling fan when- tab and pull upward on the cover. ever the hood is raised.
Page 342: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 341 1. Connect the positive (+) end of the jumper cable to the WARNING! remote positive (+) post of the discharged vehicle. Do not allow vehicles to touch each other as this 2. Connect the opposite end of the positive (+) jumper could establish a ground connection and personal cable to the positive (+) post of the booster battery.
Page 343: Freeing A Stuck Vehicle
342 WHAT TO DO IN EMERGENCIES 5. Start the engine in the vehicle that has the booster 10. Reinstall the protective cover over the remote posi- battery, let the engine idle a few minutes, and then start tive (+) battery post of the discharged vehicle. the engine in the vehicle with the discharged battery.
Page 344 WHAT TO DO IN EMERGENCIES 343 front wheels. Then shift back and forth between RE- CAUTION! (Continued) VERSE and FIRST gear. Using minimal accelerator pedal • Revving the engine or spinning the wheels too fast pressure to maintain the rocking motion, without spin- may lead to transmission overheating and failure.
Page 345: Towing A Disabled Vehicle
344 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE CAUTION! (Continued) With The Ignition Key • If the transaxle is not operative, or if the vehicle is Your vehicle may be towed under the following condi- to be towed more than 15 miles (25 km), the tions: vehicle must be transported either with a flatbed truck (all four wheels off the ground) or with the...
Page 346: Without The Ignition Key
WHAT TO DO IN EMERGENCIES 345 If you must use the accessories (wipers, defrosters, etc.) while being towed, the key must be in the ON position, not the ACC position. Make certain the transaxle remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position.
Page 348: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 2.4L ... . . 349 Maintenance Procedures ....355 Engine Compartment —...
Page 349 348 MAINTAINING YOUR VEHICLE Adding Washer Fluid ....366 Replacement Bulbs ....394 Exhaust System .
Page 350: Engine Compartment - 2.4L
MAINTAINING YOUR VEHICLE 349 ENGINE COMPARTMENT — 2.4L 1 — Engine Coolant Reservoir 7 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 8 — Engine Oil Fill 3 — Automatic Transmission Dipstick 9 — Coolant Pressure Cap 4 — Brake Fluid Reservoir 10 —...
Page 351: Engine Compartment - 2.7L
350 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.7L 1 — Engine Coolant Reservoir 7 — Power Distribution Center 2 — Coolant Pressure Cap 8 — Air Cleaner Filter 3 — Power Steering Fluid Reservoir 9 — Engine Oil Dipstick 4 — Automatic Transmission Dipstick (Four-Speed Only) 10 —...
Page 352: Engine Compartment - 3.5L
MAINTAINING YOUR VEHICLE 351 ENGINE COMPARTMENT — 3.5L 1 — Engine Coolant Reservoir 6 — Air Cleaner Filter 2 — Coolant Pressure Cap 7 — Engine Oil Dipstick 3 — Power Steering Fluid Reservoir 8 — Engine Oil Fill 4 — Brake Fluid Reservoir 9 —...
Page 353: Onboard Diagnostic System - Obd Ii
352 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated Onboard • Prolonged driving with the “Malfunction Indica- Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic tor Light”...
Page 354: Emissions Inspection And Maintenance Programs
MAINTAINING YOUR VEHICLE 353 the gas cap is properly tightened. Press the trip odometer Normally, the OBD II system will be ready. The OBD II “Reset” button to turn off the message. If the problem system may not be ready if your vehicle was recently persists, the message will appear the next time the serviced, recently had a dead battery or a battery replace- vehicle is started.
Page 355: Replacement Parts
354 MAINTAINING YOUR VEHICLE 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a.
Page 356: Maintenance Procedures
Only do service work for which you mance. Immediately have potential malfunctions have the knowledge and the proper equipment. If examined by an authorized Chrysler Group LLC you have any doubt about your ability to perform a dealership or qualified repair center.
Page 357: Engine Oil
356 MAINTAINING YOUR VEHICLE fully warmed engine is shut off. Do not check oil level CAUTION! (Continued) before starting the engine after it has sat overnight. • Your vehicle has been built with improved fluids Checking engine oil level when the engine is cold will that protect the performance and durability of give you an incorrect reading.
Page 358 Do not overfill the engine. Overfilling the engine mends engine oils that are API Certified and meet the will cause oil aeration, which can lead to loss of oil requirements of Chrysler Material Standard MS-6395. pressure and an increase in oil temperature. This could damage your engine.
Page 359 358 MAINTAINING YOUR VEHICLE Lubricants which do not have both the engine oil certi- CAUTION! fication mark and the correct SAE viscosity grade num- ber should not be used. Do not use chemical flushes in your engine oil as the chemicals can damage your engine.
Page 360: Engine Oil Filter
MAINTAINING YOUR VEHICLE 359 Lubricants which do not have both the engine oil certi- environment. Contact your authorized dealer, service fication mark and the correct SAE viscosity grade num- station, or governmental agency for advice on how and ber should not be used. where used oil and oil filters can be safely discarded in your area.
Page 361: Engine Air Cleaner Filter
360 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter used to assure most efficient service. MOPAR engine air cleaner filters are high quality and are recommended. WARNING! Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. The air induction system (air cleaner, hoses, etc.) can You will never have to add water, nor is periodic main- provide a measure of protection in the case of engine tenance required.
Page 362 MAINTAINING YOUR VEHICLE 361 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 363: Air Conditioner Maintenance
362 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an authorized dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 364: A/C Air Filter - If Equipped
MAINTAINING YOUR VEHICLE 363 Refrigerant Recovery and Recycling The A/C Air Filter is located in the fresh air inlet behind R-134a air conditioning refrigerant is a hydrofluoro- the glove box. Perform the following procedure to re- carbon (HFC) that is endorsed by the Environmental place the filter: Protection Agency and is an ozone-saving product.
Page 365: Body Lubrication
364 MAINTAINING YOUR VEHICLE 5. Disengage the two retaining tabs that secure the filter 7. Install the A/C Air Filter with the arrow on the filter cover to the HVAC housing and remove the cover. pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover.
Page 366: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 365 concerned should be wiped clean to remove dust and Operation of the wipers on dry glass for long periods grit; after lubricating excess oil and grease should be may cause deterioration of the wiper blades. Always use removed.
Page 367: Exhaust System
366 MAINTAINING YOUR VEHICLE Adding Washer Fluid Exhaust System The fluid reservoir for the windshield washers is located The best protection against carbon monoxide entry into in the engine compartment. Be sure to check the fluid the vehicle body is a properly maintained engine exhaust level in the reservoir at regular intervals.
Page 368 MAINTAINING YOUR VEHICLE 367 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions con- and can eventually poison you.
Page 369 368 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 370: Cooling System
MAINTAINING YOUR VEHICLE 369 Cooling System rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (anti- WARNING! freeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently •...
Page 371 370 MAINTAINING YOUR VEHICLE Selection Of Coolant CAUTION! (Continued) Use only the manufacturer’s recommended coolant. Re- • Do not use water alone or alcohol-based engine fer to “Fluids, Lubricants, and Genuine Parts” in “Main- coolant (antifreeze) products. Do not use addi- taining Your Vehicle”...
Page 372 MAINTAINING YOUR VEHICLE 371 replacement. To prevent reducing this extended mainte- (antifreeze) solution. The use of lower quality water nance period, it is important that you use the same will reduce the amount of corrosion protection in the engine coolant (antifreeze) throughout the life of your engine cooling system.
Page 373 372 MAINTAINING YOUR VEHICLE rules for your community. To prevent ingestion by ani- WARNING! mals or children, do not store ethylene glycol based • The warning words “DO NOT OPEN HOT” on engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground.
Page 374 MAINTAINING YOUR VEHICLE 373 The radiator normally remains completely full, so there is If an examination of your engine compartment shows no no need to remove the radiator cap unless checking for evidence of radiator or hose leaks, the vehicle may be engine coolant (antifreeze) freeze point or replacing cool- safely driven.
Page 375: Brake System
374 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery WARNING! bottle overflow hoses are not kinked or obstructed. Riding the brakes can lead to brake failure and • Keep the front of the radiator clean. If your vehicle is possibly an accident.
Page 376 MAINTAINING YOUR VEHICLE 375 Clean the top of the master cylinder area before removing WARNING! the cap. If necessary, add fluid to bring the fluid level up • Use only manufacturer’s recommended brake to the requirements described on the brake fluid reser- voir.
Page 377: Automatic Transmission
376 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
Page 378 MAINTAINING YOUR VEHICLE 377 Fluid Level Check – 2.4L and 2.7L Engines driven at least 15 miles (24 km). Hot fluid cannot be held Use the following procedure to check the automatic comfortably between the fingertips. Cold fluid is at a transmission fluid level properly: temperature below 80°F (27°...
Page 379 378 MAINTAINING YOUR VEHICLE Fluid Level Check – 3.5L Engine CAUTION! The automatic transmission has no dipstick and is dealer • Using a transmission fluid other than the manu- serviced only. facturer’s recommended fluid may cause deterio- Transmission Fluid and Filter Changes ration in transmission shift quality and/or torque Refer to “Maintenance Schedule”...
Page 380: Appearance Care And Protection From Corrosion
MAINTAINING YOUR VEHICLE 379 The following maintenance recommendations will enable CAUTION! you to obtain maximum benefit from the corrosion resistance built into your vehicle. Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- What Causes Corrosion? nents.
Page 381 380 MAINTAINING YOUR VEHICLE Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- • Do not use abrasive or strong cleaning materials hicle in the shade using MOPAR Car Wash or equiva- such as steel wool or scouring powder, which will lent, or a mild car wash soap, and rinse the panels scratch metal and painted surfaces.
Page 382 MAINTAINING YOUR VEHICLE 381 • If you detect any stone chips or scratches in the paint, Wheel and Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and considered the responsibility of the owner. chrome-plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 383 382 MAINTAINING YOUR VEHICLE • For grease stains, apply MOPAR To minimize the possibility of scratching the lenses and Multi-Purpose reducing light output, avoid wiping with a dry cloth. To Cleaner or equivalent to a clean, damp cloth and remove road dirt, wash with a mild soap solution fol- remove the stain.
Page 384 MAINTAINING YOUR VEHICLE 383 if absolutely necessary. Do not use harsh cleaners or WARNING! Armor All . Use MOPAR Total Clean or equivalent to clean vinyl upholstery. Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in Cleaning Leather Upholstery closed areas they may cause respiratory harm.
Page 385: Cleaning Center Console Cupholders
384 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses Replace the belts if they appear frayed or worn or if the The lenses in front of the instruments in this vehicle are buckles do not work properly. molded in clear plastic. When cleaning the lenses, care Dry with a soft tissue.
Page 386: Convertible Top Care
MAINTAINING YOUR VEHICLE 385 Installation CAUTION! (Continued) Align the liner in the cupholder and press down firmly. • Use care when washing the vehicle, water pressure Convertible Top Care directed at the weather strip seals may cause water to leak into the vehicles interior. CAUTION! Immediate removal of any contaminant is recommended.
Page 387 386 MAINTAINING YOUR VEHICLE Washing CAUTION! Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you Never use an abrasive type cleaner or bleaches. must use an automatic car wash, soft cloth systems are Cleaners should not contain silicones, organic sol- preferred.
Page 388: Weather Strip Care - Soft And Hard Top
MAINTAINING YOUR VEHICLE 387 Additional Cleaning Procedure CAUTION! For additional cleaning assistance in removing stubborn stains, apply MOPAR Convertible Cloth Top Cleaner or Avoid getting Scotchguard on the surrounding equivalent to the complete stain, extending 2 inches weather strips, moldings, paint, or glass. Damage to (50 mm) beyond the stain.
Page 389: Fuses
388 MAINTAINING YOUR VEHICLE FUSES Totally Integrated Power Module (TIPM) The TIPM is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location.
Page 390 MAINTAINING YOUR VEHICLE 389 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 40 Amp Power Top Mod- 30 Amp Ignition Off Draw — — Green ule – If Equipped Green (IOD) Sense 1 20 Amp 30 Amp Ignition Off Draw —...
Page 391 390 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 20 Amp Ignition Off Draw — — Yellow (IOD) – Wireless 10 Amp Control Module Ignition Off Draw — (WCM)/Clock/ (IOD) – Cabin 10 Amp Steering Control —...
Page 392 MAINTAINING YOUR VEHICLE 391 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Ignition Run – Ignition Run – 10 Amp Climate Controls/ Occupant Classifi- — Hot Cupholder – 10 Amp cation Module — If Equipped (OCM)/Occupant Restraint Control- Auto Shutdown 15 Amp...
Page 393 392 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 10 Amp Battery Feed – — — Anti-Lock Brakes (ABS) Module – If Auto Shutdown 30 Amp 30 Amp Equipped/ — (ASD) Relay Feed —...
Page 394: Vehicle Storage
MAINTAINING YOUR VEHICLE 393 Cartridge Mini CAUTION! (Continued) Cavity Description Fuse Fuse • When replacing a blown fuse, it is important to Battery Feed – use only a fuse having the correct amperage rating. Passenger Door 30 Amp The use of a fuse with a rating other than indicated —...
Page 395: Replacement Bulbs
394 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS Center High Mounted Stop Lamp All the inside bulbs are brass or glass wedge base. (CHMSL) ......W16W (921) Aluminum base bulbs are not approved and should not Rear Tail/Stop Lamp .
Page 396 MAINTAINING YOUR VEHICLE 395 2. Reach into engine compartment and from behind the 3. Rotate bulb and connector one-quarter turn and pull lamp assembly and grasp the connector. outward from assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
Page 397: Front Turn Signal/Parking Lamp
396 MAINTAINING YOUR VEHICLE 4. Pull the bulb out of the socket and replace the bulb. Front Turn Signal/Parking Lamp 1. Raise and prop open the hood. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the headlamp housing.
Page 398: Front Fog Lamp
MAINTAINING YOUR VEHICLE 397 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlamp housing and rotate the connector one-quarter turn clockwise to lock it in place. Front Fog Lamp NOTE: Access to the lamps through the lower fascia cutout is limited.
Page 399: Tail/Stop, Rear Turn Signal And Backup Lamps
398 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Install the bulb and connector assembly into the fog lamp housing and rotate the connector one-quarter turn clockwise to lock it in place.
Page 400 MAINTAINING YOUR VEHICLE 399 Changing the Tail/Stop Lamp or Rear Turn Signal Lamp 1. Open the trunk and gently pull back the trunk liner behind the taillamp 3. Grasp the taillamp housing and pull it firmly outward while pushing gently on the studs from inside to disen- gage the housing from the vehicle.
Page 401 400 MAINTAINING YOUR VEHICLE 4. Rotate the applicable bulb’s electrical connector one- 5. Remove the bulb from the connector socket and install quarter turn counterclockwise and remove it from the the replacement bulb. taillamp housing. 6. Install the bulb and connector assembly into the taillamp housing and rotate the connector one-quarter turn clockwise to lock it in place.
Page 402: License Plate Lamp
MAINTAINING YOUR VEHICLE 401 License Plate Lamp 1. Remove two retaining screws holding the lamp lens in place. 1 — Rear Fog Lamp 2 — Backup Lamp 3. Remove the bulb from the connector socket and install the replacement bulb. 2.
Page 403: Center High-Mounted Stop Lamp (Chmsl)
402 MAINTAINING YOUR VEHICLE Center High-Mounted Stop Lamp (CHMSL) 3. Remove the bulb from the connector socket and install the replacement bulb. 1. Open the trunk lid. 4. Install the bulb and connector assembly into the 2. Rotate the bulb’s electrical connector one-quarter turn CHMSL housing and rotate the connector one-quarter counterclockwise and remove it from the CHMSL hous- turn clockwise to lock it in place.
Page 404: Fluid Capacities
MAINTAINING YOUR VEHICLE 403 FLUID CAPACITIES U.S. Metric Fuel (Approximate) All Engines 16.9 Gallons 64 Liters Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 4.4 Liters 2.7L Engine (SAE 5W-20, API Certified) 5.5 Quarts 5.2 Liters 3.5L Engine (SAE 10W-30, API Certified) 5.5 Quarts 5.2 Liters...
Page 405: Fluids, Lubricants, And Genuine Parts
Engine Oil – 2.4L and 2.7L Engines filler cap for correct SAE grade. Use API Certified SAE 10W-30 Engine Oil, meeting Chrysler Mate - rial Standard MS-6395. Refer to your engine oil filler cap for correct Engine Oil – 3.5L Engine SAE grade.
Page 406: Chassis
MAINTAINING YOUR VEHICLE 405 Chassis Component Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed Automatic Transmission ATF+4 product. MOPAR DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is Brake Master Cylinder not available, then DOT 4 is acceptable.
Page 408 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..408 Required Maintenance Intervals ..410 Maintenance Schedule ....408...
Page 409 408 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the emissions control On Electronic Vehicle Information Center (EVIC) system.
Page 410 MAINTENANCE SCHEDULES 409 NOTE: “Understanding Your Instrument Panel” or under “In- • The oil change indicator message will not monitor the strument Cluster Description/Odometer/Trip Odom- time since the last oil change. Change your vehicles oil eter” in “Understanding Your Instrument Panel” for if it has been 6 months since your last oil change even further information.
Page 411 410 MAINTENANCE SCHEDULES Once a Month CAUTION! • Check tire pressure and look for unusual wear or Failure to perform the required maintenance items damage. may result in damage to the vehicle. • Inspect the battery and clean and tighten the terminals as required.
Page 412 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 413: Service Schedule
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 414 Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 415 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 416 ❏ Adjust parking brake on vehicles equipped with four wheel disc brakes. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 417 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 418 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 419 Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 420 ❏ Inspect accessory drive belt, replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 421 ❏ Change the automatic transmission fluid & filter. ❏ Adjust parking brake on vehicles equipped with four wheel disc brakes. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 422 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 423 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 424 • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This Odometer Reading Date could cause an accident Repair Order # Dealer Code Signature Authorized Chrysler Dealer...
Page 426: If You Need Consumer Assistance
If You Need Assistance ....427 Reporting Safety Defects ....430 Chrysler Group LLC Customer Center ..428 In The 50 United States And Washington, D.C.
Page 427 426 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....431 Traction Grades ..... 433 Department Of Transportation Uniform Tire Temperature Grades .
Page 428: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 427 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 429: Chrysler Group Llc Customer Center
• Vehicle delivery date and mileage This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004...
Page 430: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 429 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 431: Warranty Information
See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
Page 432: In Canada
Customer Service Department imme- need in diagnosing/troubleshooting, problem solving, diately. Canadian customers who wish to report a safety maintaining, servicing, and repairing Chrysler Group defect to the Canadian government should write to: LLC vehicles. A complete working knowledge of the...
Page 433 • Diagnostic Procedure Manuals acquaint you with specific Chrysler Group LLC ve- hicles. Included are starting, operating, emergency Diagnostic Procedure Manuals are filled with dia- and maintenance procedures as well as specifications, grams, charts and detailed illustrations.
Page 434 IF YOU NEED CONSUMER ASSISTANCE 433 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 435 434 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 436 INDEX...
Page 437 436 INDEX About Your Brakes ..... . . 264 Airbag Maintenance ..... . . 63 ABS (Anti-Lock Brake System) .
Page 438 INDEX 437 Automatic Oil Change Indicator ..164,174,408 Body Mechanism Lubrication ....364 Automatic Temperature Control (ATC) ..235 B-Pillar Location .
Page 439 438 INDEX Caps, Filler Child Restraint Tether Anchors ... . . 70,72 Fuel ....... 314 Cigar Lighter .
Page 440 INDEX 439 Coolant Pressure Cap (Radiator Cap) ..371 Daytime Running Lights ....127 Cooling System .
Page 441 440 INDEX Door Opener, Garage ..... 138 Towing ......344 Driver’s Seat Back Tilt .
Page 442 INDEX 441 Oil Filter Disposal ..... 359 Air Conditioning ....241,363 Oil Selection .
Page 443 442 INDEX Fluid Capacities ......403 Filler Door (Gas Cap) ....158 Fluid Leaks .
Page 444 INDEX 443 Gauges Head Restraints ......118 Coolant Temperature ....158 Headlights .
Page 445 444 INDEX Hitches Integrated Power Module (Fuses) ... . 388 Trailer Towing ......319 Interior Appearance Care .
Page 446 INDEX 445 Lane Change and Turn Signals ... 128,166 Center Mounted Stop ....402 Lane Change Assist .
Page 447 446 INDEX Lights On Reminder ....124 Tires ....... 282 Low Fuel .
Page 448 INDEX 447 Master Cylinder (Brakes) ....374 Occupant Restraints ....37,58,61 Memory Feature (Memory Seat) .
Page 449 448 INDEX Viscosity ......358,403 Phone, Cellular ......112 Oil Filter, Change .
Page 450 INDEX 449 Radial Ply Tires ......289 Remote Starting System ....27 Radiator Cap (Coolant Pressure Cap) .
Page 451 450 INDEX Safety Tips ......78 Heated ......114 Satellite Radio Antenna .
Page 452 INDEX 451 Shifting Starting Procedures ..... . 247 Automatic Transaxle ....250 Steering Shoulder Belts .
Page 453 452 INDEX Temperature Gauge, Engine Coolant ..158,330 Inflation Pressures ..... 287 Tether Anchor, Child Restraint ....70 Jacking .
Page 454 INDEX 453 Towing ....... 318 Operation ......250 Disabled Vehicle .
Page 455 454 INDEX Uconnect™ (Hands-Free Phone) ... . . 112 Warning Lights Understanding Your Instrument Panel ..156 (Instrument Cluster Description) ... . . 158 Uniform Tire Quality Grades .
Page 456 INDEX 455 Windshield Wiper Blades ....365 Wiper Blade Replacement ....365 Windshield Wipers .
Page 457 Chrysler Group LLC 10C27-126-AC Printed in U.S.A. 3rd Edition...

Chrysler Sebring Convertible 2010 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

Chapters

Related Manuals for Chrysler Sebring Convertible 2010

Summary of Contents for Chrysler Sebring Convertible 2010