Page 1: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 3: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL This manual has been prepared with the assistance of Consult the table of contents to determine which section service and engineering specialists to acquaint you with contains the information you desire. the operation and maintenance of your new vehicle. It is The detailed index at the back of this manual contains a supplemented by a Warranty Information Booklet and complete listing of all subjects.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 To Arm The System .....19 Ignition Key Removal .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm ....25 Trunk Safety Warning .....38 Programming Additional Transmitters .
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Child Restraint ......62 Exhaust Gas ......74 Engine Break-In Recommendations .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key You can insert the double-sided keys into the locks with code numbers for your vehicle locks. These numbers can either side up.
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inop- erable. The engine can be started and stopped, but the key cannot be removed until you obtain service. •...
Page 14: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE details, refer to “Key-Off Power Delay,” under “Per- CAUTION! sonal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” An unlocked car is an invitation to thieves. Always in Section 4 of this manual. remove key from the ignition and lock all doors when leaving the vehicle unattended.
Page 15: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 turn for three seconds for a bulb check. If the light SENTRY KEY The Sentry Key Immobilizer System prevents unautho- remains after the bulb check, it indicates that there is a rized vehicle operation by disabling the engine. The problem with the electronics.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Replacement Keys • The Sentry Key Immobilizer System is not compat- NOTE: Only keys that have been programmed to the ible with some aftermarket remote starting systems. vehicle electronics can be used to start the vehicle. Once Use of these systems may result in vehicle starting a Sentry Key has been programmed to a vehicle, it problems and loss of security protection.
Page 17: Sentry Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 4. Insert a blank Sentry Key into the ignition switch. Sentry Key Programming You can program new keys to the system if you have two Turn the ignition switch to the position within 60 sec- valid sentry keys by performing the following procedure: onds.
Page 18: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle. The remaining keys must then be repro- SECURITY ALARM SYSTEM — IF EQUIPPED grammed. All vehicle keys must be taken to the dealer at The Vehicle Security Alarm (VSA) system monitors the the time of service to be reprogrammed.
Page 19: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 • Once armed, the system disables the unlock switch on To Arm the System: the driver door trim panel and passenger door trim 1. Remove the keys from the ignition switch and exit the panel, the trunk release button on the instrument vehicle.
Page 20: Illuminated Entry System - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the system is armed, the interior power door Tamper Alert lock switches will not unlock the doors. If something has triggered the alarm in your absence, and the warning signals have timed out, the park and tail- The VSA system is designed to protect your vehicle;...
Page 21: Remote Keyless Entry
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 The interior lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned on. NOTE: • The illuminated entry system will not operate the interior lights if the dimmer control is in the “defeat”...
Page 22 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Key Unlock, Driver Door/All Doors First 2. Release both buttons at the same time. This feature lets you program the system to unlock either 3. Test the feature while outside of the vehicle, by the driver’s door or both doors on the first press of the pressing the LOCK/UNLOCK buttons on the transmitter UNLOCK button on the transmitter.
Page 23 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles equipped with the Electronic Vehicle 4. Repeat these steps if you want to return this feature to Information Center (EVIC), refer to “Flash Lights with its previous setting. Lock,” under Personal Settings (Customer Program- NOTE: Pressing the LOCK button on the transmitter mable Features)”...
Page 24: To Lock The Doors
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors: 1. Press the LOCK button on a programmed transmitter Press and release the LOCK button on the transmitter to for at least 4 seconds, but not longer than 10 seconds. lock both doors.
Page 25: Convertible Top Operation
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Convertible Top Operation Using The Panic Alarm: Refer to “Convertible Top Operation” under “Under- To turn the panic alarm feature ON or OFF, press and standing The Features Of Your Vehicle” in Section 2 of hold the PANIC button on the transmitter for at least one this manual.
Page 26: Programming Additional Transmitters
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters Refer to SENTRY KEY “Customer Key Programming.” If you do not have a programmed transmitter, contact your dealer for details. Battery Replacement The recommended replacement battery is CR2032. NOTE: •...
Page 27: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 General Information REMOTE STARTING SYSTEM — IF EQUIPPED This device complies with part 15 of FCC rules and with This system uses the Remote Keyless Entry (RKE) trans- RS-210 of Industry Canada. Operation is subject to the mitter to start the engine conveniently from outside the following conditions: vehicle while still maintaining security.
Page 28: To Enter Remote Start Mode
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The vehicle must be equipped with an auto- To Enter Remote Start Mode matic transaxle to be equipped with Remote Start. Press and release the Remote Start button on the RKE transmitter twice. The engine will start How To Use Remote Start and the vehicle will remain in the Remote Start All of the following conditions must be met before the...
Page 29: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Exit Remote Start Mode & Drive the Vehicle NOTE: To avoid inadvertent shut downs, the system Before the end of the 15 minute cycle, press and release will disable the one-time press of the remote start button the UNLOCK button on the RKE transmitter to unlock for two seconds after receiving a valid remote start the doors and disarm the Vehicle Security Alarm (if...
Page 30: Power Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks WARNING! A door lock switch is located on the driver and passenger door trim panel. Press this switch to lock or unlock the • For personal security and safety in the event of an doors.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Automatic Door Locks Automatic Unlock Doors on Exit Programming The Auto Door Locks feature can be enabled or disabled The Auto Unlock on Exit feature can be enabled or by your authorized dealer. See your dealer for program- disabled as follows: ming.
Page 32: Windows
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will indicate the completion of the programming. 5. Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Auto Unlock on Exit feature in accor- dance with local laws.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 There is a single window control on the passenger’s door WARNING! trim panel, which operates the passenger door window. The window controls will operate when the ignition Never leave children in a vehicle, with the keys in switch is turned to the ON or ACC position, and when the ignition switch.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, push the window switch either door will cancel this feature. The time for this to the first detent and release it when you want the feature is programmable. For details, refer to “Key-Off window to stop.
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: ANTI-PINCH PROTECTION Reset Auto Up If the vehicle battery goes dead, the auto feature will be • If the window runs into any obstacle during auto- disabled. To reactivate the auto feature, perform the closure, it will reverse direction and then stop.
Page 36: Wind Buffeting
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE passenger door, press and release the window lock Wind Buffeting button (setting it in the down position). To enable the Wind buffeting can be described as the perception of window control, press and release the window lock pressure on the ears or a helicopter type sound in the button again (setting it in the up position).
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 NOTE: The following conditions must be met in order To unlatch the trunk lid from outside the vehicle, press for this switch to operate: and release the TRUNK button on the Remote Keyless Entry (RKE) transmitter two times.
Page 38: Trunk Safety Warning
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK SAFETY WARNING Trunk Emergency Release WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended.
Page 39: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • An energy absorbing steering column and steering inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the wheel. trunk latching mechanism. See picture. •...
Page 40: Lap/Shoulder Belts
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The front airbags have a dual-stage inflator and cause a collision that includes you. This can happen design. This allows the airbag to have different rates of far away from home or on your own street. inflation that are based on collision severity.
Page 41: Lap/Shoulder Belt Operating
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Lap/Shoulder Belt Operating Instructions WARNING! 1. Enter the vehicle and close the door. Sit back and • Be sure everyone in your vehicle is in a seat and using a adjust the front seat. seat belt properly.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt that is buckled into the wrong buckle will not protect you properly.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, •...
Page 44: Lap/Shoulder Belt Untwisting Procedure
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Lap/Shoulder Belt Untwisting Procedure The belt will automatically retract to its stowed position. Use the following procedure to untwist a twisted lap/ If necessary, slide the latch plate down the webbing to shoulder belt.
Page 45: Seat Belt Pretensioners
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 are single use items. After a collision that is severe Seat Belt Pretensioners The seat belts for both front seating positions are enough to deploy the airbags and pretensioners, both equipped with pretensioning devices that are designed to must be replaced.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert Programming 3. Within 60 seconds of turning the ignition switch to the The Enhanced Warning System (BeltAlert ) can be en- ON position, unbuckle and then re-buckle the driver’s abled or disabled by your authorized dealer or by seat belt at least three times within 10 seconds, ending performing the following steps: with the seat belt buckled.
Page 47: Automatic Locking Mode
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 How To Disengage The Automatic Locking Mode Automatic Locking Mode In this mode, the shoulder belt is automatically pre- Unbuckle the combination lap/shoulder belt and allow it locked. However, the belt will still retract to remove any to retract completely to disengage the Automatic Locking slack in the shoulder belt.
Page 48: Seat Belt Extender
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender Driver and Front Passenger Supplemental If a seat belt is too short, even when fully extended, your Restraint System (SRS) - Airbag dealer can provide you with a seat belt extender. This This vehicle has airbags for both the driver and front extender should be used only if the existing belt is not passenger as a supplement to the seat belt restraint...
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! • Do not put anything on or around the front airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, front airbags Infants in rear facing child restraints should NEVER ride work with the knee bolsters to provide improved protec- in the front seat of a vehicle with a passenger front airbag. tion for the driver and front passenger.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 You should read the instructions provided with your WARNING! child restraint to make sure that you are using it properly. • Relying on the airbags alone could lead to more 2. All occupants should wear their lap and shoulder severe injuries in a collision.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Knee Impact Bolsters Airbag System Components The airbag system consists of the following: • Driver and Front Passenger Seat Belt Pretensioners • Occupant Restraint Controller (ORC) How the Airbag System Works •...
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • Driver Airbag Special Features The ORC determines if a frontal collision is severe Driver airbag deployment and force level is controlled by enough to require the airbags to inflate. Based on the the driver’s seat position as well as impact severity.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Impact Sensors The ORC also turns on the AIRBAG warning light in the instrument panel for six to eight Two sensors, located on the front body structure, trigger seconds for a self-check when the ignition is first airbag deployment in direct frontal impacts and aid the turned on.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 When the bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each bag deploys independently, that is a left side impact deploys the left bag only and a right-side impact deploys only the right bag.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not add a secondary seat cover other than those If A Deployment Occurs approved by DaimlerChrysler/Mopar. The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detects a moderate- •...
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • It is not advisable to drive your vehicle after the However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor airbags have deployed. If you are involved in another immediately.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System Maintaining Your Airbag System In the event of an impact that causes airbag deployment, WARNING! with the vehicle stopped, and the vehicle communication network intact, and the power intact, the Enhanced •...
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Airbag Warning Light WARNING! You will want to have the airbags ready to inflate for your protection in a collision. While Do not attempt to modify any part of your advanced the airbag system is designed to be mainte- airbag system.
Page 60: Event Data Recorder (Edr)
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE fuses. Refer to “Fuses” in this manual for fuse location In conjunction with other data gathered during a com- information. See your authorized dealer for service. plete accident investigation, the electronic data may be used by DaimlerChrysler Corporation and others to learn Event Data Recorder (EDR) more about the possible causes of crashes and associated...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 provided to the custodial entity upon request. General Data Parameters that May Be Recorded: data that does not identify particular vehicles or crashes • Diagnostic trouble code(s) and warning light status for may be released for incorporation in aggregate crash electronically-controlled safety systems, including the databases, such as those maintained by the US govern-...
Page 62: Child Restraint
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status. WARNING! • Traction/stability control status. In a collision, an unrestrained child, even a tiny baby, • Tire pressure monitoring system status – If Equipped. can become a missile inside the vehicle. The force required to hold even an infant on your lap could Child Restraint become so great that you could not hold the child, no...
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Infants and Child Restraints “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section. • Safety experts recommend that children ride • Rearward-facing child seats must NEVER be used in rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Make sure that the child is upright in the seat. The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit •...
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Here are some tips on getting the most out of your child WARNING! restraint: • Improper installation can lead to failure of an • Children who are large enough to wear the shoulder infant or child restraint.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All passenger seating positions contain automatic LATCH-compatible child seats having flexible, webbing- locking retractors. However, any seat belt system will mounted lower attachments or fixed lower attachments. loosen with time, so check the belt occasionally and Regardless of the specific type of lower attachment, pull it tight if necessary.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 provide add-on tether strap kits for some of their older restraint systems having attachments for those anchor- products. Tether anchorage kits are also available for ages will continue to have features for installation in most older vehicles.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remind all children in the vehicle that the seat belts are In addition, there are tether strap anchorages not toys and should not be played with, and never leave behind each rear seating position. Access ports your child unattended in the vehicle.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 seat cover material. Then rotate the tether anchorage stow the seat belt out of the reach of an inquisitive child. cover directly behind the seat where you are placing the Remind all children in the vehicle that the seat belts are child restraint and attach the tether strap to the anchor- not toys and should not be played with, and never leave age, being careful to route the tether strap to provide the...
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belt must be in the Automatic Locking Mode in buckle and twist the short buckle-end belt several times order to enable a child restraint to be tightly installed. to shorten it. Insert the latch plate into the buckle with the Refer to “Automatic Locking Mode”...
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 4. Open the access cover (C) on the carpet covering the back of the seat and attach the tether strap hook (D) to the anchor. Child Tether Access Port Cover 3. Push the tether strap and hook (B) through the access port and down into the trunk.
Page 72: Engine Break-In Recommendations
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine in your new vehicle. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 73: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 The recommended viscosity and quality grades are WARNING! shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE It is extremely dangerous to ride in a cargo area, USED.
Page 74: Exhaust Gas
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas seams or loose connections could permit exhaust fumes Do not run the engine in a closed garage or in confined to seep into the passenger compartment. In addition, areas any longer than needed to move your vehicle in or inspect the exhaust system each time the vehicle is raised out of the area.
Page 75: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Defroster Safety Checks You Should Make Inside The Vehicle Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Seat Belts feel the air directed against the windshield. See your Inspect the belt system periodically, checking for cuts, authorized dealer for service if your defroster is inoper- frays, and loose parts.
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Fluid Leaks Have someone observe the operation of exterior lights Check area under vehicle after overnight parking for fuel, while you work the controls. Check turn signal and high engine coolant, oil, or other fluid leaks. Also, if gasoline beam indicator lights on the instrument panel.
Page 77: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....81 Mirrors .......96 Power Convertible Top Usage Precautions .
Page 78 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features ....108 Power Seats — If Equipped ....134 UConnect System Features .
Page 79 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Fog Lights — If Equipped ....141 Electronic Speed Control — If Equipped ..151 Turn Signals .
Page 80 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security ......160 Cup Holders ......164 Troubleshooting Tips .
Page 81: Convertible Top Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 takes approximately 30 seconds. The entire process, in- CONVERTIBLE TOP OPERATION cluding unlatching or latching the top at the windshield WARNING! header is automatic. The top does take up some space in the trunk when The convertible top does not provide the structural retracted.
Page 82: Power Convertible Top Usage Precautions
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Power Top Control Module (PTCM) monitors and When raising the top, the system retracts the hard tonneau cover back into its stowage area underneath the controls lowering and raising of the top. A series of trunk lid.
Page 83 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 CAUTION! CAUTION! Before operating the Power Top: • Correctly position the cargo protector in the trunk 1. Always check the tonneau cover area to be sure that it is before stowing the top. Doing so closes a switch clear of debris or other items.
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • Do not operate the Power Top when the vehicle is in motion. • Before operating the Power Top, make sure that no moving parts of the convertible top can injure a person or animal. •...
Page 85: Cargo Protector
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Cargo Protector The cargo protector is located in the trunk. Before low- ering the convertible top, you must unfold the cargo protector and seat the tabs at each end of the cargo protector in the V slots in the trunk liner. Doing so closes a switch that allows top operation.
Page 86: Power Convertible Top Controls
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Convertible Top Controls There is also a Power Top button on the Remote Keyless The Power Top switch is located on the instrument panel Entry (RKE) Transmitter for remotely lowering the power to the left of the steering column.
Page 87: Lowering The Power Convertible Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Using the Remote Keyless Entry (RKE) Transmitter Lowering the Power Convertible Top Using the Power Top Switch 1. Press and release the Unlock button. 2. Press, release, then press, and hold the NOTE: The Power Top switch will operate when the Power Top button down until the operation of ignition switch is turned to the ON or ACC position and lowering the top and all four windows to their...
Page 88: Wind Stop
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the switch in the Top Up 1. Read all of the Notes, Cautions, and Warning found position until the operation of raising the top under “Power Convertible Top Usage Precautions” to and latching it is complete, which is indicated verify all operating conditions are met.
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 NOTE: It is recommended that you lower the convert- ible top before installing or removing the Wind Stop. Installing the Wind Stop 1. Remove the Wind Stop from the trunk. 2. Unfold the Wind Stop framework. 3.
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Pivot the small frame (1) away from the large frame (2) 5. Unfold both stems at the rear of the large frame. until the pivot lock (3) engages to lock the two frames in an L shape.
Page 91 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 6. Align and insert the stems into the slot in each trim 7. Align the pins at the front of the large frame with the panel. hole in each trim panel. Slide the pins outward until fully extended into each hole.
Page 92: Power Convertible Top Operation & Warning Messages
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing & Storing the Wind Stop Power Convertible Top Operation & Warning Reverse the installation procedure to remove, fold, and Messages store the Wind Stop. However, note the following before When the appropriate conditions exist, the PTCM dis- doing so: plays various power convertible top operation and warn- ing messages in the Electronic Vehicle Information Center...
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 EVIC EVIC Odometer Odometer Odometer Odometer Operator Chime Condition Message Message Message Message Message Action Message Display (< 5 mph Display (> 5 mph Display Required Time [8 km/h]) Time [8 km/h]) Time CONVERT- Until Op- Until Opera-...
Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC EVIC Odometer Odometer Odometer Odometer Operator Chime Condition Message Message Message Message Message Action Message Display (< 5 mph Display (> 5 mph Display Required Time [8 km/h]) Time [8 km/h]) Time SPEED TOO 9 Seconds SPEED TOO...
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 If so equipped. For vehicles not equipped with the EVIC. The PTCM will LOCKOUT the power convertible top system if the vehicle charging system is malfunc- tioning, or the battery is run down, or the hydraulic pump is overheating. In addition, the system prohibits low- ering the top when ambient temperature is at 0°F (-18°C) or lower and raising the top when ambient temperature is below -40°F (-40°C).
Page 96: Mirrors
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light will illuminate to indicate when the dimming feature is activated.
Page 97: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 CAUTION! WARNING! To avoid damage to the mirror during cleaning, never Vehicles and other objects seen in the passenger side spray any cleaning solution directly onto the mirror. convex mirror will look smaller and farther away Apply the solution onto a clean cloth and wipe the than they really are.
Page 98: Power Remote Control Mirrors
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote Control Mirrors After selecting a mirror, move the knob in the same The power mirror switch is located on the driver’s door direction you want the mirror to move. When finished, trim.
Page 99: Heated Remote Control Mirrors - If Equipped
IF EQUIPPED following websites: NOTE: The sales code RER radio contains an inte- • www.chrysler.com/uconnect grated Hands-Free Communication (UConnect ) sys- tem. Refer to your “Navigation User’s Manual” for • www.dodge.com/uconnect UConnect system operating instructions for this radio.
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect allows you to transfer calls between the Phone Button system and your cellular phone as you enter or exit your The rearview mirror contains the microphone vehicle and enables you to mute the system’s microphone for the system (depending on the type of for private conversation.
Page 101: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • For certain operations, compound commands can be The UConnect system is fully integrated with the vehi- cle’s audio system. The volume of the UConnect system used. For example, instead of saying Setup and then can be adjusted either from the radio volume control Phone Pairing, the following compound command knob or from the steering wheel radio control (right...
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help Command To complete the pairing process, you will need to refer- If you need assistance at any prompt, or if you want to ence your cellular phone owner’s manual. The know your options at any prompt, say Help following UConnect website may also provide detailed instruc- the beep.
Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • For identification purposes, you will be prompted to Dial by Saying a Number give the UConnect system a name for your cellular • Press the PHONE button to begin. phone. Each cellular phone that is paired should be •...
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call by Saying a Name Add Names to Your UConnect Phonebook • Press the PHONE button to begin. NOTE: Adding names to the phonebook is recom- mended when the vehicle is not in motion. •...
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 After you are finished adding an entry into the phone- NOTE: • Phone handset must support Bluetooth OBEX trans- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the fers of phonebook entries to use this feature.
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit Entries in the UConnect Phonebook Phonebook Edit can be used to add another phone number to a name entry that already exists in the NOTE: Editing names in the phonebook is recom- phonebook.
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • After confirmation, the phonebook entries will be from which you choose. To select one of the entries from the list, press the VOICE RECOGNITION button deleted. while the UConnect system is playing the desired •...
Page 108: Phone Call Features
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect system will then prompt you as to the the call, press and hold the PHONE button until you hear number designation you wish to call. a single beep, indicating that the incoming call was rejected.
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 or Call followed by the phone number or phonebook Conference Call entry you wish to call. The first call will be on hold while When two calls are in progress (one active and one on the second call is in progress.
Page 110: Uconnect System Features
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched OFF, a call can hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press continue on the UConnect system either until the call and hold the PHONE button until you hear a single beep.
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • After the Ready prompt and the following beep, say If the phone is not reachable and the UConnect system the name of the language you wish to switch to is operational, you may reach the emergency number as (English, Espanol, or Francais, if so equipped).
Page 112 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the Paging UConnect system to allow use of this vehicle feature in To learn how to page, refer to Working with Automated emergency situations, when the cell phone has network Systems.
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 When calling a number with your UConnect system entry you wish to send. The UConnect system will then that normally requires you to enter in a touch-tone send the corresponding phone number associated with sequence on your cellular phone keypad, you can press the phonebook entry, as tones over the phone.
Page 114 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Dialing Using the Cellular Phone Keypad Turning confirmation prompts off will stop the system You can dial a phone number with your cellular phone from confirming your choices (e.g., the UConnect sys- keypad and still use the UConnect system (while dial- tem will not repeat a phone number before you dial it).
Page 115: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Mute/Un-Mute (Mute Off) UConnect system or vice versa, press the VOICE REC- When you mute the UConnect system, you will still be OGNITION button and say Transfer Call. able to hear the conversation coming from the other Connect or Disconnect Link Between the party, but the other party will not be able to hear you.
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect system will play the phone names of • The selected phone will be used for the next phone all paired cellular phones in order from the highest to call. If the selected phone is not available, the the lowest priority.
Page 117: Things You Should Know About Your Uconnect System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Repeat the words and phrases when prompted by the Things You Should Know About Your UConnect System UConnect system. For best results, the Voice Training session should be completed when the vehicle is parked UConnect Tutorial with the engine running, all windows closed, and the To hear a brief tutorial of the system features, press the...
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Speak normally, without pausing, just as you would • When navigating through an automated system such speak to a person sitting a few feet/meters away from as voice mail, or when sending a page, at the end of you.
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • In a convertible vehicle, system performance may be • Echo at the far end can sometimes be reduced by compromised with the convertible top down. lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be Far End Audio Performance compromised with the convertible top down.
Page 120 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121...
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 124 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 125: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 possible. The ability of the Voice Interface System to General Information This device complies with part 15 of the FCC rules and recognize user voice commands may be negatively af- RSS 210 of Industry Canada. Operation is subject to the fected by rapid speaking or a raised voice level.
Page 126: Commands
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the VR hard-key, listen for the beep, and dows are closed, and the heater/air-conditioning fan is say your command.
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 • NEXT STATION (to select the next station) 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition • PREVIOUS STATION (to select the previous station) system is speaking.
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Satellite Radio Disc To switch to satellite radio mode say SAT or SATELLITE To switch to the disc mode say DISC. In this mode, you RADIO. In this mode, you may say the following com- may say the following commands: mands: •...
Page 129: Voice Training
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 − CONTINUE (to continue recording) Voice Training For users experiencing difficulty with the system recog- − DELETE (to delete the recording) nizing their voice commands or numbers, the UConnect • PLAY MEMOS (to play previously recorded memos) system Voice Training feature may be used.
Page 130: Seats
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Forward & Rearward Adjustment — If Equipped The manual seat adjustment bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward.
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Page 132 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE inboard side of the seat. Turn the control lever downward WARNING! to increase and upward to decrease the desired amount of lumbar support. • Adjusting a seat while the vehicle is moving is dangerous.
Page 133: Easy Entry System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 On the passenger seat, pull the lever upward to move the Easy Entry System The Easy Entry lever is located on upper seat belt anchor seat and seatback forward. cover. When returning the seat to its normal position, the memory feature restores the seat position and seatback recline position to their current settings.
Page 134: Power Seats - If Equipped
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped CAUTION! The power seat switch is on the outboard side of the seat Do not place any article under any seat as it may near the floor. Use the switch to move the seat up, down, cause damage to the seat controls.
Page 135: Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Head Restraints Heated Seats — If Equipped Head restraints can reduce the risk of whiplash injury in Heated seats provide comfort and warmth on cold days the event of impact from the rear. Adjust the restraint so and can help soothe sore muscles and backs.
Page 136 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 137: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Next, move to the outside of the vehicle and lift the TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. First, pull secondary latch underneath the center front edge of the the hood release lever located under the left side of the hood.
Page 138: Lights
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod to secure the hood in the open slam the hood to close it. Use a firm downward push at position. Place the upper end of the prop rod in the hole the center of the hood to ensure that both latches engage.
Page 139: Headlights & Parking Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Headlights & Parking Lights Automatic Headlights — If Equipped Turn the end of the Multi-Function Control Lever to the This system automatically turns the headlights ON or first detent for parking light operation. Turn the end of OFF according to ambient light levels.
Page 140: Headlight Time Delay - If Equipped
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE AUTO position. In addition, the headlights will turn OFF interval begins when you turn off the headlights. Only when the wipers are turned off if they were turned on by the headlights will illuminate during this time. this feature.
Page 141: Lights-On Reminder
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 the headlight switch is off, the parking brake is off, the turn signal is off, and the selector lever is in any position except “P” (Park). The Daytime Running Lights will turn off NOTE: automatically when the turn signal is in operation and turn on again when the turn signal is not operating.
Page 142: Turn Signals
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals You can signal a lane change by moving the lever Move the Multi-Function Lever upward or downward partially upward or downward without moving beyond and the corresponding turn signal indicator on the in- the detent.
Page 143: Flash To Pass
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Flash to Pass You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. NOTE: If the Multi-Function Control Lever is held in the Flash to Pass position for more than 15 seconds, the high beams will shut off.
Page 144: Interior Lights
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights A courtesy light is also found in the rear of the center Two courtesy/reading lights are located in the bottom of console. You can turn this light on and off from the the rearview mirror.
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Parade Mode (Daytime Brightness Feature) Rotate the Dimmer Control to the first detent to brighten the odometer and radio display when the parking lights or headlights are on during daylight conditions. Interior Light ON Rotate the Dimmer Control completely upward to the second detent to turn on the interior lights.
Page 146: Windshield Wipers And Washers
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Rotate the end of the lever to the first detent past the The Windshield Wiper / Washer Control Lever is intermittent settings for Low-speed wiper operation, or located on the right side of the steering column. to the second detent past the intermittent settings for High-speed wiper operation.
Page 147: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Intermittent Wiper System CAUTION! Use the intermittent wiper system when weather condi- tions make a single wiping cycle with a variable pause • Turn the windshield wipers off when driving between cycles desirable. Rotate the end of the Wind- through an automatic car wash.
Page 148: Mist Feature
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
Page 149: Windshield Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 addition, the headlights will turn OFF when the wipers If you activate the washer while the wiper control is in are turned off if they were turned on by this feature. the OFF position, the wipers will operate for two wipe cycles and then turn OFF.
Page 150: Tilt/Telescoping Steering Column
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward.
Page 151: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WARNING! Do not adjust the steering wheel while driving. The tilt/telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt/telescoping adjustment locked could cause the driver to lose control of the vehicle.
Page 152: To Set At A Desired Speed
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE release the ONOFF button a second time. The CRUISE To Set At A Desired Speed: indicator will turn off. Be sure to turn the system OFF When the vehicle reaches the speed desired, press down when not in use.
Page 153: To Resume Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 To decrease speed while the speed control is set, push To Resume Speed: If you deactivated the speed control without erasing the down and hold the lever SET DECEL. Release the lever set speed from memory and your vehicle speed is above when the desired speed is reached, and the new set speed 20 mph (32 km/h) you can resume the previous set will be established.
Page 154: To Accelerate For Passing
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing: WARNING! Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Speed Control can be dangerous where the system can’t maintain a constant speed.
Page 155: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink unit operates off your vehicle’s battery.
Page 156: Programming Homelink
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! Your motorized door or gate will open and close Vehicle exhaust contains carbon monoxide, a danger- while you are training the Universal Transceiver. Do ous gas. Do not run your vehicle in the garage while not train the transceiver if people or pets are in the training the transceiver.
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 It is recommended that a new battery be placed in the Watch for the HomeLink indicator to change flash rates. hand-held transmitter of the device being programmed When it changes, it is programmed. It may take up to 30 to HomeLink for more efficient training and accurate seconds, or longer in rare cases.
Page 158 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Press and hold the just-trained HomeLink button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink button is pressed. If the indicator light blinks rapidly for two seconds, and then turns to a constant light, continue with program- ming for Rolling Code.
Page 159: Gate Operator/Canadian Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 7. Return to the vehicle and press the programmed Similar to this Canadian law, some U.S. gate operators are HomeLink button twice (holding the button for 2 sec- designed to “time-out” in the same manner. onds each time).
Page 160: Using Homelink
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then proceed with Step 4 under “Programming 3. Without releasing the button, proceed with PRO- HomeLink .” earlier in this section. GRAMMING HOMELINK Step #2 and follow all re- maining steps. Using HomeLink To operate, simply press and release the programmed Security HomeLink button.
Page 161: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 • Press the Learn Button on the Garage Door Opener to NOTE: The transmitter has been tested and it complies complete the training for Rolling Code. with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- •...
Page 162 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If desired, the instrument panel power outlet The center console power outlet is powered directly from can be converted by your authorized dealer to provide the battery (power available at all times). Items plugged power with the ignition switch while in the “LOCK”...
Page 163: Electrical Outlet Use With Engine Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Electrical Outlet Use With Engine Off CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED Cup Holder Ash Receiver — If Equipped CAUTION! An optional ash receiver is available from your autho- • Many accessories that can be plugged in draw rized dealer and will fit in either one of the center console cup holders.
Page 164: Cup Holders
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS CAUTION! Front Seat Cup Holder For vehicles equipped with the heated and cooled The cup holder in the center console will accommodate cup holder, locate the cup holder ash receiver in the either two large size cups or two 20 oz.
Page 165: Rear Seat Cup Holders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 unit is on and the LED is Red, the cup holder is being Rear Seat Cup Holders heated. When the LED is Blue, the cup holder is being Cup holders for the rear seat occupants are located in the cooled.
Page 166: Console Features
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Storage The center console contains a cubby bin with flip-down cover located below the climate controls. This compart- ment also contains a 12-volt electrical outlet. WARNING! Do not place ashes inside the cubby bin located on the center console.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also con- tains a 12-volt power outlet and a molded-in coin holder (designed to hold various size coins).
Page 168: Sliding Armrest - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sliding Armrest — If Equipped On some models, the center console armrest slides for- ward and rearward for added user comfort.
Page 169: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....173 Compass Display ..... 191 Base Instrument Cluster .
Page 170 170 UNDERSTANDING YOUR INSTRUMENT PANEL FM Reception ......197 Operating Instructions — Voice Recognition System (VR) (If Equipped) ....214 Sales Code REQ —...
Page 171 UNDERSTANDING YOUR INSTRUMENT PANEL 171 Play Mode ......222 Operating Instructions - Video Entertainment System (VES™) (If Equipped) ... . . 229 List Or Browse Mode .
Page 172 172 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control (ATC) — Rear Window Features ....246 If Equipped ......237 Electric Rear Window Defroster —...
Page 173: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 173 INSTRUMENT PANEL FEATURES 1 — Air Outlet 6 — Radio 11 — Hazard Switch 2 — Side Window Demister Outlet 7 — Passenger Airbag 12 — Storage Compartment 3 — Instrument Cluster 8 — Glove Box 13 —...
Page 174: Base Instrument Cluster
174 UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER...
Page 175: Premium Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 175 PREMIUM INSTRUMENT CLUSTER...
Page 176: Instrument Cluster Descriptions
176 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle. 1. Fuel Gauge Idle the vehicle with the air conditioner turned off until When the ignition switch is in the ON position, the the pointer drops back into the normal range.
Page 177 UNDERSTANDING YOUR INSTRUMENT PANEL 177 5. Low Fuel Light come on during starting, stays on, or comes on while When the fuel level drops to 2 gallons, the fuel driving, have the system checked by an authorized symbol will light and a single chime will sound. dealer.
Page 178 178 UNDERSTANDING YOUR INSTRUMENT PANEL will turn off after the engine is started. If the bulb does 12. Tachometer not come on during starting, have the system checked by The white area of the scale shows the permissible engine an authorized dealer. revolutions-per-minute (rpm x 1000) for each gear range.
Page 179 UNDERSTANDING YOUR INSTRUMENT PANEL 179 The two trip odometers show individual trip mileage. To gASCAP switch from odometer to trip odometers, press and If the vehicle diagnostic system detects a leak or change release the Trip Odometer button. To reset a trip odom- in the evaporative system, or the fuel filler cap is loose, eter, display the desired trip odometer to be reset then improperly installed, or damaged, the words “gASCAP”...
Page 180 180 UNDERSTANDING YOUR INSTRUMENT PANEL indicator system is duty cycle based, which means the NOTE: If the indicator message illuminates when you engine oil change interval may fluctuate dependent upon start the vehicle, the oil change indicator system did not your personal driving style.
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 181 Dual Trip Odometer — If Equipped If the light is flashing when the engine is running you may experience power loss, an elevated/rough idle, and Press and release this button to change the display from increased brake pedal effort, and your vehicle may odometer to “Trip A.”...
Page 182 182 UNDERSTANDING YOUR INSTRUMENT PANEL 19. Brake System Warning Light If brake failure is indicated, immediate repair is neces- This light monitors various brake functions, sary. including brake fluid level and parking brake WARNING! application. If the brake light turns on, it may indicate that the parking brake is applied, that Driving a vehicle with the brake light on is danger- the brake fluid level is low, or that there is a problem with...
Page 183 UNDERSTANDING YOUR INSTRUMENT PANEL 183 The operation of the Brake Warning Light can be checked 22. Electronic Stability Program (ESP) Indicator Light by turning the ignition switch from the OFF position to The yellow ESP/BAS malfunction indicator the ON position. The light should illuminate for approxi- light will turn on when the ignition switch is mately two seconds.
Page 184 184 UNDERSTANDING YOUR INSTRUMENT PANEL the conventional brake system will continue to operate by the vehicle manufacturer on the vehicle placard or tire normally provided that the BRAKE warning light is not inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should deter- If the ABS light is on, the brake system should be serviced...
Page 185 UNDERSTANDING YOUR INSTRUMENT PANEL 185 NOTE: Please note that the TPMS is not a substitute for TPMS malfunction telltale after replacing one or more proper tire maintenance, and it is the driver’s responsi- tires or wheels on your vehicle to ensure that the replace- bility to maintain correct tire pressure, even if under- ment or alternate tires and wheels allow the TPMS to inflation has not reached the level to trigger illumination...
Page 186 186 UNDERSTANDING YOUR INSTRUMENT PANEL (Refer to “Tire Inflation Pressures” under “Tires — Gen- If the Malfunction Indicator Light flashes when the eral Information” and to “Tire Pressure Monitor System engine is running, serious conditions may exist that (TPMS)” in Section 5 of this manual for more informa- could lead to immediate loss of power or severe catalytic tion).
Page 187: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 187 • System Status ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED • Vehicle information warning message displays • Personal Settings (customer programmable features) • Compass heading display (N, S, E, W, NE, NW, SE, • Outside temperature display (°F or °C) •...
Page 188: Electronic Vehicle Information Center (Evic) Displays
188 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by Press and release the RESET Button to accept a pressing the following buttons on the Instrument Panel selection. The RESET Button also resets various Switch Bank: Trip Functions.
Page 189: Oil Change Required
UNDERSTANDING YOUR INSTRUMENT PANEL 189 • RKE (Remote Keyless Entry) Battery Low (with a • Convertible Top Malfunction (with a single chime) single chime) • Oil Change Required (with a single chime) • Personal Settings Not Available – Vehicle Not in Park. Oil Change Required •...
Page 190: Trip Functions
190 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn the ignition switch to the ON position (Do not Press and release the STEP button to advance the display start the engine). through the Trip Functions. 2. Fully depress the accelerator pedal slowly three times The Trip Functions mode displays the following informa- within 10 seconds.
Page 191: Compass Display
UNDERSTANDING YOUR INSTRUMENT PANEL 191 NOTE: Significant changes in driving style or vehicle To Reset The Display loading will greatly affect the actual drivable distance of Reset will only occur if a resettable function is currently the vehicle, regardless of the DTE display value. displayed.
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC will flash the CAL indicator until the compass is 4. Press and release the RESET Button and the CAL calibrated. You may calibrate the compass by completing indicator will quit flashing. one or more 360° turns (in an area free from large metal 5.
Page 193 UNDERSTANDING YOUR INSTRUMENT PANEL 193 1. Turn the ignition switch to the ON position. Leave the selector lever in PARK. 2. Press and release the MENU button until “Personal Settings” displays in the EVIC. 3. Press and release the STEP button until “Compass Variance”...
Page 194: Personal Settings (Customer Programmable Features)
194 UNDERSTANDING YOUR INSTRUMENT PANEL Personal Settings (Customer Programmable Auto Unlock On Exit When ON is selected, all doors will unlock when the Features) Personal Settings allows the driver to set and recall vehicle is stopped and the transaxle is in the PARK or features when the automatic transaxle is in PARK.
Page 195 UNDERSTANDING YOUR INSTRUMENT PANEL 195 Sound Horn with LOCK when exiting the vehicle. To make your selection, press When ON is selected, a short horn sound will occur when and hold the RESET button until 0, 30, 60, or 90 appears. the remote keyless entry LOCK button is pressed.
Page 196: Setting The Analog Clock
196 UNDERSTANDING YOUR INSTRUMENT PANEL Key Off Power Delay Display Units in English or Metric When this feature is selected, the power window The EVIC and odometer can be changed between English switches, radio, hands–free system (if equipped), and and Metric units of measure. To make your selection, power outlets will remain active for up to 10 minutes press and release the RESET button until US or METRIC after the ignition switch is turned to the LOCK position.
Page 197: Radio General Information
UNDERSTANDING YOUR INSTRUMENT PANEL 197 RADIO GENERAL INFORMATION Electrical Disturbances Radio waves may pick up electrical disturbances during Radio Broadcast Signals transmission. They mainly affect the wave amplitude, Your new radio will provide excellent reception under and thus remain a part of the AM reception. They most operating conditions.
Page 198: Sales Code Req - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
198 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: SALES CODE REQ — AM/FM STEREO RADIO • For vehicles not equipped with the Electronic Vehicle AND 6–DISC CD/DVD CHANGER Information Center (EVIC), the radio and steering (MP3/WMA AUX JACK) wheel radio controls (if equipped) will remain active NOTE: The radio sales code is located on the lower right for 45 seconds after the ignition switch is turned to the side of your radio faceplate.
Page 199: Operating Instructions - Radio Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 199 will remain tuned to the new station until you make Operating Instructions - Radio Mode another selection. Holding either button will bypass NOTE: The ignition switch must be in the ON or ACC stations without stopping until you release it. position to operate the radio.
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button (UConnect Hands-Free Phone) — If 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes Equipped Press this button to operate the Hands-Free Phone will begin to blink.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 201 RW/FF Push the rotary TUNE/SCROLL control knob a third Pressing the RW (Rewind) or FF (Fast Forward) buttons time and TREBLE will display. Turn the TUNE/SCROLL causes the tuner to search for the next frequency in the control knob to the right or left to increase or decrease the direction of the arrows.
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL seconds will allow the program format type to be se- Program Type 16–Digit Character Display lected. Many radio stations do not currently broadcast Nostalgia Nostalga Music Type information. Oldies Oldies Toggle the MUSIC TYPE button to select the following Personality Persnlty format types:...
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 203 • DISC Play/Pause - You can toggle between By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency playing the DVD and pausing the DVD by station with the same selected Music Type name.
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: These selections can only be made while playing Menu Language — If Equipped a DVD. Selecting this item will allow the user to choose the • VES Power - Allows you to turn VES™ ON and OFF default startup DVD menu language (effective only if (if equipped).
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 205 Subtitle Language — If Equipped Aspect Ratio — If Equipped Selecting this item allows you to choose a default subtitle Selecting this item allows you to choose between wide language (effective only if the language is supported by screen, pan scan, and letter box.
Page 206: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
206 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button — To Set the Pushbutton Memory Every time a preset button is used, a corresponding When you are receiving a station that you wish to button number will display. commit to pushbutton memory, press the SET button. Buttons 1 - 6 The symbol SET 1 will now show in the display window.
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 207 Radio display will show LOADING DISC when the disc CAUTION! is loading and “READING DISC” when the radio is reading the disc. The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate CAUTION! “Disc Hot”...
Page 208: Notes On Playing Mp3/Wma Files
208 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the eject button for five seconds and all RW/FF (CD MODE) CDs will be ejected from the radio. Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or The disc can be ejected with the radio and ignition OFF.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 209 Supported Medium Formats (File Systems) Multisession disc formats are supported by the radio. The medium formats supported by the radio are ISO 9660 Multisession discs may contain combinations of normal Level 1 and Level 2 and includes the Joliet extension. CD audio tracks and computer files (including MP3/ When reading discs recorded using formats other than WMA files).
Page 210 210 UNDERSTANDING YOUR INSTRUMENT PANEL frequencies in the following table are supported. In ID3 Tag information for artist, song title, and album title addition, variable bit rates (VBR) are also supported. The are supported for ID3 version 1 tags. ID3 version 2 is not majority of MP3/WMA files use a 44.1 kHz sampling rate supported by the radios.
Page 211: List Button
UNDERSTANDING YOUR INSTRUMENT PANEL 211 • Number of files and folders - Loading times will INFO Button (DISC Mode for MP3/WMA Play) increase with more files and folders Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File To increase the speed of disc loading, it is recommended Name, and Folder Name (if available).
Page 212 212 UNDERSTANDING YOUR INSTRUMENT PANEL Pushing the AUX button will change the mode to auxil- RW/FF (Auxiliary Mode) iary device if the AUX jack is connected. No function. NOTE: The AUX device must be turned on and the SET Button (Auxiliary Mode) device’s volume set to proper level.
Page 213: Sales Code Ren - Multimedia System - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Operating Instructions - Satellite Radio Mode (If intended for home and other limited viewing uses only, Equipped) unless otherwise authorized by Macrovision. Reverse Refer to “Satellite Radio” in this section. engineering or disassembly is prohibited Operating Instructions - Video Entertainment DTS™...
Page 214: Operating Instructions - Satellite Radio
214 UNDERSTANDING YOUR INSTRUMENT PANEL A 20 gigabyte Hard Drive (HDD) allows uploads of models a dual display screen operation. Refer to your music and photos from CDs or through the USB port. Radio Specific User’s Manual for detailed operating While the Gracenote database finds the artist, track, and instructions.
Page 215: Operating Instructions - Hands-Free Communication (Uconnect™) (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 215 4. To move the minute forward, touch the screen where Operating Instructions — Hands-Free Communication (UConnect™) (If Equipped) the word “Min” with the arrow pointing upward is Refer to “Hands-Free Communication (UConnect™)” in displayed. To move the minute backward, touch the Section 3 of this manual for detailed operating instruc- screen where the word “Min”...
Page 216 216 UNDERSTANDING YOUR INSTRUMENT PANEL 3. When this feature is on, a check mark will appear in Changing the Time Zone the box next to the words “Daylight Savings.” Touch the 1. Turn on the system. screen where the words “Daylight Savings” are dis- played to change the current setting.
Page 217: Sales Code Rer - Multimedia System - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 217 The satellite navigation capability combines a Global- SALES CODE RER — MULTIMEDIA SYSTEM — IF EQUIPPED Positioning System-based navigation system with an integrated color screen to provide maps, turn identifica- NOTE: The sales code is located on the lower right side tion, selection menus, and instructions for selecting a of the unit’s faceplate.
Page 218: Operating Instructions - Satellite Radio
218 UNDERSTANDING YOUR INSTRUMENT PANEL rear seat passengers can watch a DVD on the optional Operating Instructions — Hands-Free rear-seat entertainment system while the driver and front Communication (UConnect™) (If Equipped) seat passenger listen to the radio. Refer to your “Navigation User’s Manual” for detailed operating instructions.
Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 219 Changing the Time Zone Changing Daylight Savings Time When selected, this feature will display the time of day in 1. Turn on the system. daylight savings time. Proceed as follows to change the 2. Touch the screen where the time is displayed. The current setting: clock setting menu will appear on the screen.
Page 220 220 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the screen where the time is displayed. The 6. To save the new time setting, touch the screen where clock setting menu will appear on the screen. If the words the word “Save” is displayed. “Time: User Clock”...
Page 221: Universal Consumer Interface (Uci) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 221 • the iPod battery charges when plugged into the UCI UNIVERSAL CONSUMER INTERFACE (UCI) — IF EQUIPPED connector. NOTE: This section is for sales code and REQ radios Connecting the iPod Device only with UConnect.™ For sales code REN touch screen Use the optional connection cable to connect an iPod to radio, refer to the separate User’s Manual.
Page 222: Play Mode
222 UNDERSTANDING YOUR INSTRUMENT PANEL Play Mode RW (Rewind) Button When switched to UCI mode the iPod will be in Play Press and hold the “RW” button to move backward in the mode. In this Play mode , you may use the following current track.
Page 223: List Or Browse Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 223 previous track in the list, if you press this button at any next song. To stop the SCAN mode and start playing the other time in the current track it will go back to the desired track, press the “SCAN”...
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL • 4 – Genres display, press the “TUNE/SCROLL” knob to select and start playing the track. By turning the “TUNE/SCROLL” • 5 - Audiobooks knob fast, you can jump through the list faster. During • 6 – Podcasts fast scroll, you may notice a slight delay in updating the information on the radio display.
Page 225: Satellite Radio (Rsc) - If Equipped (Rer/Req/Ren Radios Only)
UNDERSTANDING YOUR INSTRUMENT PANEL 225 can follow the same steps to go to the desired track in that System Activation list. Not all iPod sub menu levels are available on this Sirius Satellite Radio service is pre-activated, and you system. may begin listening immediately to the one year of SIRIUS audio service that is included with the factory- MUSIC TYPE Button...
Page 226: Electronic Serial Number/Sirius Identification Number (Ens/Sid)
226 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification Selecting Satellite Mode Press the SAT button until SAT appears in the display. A Number (ENS/SID) The Electronic Serial Number/Sirius Identification Num- CD may remain in the radio while in the Satellite radio ber is needed to activate your Sirius Satellite Radio mode.
Page 227: Reception Quality
UNDERSTANDING YOUR INSTRUMENT PANEL 227 SEEK Buttons Reception Quality Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
Page 228 228 UNDERSTANDING YOUR INSTRUMENT PANEL 3 seconds will make the radio display the Song Title all of By pressing the SEEK button when the Music Type the time (press and hold again to return to normal function is active, the radio will be tuned to the next display).
Page 229: Operating Instructions - Hands Free Phone (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 229 Select the button (1-6) you wish to lock onto this channel Buttons 1 - 6 and press and release that button. If a button is not These buttons tune the radio to the channels that you selected within 5 seconds after pressing the SET button, commit to push-button memory {12 Satellite stations}.
Page 230: Remote Sound System Controls - If Equipped
230 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF Right-Hand Switch Functions EQUIPPED • Press the top of the switch to increase the volume. The remote sound system controls are located on the rear • Press the bottom of the switch to decrease the volume. surface of the steering wheel.
Page 231: Left-Hand Switch Functions For Media (I.e. Cd) Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Left-Hand Switch Functions for Media (i.e. CD) RADIO OPERATION AND CELLULAR PHONES Operation Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from • Press the top of the switch once to listen to the next your radio.
Page 232: Climate Controls
232 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Do not apply paper, paper CD labels, or tape to the Manual Air Conditioning and Heating System disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5.
Page 233 UNDERSTANDING YOUR INSTRUMENT PANEL 233 Blower Control Temperature Control Rotate this control to regulate Rotate this control to regulate the amount of air forced the temperature of the air in- through the ventilation sys- side the passenger compart- tem in any mode. The blower ment.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Bi-Level Rotate this control to choose Air is directed through the panel and floor outlets. from several patterns of air distribution. You can select ei- NOTE: For all settings except full cold or full hot, there ther a primary mode as iden- is a difference in temperature between the upper and tified by the symbols on the...
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 235 Recirculation Control Air is directed through the floor, defrost, and side Press in on this button to window demist outlets. This setting works best in block the flow of outside air cold or snowy conditions that require extra heat to from coming into the passen- the windshield.
Page 236 236 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Air Conditioning Control • Continuous use of the recirculation mode may make Press in on this button to en- the inside air stuffy and window fogging may occur. gage the Air Conditioning. A Extended use of this mode is not recommended. light will illuminate when the Air Conditioning System is •...
Page 237: Economy Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 237 • ECONOMY MODE comfort levels desired by the driver and passenger. To If economy mode is desired, press the A/C button to turn accomplish this, the system gathers information from the off the indicator light and the A/C compressor. Then, cabin infrared sensor mounted between the sun-visors move the temperature control to the desired temperature.
Page 238 238 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Dial in the temperature NOTE: • The temperature setting can be adjusted at any time you would like the system to maintain by rotating the Tem- without affecting automatic operation. perature Control knob. Once •...
Page 239 UNDERSTANDING YOUR INSTRUMENT PANEL 239 Manual Operation The blower can be set to any fixed blower speed by This system offers a full complement of manual override rotating the Blower Control knob (on the left). features, which consist of Blower Preferred Automatic, NOTE: Please read the Automatic Temperature Control Mode Preferred Automatic, or Blower and Mode Pre- Operation Chart that follows for details.
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL...
Page 241 UNDERSTANDING YOUR INSTRUMENT PANEL 241 • Floor The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control NOTE: • When the ignition switch is turned to the LOCK Press this button to turn on the air conditioning during manual operation only. When the air position, the recirculation feature will be cancelled. conditioning is turned on, cool dehumidified air •...
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 243 • Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system in air-conditioned vehicles Mode by pressing the Recirculation Button. However, must be protected with a high-quality antifreeze coolant under certain conditions, while in Automatic Mode, to provide proper corrosion protection and to protect the system is blowing air out the defrost vents.
Page 244 244 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 245 UNDERSTANDING YOUR INSTRUMENT PANEL 245 Control Setting Suggestions for Various Weather Conditions...
Page 246 246 UNDERSTANDING YOUR INSTRUMENT PANEL REAR WINDOW FEATURES CAUTION! Electric Rear Window Defroster — If Equipped To avoid damaging the electrical conductors of the The electric Rear Window Defroster Control is rear window defroster, do not use scrapers, sharp located on the climate control. Press this button to instruments, or abrasive window cleaners on the turn on the rear window defroster and the heated side interior surface of the window.
Page 247 STARTING AND OPERATING CONTENTS Starting Procedures ..... 251 Automatic Transaxle Ignition Interlock System ..... . 257 Automatic Transaxle .
Page 248 248 STARTING AND OPERATING Power Steering ......270 Synchronizing ESP ....279 Driving On Slippery Surfaces .
Page 249 STARTING AND OPERATING 249 Life Of Tire ......295 3.5L Engine ......308 Replacement Tires .
Page 250 250 STARTING AND OPERATING Starting ......315 Loading ......321 Cruising Range .
Page 251: Starting Procedures
STARTING AND OPERATING 251 STARTING PROCEDURES WARNING! Before starting your vehicle, adjust your seat, the inside and outside mirrors, fasten your seat belt, and if present, Be sure to turn off the engine and remove the key instruct all other occupants to buckle their seat belts. from the ignition switch if you want to rest or sleep in your car.
Page 252: Normal Starting
252 STARTING AND OPERATING Normal Starting For vehicles equipped with Tip Start, turn the ignition switch to the START position and release it as soon as the NOTE: Normal starting of either a cold or a warm starter engages. The starter motor will continue to run, engine is obtained without pumping or depressing the and it will disengage automatically when the engine is accelerator pedal.
Page 253: If Engine Fails To Start
STARTING AND OPERATING 253 Without Tip Start If Engine Fails to Start If the engine fails to start after you have followed the WARNING! “Normal Starting” or “Extreme Cold Weather” proce- dures, it may be flooded. Push the accelerator pedal all •...
Page 254: After Starting
254 STARTING AND OPERATING seconds with the accelerator pedal pushed all the way to will disengage automatically in 10 seconds. Once this the floor. Release the accelerator pedal and the key once occurs, release the accelerator pedal, turn the ignition the engine is running smoothly.
Page 255: Engine Block Heater - If Equipped
STARTING AND OPERATING 255 ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSAXLE The engine block heater warms engine coolant and CAUTION! permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a Damage to the transaxle may occur if the following grounded, three-wire extension cord.
Page 256: Brake/Transaxle Interlock System
256 STARTING AND OPERATING Brake/Transaxle Interlock System WARNING! This system prevents you from moving the gear shift out • It is dangerous to shift the selector lever out of or if of “P” PARK and into any gear unless the brake pedal is the engine speed is higher than idle speed.
Page 257: Automatic Transaxle Ignition Interlock System
STARTING AND OPERATING 257 • Insert a key, screwdriver, or finger into the hole at the Automatic Transaxle Ignition Interlock System front of the cup holder and push and hold the manual This system prevents the key from being removed unless override release lever forward.
Page 258: Speed Or 6 Speed (Autostick ) Automatic Transaxle
258 STARTING AND OPERATING 4 Speed or 6 Speed (AutoStick ) Automatic Gear Ranges Transaxle “P” PARK The electronically controlled transaxle provides a precise “P” PARK supplements the parking brake by locking the shift schedule. The transaxle electronics are self- transaxle.
Page 259 STARTING AND OPERATING 259 REVERSE WARNING! Use this range for moving the vehicle rearward. Shift into this range only after the vehicle has come to a complete Never use PARK position on an Automatic Transaxle stop. as a substitute for the parking brake. Always apply parking brake fully when parked to guard against NEUTRAL vehicle movement and possible injury or damage.
Page 260 260 STARTING AND OPERATING DRIVE (OVERDRIVE) With 6–Speed Transaxle terrain, traveling into strong head winds or while towing This range should be used for most city and highway heavy trailers). Under these conditions, using the [3] driving. It provides the smoothest upshifts, downshifts, range will improve performance and extend transaxle life and best fuel economy.
Page 261 STARTING AND OPERATING 261 occur only to prevent engine overspeed while downshifts PARK, REVERSE, and NEUTRAL will continue to oper- occur earlier than other gear range selections. ate. This Reset feature allows the vehicle to be driven to a dealer for service without damaging the transaxle. CAUTION! In the event of a momentary problem, the transaxle can be reset to regain all forward gears by performing the...
Page 262: Autostick - If Equipped
262 STARTING AND OPERATING NOTE: Even if the transaxle can be reset, it is recom- mended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transaxle cannot be reset, dealer service is required. AUTOSTICK —...
Page 263: Autostick Operation
STARTING AND OPERATING 263 AutoStick Operation AutoStick General Information By placing the selector lever one shift-level below the D • You can start out in first or second gear. The system (Drive) position, it can be moved from side to side. This will ignore attempts to upshift at too low of a vehicle allows the driver to select a higher or lower range of speed.
Page 264: Parking Brake
264 STARTING AND OPERATING • Transaxle shifting will be more noticeable when PARKING BRAKE Autostick is engaged. The parking brake should always be applied when the driver is not in the vehicle. • If a low range is selected and the engine accelerates to the rev limit, the transaxle will automatically select the WARNING! next higher ratio.
Page 265 STARTING AND OPERATING 265 When parking on a hill, it is important to apply the parking brake before placing the gear selector lever in “P” (Park), otherwise the load on the transaxle locking mechanism may make it difficult to move the selector out of park.
Page 266 266 STARTING AND OPERATING • If the parking brake is applied while the vehicle is WARNING! moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle • Never leave children alone in a vehicle. Leaving has returned to a stop.
Page 267: Brake System
STARTING AND OPERATING 267 BRAKE SYSTEM WARNING! Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic • Riding the brakes can lead to brake failure and systems loses normal capability, the remaining possibly an accident. Driving with your foot rest- system will still function.
Page 268: Anti-Lock Brake System - If Equipped
268 STARTING AND OPERATING Anti-Lock Brake System — If Equipped You also may experience the following when the brake The Anti-Lock Brake System provides increased vehicle system goes into Anti-lock: stability and brake performance under most braking • The ABS motor running (it may continue to run for a conditions.
Page 269 STARTING AND OPERATING 269 All vehicle wheels and tires must be the same size and WARNING! type and tires must be properly inflated to produce • The Anti-Lock Brake System contains sophisticated elec- accurate signals for the computer. tronic equipment that may be susceptible to interference caused by improperly installed or high output radio trans- Anti-Lock Brake Light mitting equipment.
Page 270: Power Steering
270 STARTING AND OPERATING If both the Brake System Warning Light and the ABS NOTE: Increased noise levels at the end of the steering Light remain on, the Anti-Lock brakes (ABS) and Elec- wheel travel are considered normal and do not indicate tronic Brake Force Distribution (EBD) systems are not that there is a problem with the power steering system.
Page 271: Driving On Slippery Surfaces
STARTING AND OPERATING 271 CAUTION! WARNING! Prolonged operation of the steering system at the end Rapid acceleration on slippery surfaces is dangerous. of the steering wheel travel will increase the steering Unequal traction can cause sudden pulling of the fluid temperature and it should be avoided when front wheels.
Page 272: Driving Through Water
272 STARTING AND OPERATING 2. Slow down if road has standing water or puddles. Flowing/Rising Water 3. Replace tires when tread wear indicators first become WARNING! visible. Do not drive on or cross a road or a path where water 4.
Page 273 STARTING AND OPERATING 273 CAUTION! WARNING! • Always check the depth of the standing water before driving • Driving through standing water limits your vehi- through it. Never drive through standing water that is deeper cle’s traction capabilities. Do not exceed 5 mph (8 than the bottom of the tire rims mounted on the vehicle.
Page 274: Traction Control System (Tcs) - If Equipped
274 STARTING AND OPERATING TRACTION CONTROL SYSTEM (TCS) — IF TCS is active. If the indicator light flashes during accel- eration, ease up on the accelerator and apply as little EQUIPPED This system monitors the amount of wheel spin of each of throttle as possible.
Page 275: Brake Assist System (Bas) - If Equipped
STARTING AND OPERATING 275 BRAKE ASSIST SYSTEM (BAS) — IF EQUIPPED WARNING! This system complements the Anti-Lock Brake System (ABS) by optimizing the vehicle braking capability dur- • The BAS cannot prevent the natural laws of phys- ing emergency braking maneuvers. This system detects ics from acting on the vehicle, nor can it increase an emergency braking situation by sensing the rate and braking efficiency beyond that afforded by the...
Page 276: Electronic Stability Program (Esp) - If Equipped
276 STARTING AND OPERATING • Oversteer - when the vehicle is turning more than ELECTRONIC STABILITY PROGRAM (ESP) — IF appropriate for the steering wheel position. EQUIPPED This system enhances directional control and stability of • Understeer - when the vehicle is turning less than the vehicle under various driving conditions.
Page 277: Esp Operating Modes
STARTING AND OPERATING 277 ESP Operating Modes WARNING! The ESP system has two available operating modes: • The ESP cannot prevent the natural laws of phys- ESP On ics from acting on the vehicle, nor can it increase This is the normal operating mode for ESP. Whenever the the traction afforded by prevailing road condi- vehicle is started the ESP system will be in this mode.
Page 278: Esp/Bas Malfunction Indicator Light And Esp/Tcs Indicator Light
278 STARTING AND OPERATING When in “Partial Off” mode, the engine torque reduction WARNING! feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable. However, a fea- In the Partial Off mode, the engine torque reduction ture of the system remains active. This feature controls is cancelled and the stability features are desensi- wheel spin across an axle quite similarly to a limited slip tized.
Page 279: Synchronizing Esp
STARTING AND OPERATING 279 • The ESP Control System will make buzzing or clicking The system will turn the “ESP/BAS Malfunction Indica- tor Light” on continuously while the engine running if it sounds when it is active. This is normal; the sounds detects a malfunction in either the ESP or the BAS or will stop when ESP becomes inactive following the both.
Page 280: Tire Safety Information
280 STARTING AND OPERATING • European Metric tire sizing is based on European TIRE SAFETY INFORMATION design standards. Tires designed to this standard have Tire Markings the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 281 STARTING AND OPERATING 281 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 282 282 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions (i.e., tire pressure, vehicle loading, road conditions,...
Page 283: Tire Identification Number (Tin)
STARTING AND OPERATING 283 located on the white sidewall side of the tire. Look for the Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, TIN on the outboard side of black sidewall tires as mounted however, the date code may only be on one side.
Page 284: Tire Loading And Tire Pressure
284 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire and Loading Information Placard This placard tells you important information about: 1) the number of people that can be carried in the vehicle...
Page 285 STARTING AND OPERATING 285 Loading occupants and cargo should never exceed XXX kg or XXX The vehicle maximum load on the tire must not exceed lbs.” on the Tire and Loading Information placard. The the load carrying capacity of the tire on your vehicle. You combined weight of occupants, cargo/luggage and will not exceed the tire’s load carrying capacity if you trailer tongue weight (if applicable) should never exceed...
Page 286 286 STARTING AND OPERATING 4. The resulting figure equals the available amount of manual to determine how this reduces the available cargo and luggage load capacity. For example, if “XXX” cargo and luggage load capacity of your vehicle. amount equals 1400 lbs. and there will be five 150 lb. NOTE: The following table shows examples on how to passengers in your vehicle, the amount of available cargo calculate total load, cargo/luggage, and towing capaci-...
Page 287 STARTING AND OPERATING 287...
Page 288: Tires - General Information
288 STARTING AND OPERATING 1. Safety— WARNING! WARNING! Overloading of your tires is dangerous. Overloading • Improperly inflated tires are dangerous and can cause can cause tire failure, affect vehicle handling, and accidents. increase your stopping distance. Use tires of the •...
Page 289: Tire Inflation Pressures
STARTING AND OPERATING 289 2. Economy— maximum loaded vehicle condition. These pressure con- Improper inflation pressures can cause uneven wear ditions will be found in the “Supplemental Tire Pressure patterns to develop across the tire tread. These abnormal Information” section of this manual. wear patterns will reduce tread life resulting in a need for earlier tire replacement.
Page 290 290 STARTING AND OPERATING check tire pressure. Do not make a visual judgement Check tire pressures more often if subject to a wide range when determining proper inflation. Radial tires may look of outdoor temperatures, as tire pressures vary with properly inflated even when they are under inflated.
Page 291: Radial-Ply Tires
STARTING AND OPERATING 291 Tire Pressures for High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 292: Compact Spare Tire - If Equipped
292 STARTING AND OPERATING Compact Spare Tire — If Equipped CAUTION! The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style Prolonged use of limited use spare, or an incorrect vehicle only.
Page 293: Limited Use Spare - If Equipped
STARTING AND OPERATING 293 CAUTION! WARNING! Because of the reduced ground clearance, do not take The limited use spare tires are for emergency use your vehicle through an automatic car wash with the only. Installation of this limited use spare tire affects compact spare installed.
Page 294: Tire Spinning
294 STARTING AND OPERATING WARNING! WARNING! Prolonged use of limited use spare, or incorrect tire Fast spinning tires can be dangerous. Forces gener- size of front wheel, may damage the transaxle differ- ated by excessive wheel speeds may cause tire dam- ential and result in loss of vehicle mobility and could age or failure.
Page 295: Life Of Tire
STARTING AND OPERATING 295 Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread.
Page 296: Replacement Tires
296 STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little WARNING! exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. • Do not use a tire, wheel size or rating other than that specified for your vehicle.
Page 297: Alignment And Balance
STARTING AND OPERATING 297 Improper alignment will not cause vehicle vibration. CAUTION! Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and Replacing original tires with tires of a different size avoid tire cupping and spotty wear. may result in false speedometer and odometer readings.
Page 298: Snow Tires
298 STARTING AND OPERATING SNOW TIRES TIRE ROTATION RECOMMENDATIONS Some areas of the country require the use of snow tires Tires on the front and rear axles of vehicles operate at during winter. Standard tires are of the all season type different loads and perform different steering, driving, and satisfy this requirement as indicated by the M+S and braking functions.
Page 299: Tire Pressure Monitor System (Tpms) - If Equipped
STARTING AND OPERATING 299 The suggested rotation method is the “forward-cross” when the outside temperature decreases, the tire pres- shown in the following diagram. sure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
Page 300 300 STARTING AND OPERATING • The TPM System will continue to warn the driver of − For example, your vehicle may have a recom- low tire pressure as long as the condition exists, and mended cold (parked for more than 3 hours) placard will not turn off until the tire pressure is at or above pressure of 30 psi (207 kPa).
Page 301 STARTING AND OPERATING 301 NOTE: CAUTION! • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire • The TPMS has been optimized for the original failure or condition. equipment tires and wheels. TPMS pressures and warning have been established for the tire size •...
Page 302: Base System - If Equipped
302 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings and the TPMS will monitor the actual tire pressure in The Tire Pressure Monitoring Telltale Light will the tire. illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or Base System —...
Page 303 STARTING AND OPERATING 303 repeat, providing the system fault still exists. The Tire 2. If you install the compact spare tire in place of a road Pressure Monitoring Telltale Light will turn off when the tire that has a pressure below the low-pressure warning fault condition no longer exists.
Page 304: Premium System - If Equipped
304 STARTING AND OPERATING Premium System — If Equipped Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitor System (TPMS) uses wireless The Tire Pressure Monitoring Telltale Light will technology with wheel rim mounted electronic sensors to illuminate in the instrument cluster and a chime monitor tire pressure levels.
Page 305 STARTING AND OPERATING 305 Should this occur, you should stop as soon as possible, and inflate the tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flash- ing, and the Tire Pressure Monitoring Telltale Light will...
Page 306 306 STARTING AND OPERATING 1. Jamming due to electronic devices or driving next to Light will remain ON, a chime will sound, and the EVIC facilities emitting the same Radio Frequencies as the TPM will still display a flashing pressure value in the graphic sensors.
Page 307: General Information
STARTING AND OPERATING 307 TPM Telltale Light will turn OFF and the graphic in the The tire pressure sensors are covered under one of the EVIC will display a new pressure value instead of dashes following licenses: (- -), as long no tire pressure is below the low-pressure warning limit in any of the four active road tires.
Page 308: 3.5L Engine
308 STARTING AND OPERATING 3.5L Engine Poor quality gasoline can cause problems such as hard The 3.5L engine is designed to meet all starting, stalling, and hesitations. If you experience these emissions regulations and provide satisfac- symptoms, try another brand of gasoline (with the ap- tory fuel economy and performance when propriate octane rating for your engine) before consider- using high-quality unleaded gasoline hav-...
Page 309: Reformulated Gasoline
STARTING AND OPERATING 309 Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” For vehicles equipped with a 2.4L or 3.5L engine, DO NOT use gasoline containing Methanol or E85 Etha- Reformulated gasolines contain oxygenates, and are spe- nol.
Page 310: Mmt In Gasoline
310 STARTING AND OPERATING MMT In Gasoline Materials Added to Fuel MMT is a manganese containing metallic additive that is All gasoline sold in the United States is required to blended into some gasoline to increase octane. Gasoline contain effective detergent additives. Use of additional blended with MMT provides no performance advantage detergents or other additives is not needed under normal beyond gasoline of the same octane number without...
Page 311: Carbon Monoxide Warnings
STARTING AND OPERATING 311 • An out-of-tune engine, or certain fuel or ignition Carbon Monoxide Warnings malfunctions, can cause the catalytic converter to WARNING! overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or Carbon monoxide (CO) in exhaust gases is deadly.
Page 312: Flexible Fuel- 2.7L Engines Only (Except California Emission States)
312 STARTING AND OPERATING • Guard against carbon monoxide with proper mainte- vehicles. Please refer to the other sections of this manual nance. Have the exhaust system inspected every time for information on features that are common between the vehicle is raised. Have any abnormal conditions Flexible Fuel and gasoline only powered vehicles.
Page 313: Ethanol Fuel (E-85)
STARTING AND OPERATING 313 ETHANOL FUEL (E-85) CAUTION! E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Only vehicles with the E-85 fuel filler door label can operate on E-85. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury.
Page 314: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
314 STARTING AND OPERATING For best results, a refueling pattern that alternates be- Selection Of Engine Oil For Flexible Fuel Vehicles tween E-85 and unleaded gasoline should be avoided. (E-85) and Gasoline Vehicles When you do switch fuels, it is recommended that: FFV vehicles operated on E85 require specially formu- lated engine oils.
Page 315: Starting And Operating 315
STARTING AND OPERATING 315 Starting CAUTION! The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0° F (-18° C). In Replacing fuel system components with non-ethanol the range of 0° F (-18° C) to 32° F (0° C), you may compatible components can damage your vehicle.
Page 316: Adding Fuel
316 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) As a reminder, a fuel icon with an arrow indicating which side of the vehicle the fuel filler door is located on, is located in the instrument cluster, just below the Fuel Gage. The gas cap is located behind the fuel filler door on the left rear of the vehicle.
Page 317 STARTING AND OPERATING 317 After removing the gas cap, lay the cap tether in the hook CAUTION! on the inside of the fuel door. This keeps the gas cap suspended away from the vehicle’s surface. • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
Page 318: Loose Fuel Filler Cap Message
318 STARTING AND OPERATING properly. The Malfunction Indicator Light in the in- WARNING! strument cluster may turn on if the gas cap is not secured properly. Make sure that the gas cap is tight- • Never have any smoking materials lit in or near ened each time the vehicle is refueled.
Page 319: Vehicle Loading
STARTING AND OPERATING 319 • Month and year of manufacture VEHICLE LOADING The load carrying capacity of your vehicle is shown on • Gross Vehicle Weight Rating (GVWR) the “Vehicle Certification Label.” This information • Gross Axle Weight Rating (GAWR) front should be used for passenger and luggage loading as indicated.
Page 320: Gross Axle Weight Rating (Gawr)
320 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Overloading The GAWR is the maximum capacity of the front and rear The load carrying components (axle, springs, tires, axles. Distribute the load over the front and rear axles wheels, etc.) of your vehicle will provide satisfactory evenly.
Page 321: Loading
STARTING AND OPERATING 321 Loading Vehicle with a GVWR of 4480 To load your vehicle properly, first figure out its empty EXAMPLE ONLY Front Axle Rear Axle weight, axle by axle and side by side. Store heavier items Empty Weight 1853 lbs 1631 lbs down low and be sure you distribute their weight as...
Page 322: Trailer Towing
322 STARTING AND OPERATING TRAILER TOWING Gross Vehicle Weight Rating (GVWR) In this section, you will find safety tips and information The Gross Vehicle Weight Rating (GVWR) is the total on limits to the type of towing you can reasonably do allowable weight of your vehicle.
Page 323 STARTING AND OPERATING 323 weighed in combination. (Note that GCWR ratings in- Tongue Weight (TW) clude a 150 lbs (68 kg) allowance for the presence of a Tongue Weight (TW) is the downward force exerted on driver). the hitch ball by the trailer. In most cases it should not be less than or more than 10% of the trailer load.
Page 324: Trailer Hitch Classification
324 STARTING AND OPERATING Trailer Hitch Classification Trailer Hitch Classification The following chart provides the industry standard for Class Max. GTW (Gross Trailer the maximum trailer weight a given trailer hitch class can Wt.) tow and should be used to assist you in selecting the Class I - Light Duty 2,000 lbs (907 kg) correct trailer hitch for your intended towing condition.
Page 325: Trailer Towing Weights (Maximum Trailer Weight Ratings)
Tire engine with automatic transaxle. Please refer to the and Loading Information placard. Refer to “Tire Safety following website, http://www-5.chrysler.com/ Information” in Section 5 of this manual. searchapp/ui.jsp or your dealer for additional informa- tion.
Page 326: Trailer And Tongue Weight
326 STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
Page 327: Towing Requirements
STARTING AND OPERATING 327 NOTE: Remember that everything put into or on the Towing Requirements trailer adds to the load on your vehicle. Also, additional To promote proper break-in of your new vehicle driv- factory-installed options, or dealer-installed options, etrain components the following guidelines are recom- must be considered as part of the total load on your mended: vehicle.
Page 328 328 STARTING AND OPERATING • Safety chains must always be used between your WARNING! vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the Improper towing can lead to an injury accident. chains under the trailer tongue and allow enough Follow these guidelines to make your trailer towing slack for turning corners.
Page 329 STARTING AND OPERATING 329 4. Tongue weight rating for the trailer hitch utilized Information” in this section for information on tread (This requirement may limit the ability to always wear indicators and for proper inspection procedure. achieve 10% of tongue weight as a percentage of total −...
Page 330 330 STARTING AND OPERATING − Trailer brakes are recommended for trailers over 1,000 WARNING! lbs (450 kg) and required for trailers in excess of 2,000 lbs (907 kg). Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- CAUTION! tem and cause it to fail.
Page 331: Towing Tips
STARTING AND OPERATING 331 Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping,...
Page 332 332 STARTING AND OPERATING Towing Tips — Automatic Transaxle Towing Tips — Electronic Speed Control (If The “D” range can be selected when towing. However, if Equipped) frequent shifting occurs while in this range, the “3” range − Don’t use in hilly terrain or with heavy loads. should be selected.
Page 333: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 333 − Air Conditioning RECREATIONAL TOWING (BEHIND Turn off temporarily. MOTORHOME, ETC.) − Refer to “Cooling System” under “Maintenance Pro- TOWING THIS VEHICLE BEHIND ANOTHER cedures” in Section 7 of this manual for more informa- VEHICLE (Flat towing with all four wheels on the tion.
Page 335: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....336 Jump-Starting Procedures ....344 If Your Engine Overheats .
Page 336: Hazard Warning Flasher
336 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER NOTE: With extended use, the Hazard Warning Flash- The Hazard Flasher switch is located in the Instrument ers may wear down your battery. Panel Switch Bank above the climate controls. IF YOUR ENGINE OVERHEATS Push and release the switch to turn on the Hazard In any of the following situations, you can reduce the Warning Flashers.
Page 337: Engine Oil Overheating - 2.4L Engine Only (If Equipped)
WHAT TO DO IN EMERGENCIES 337 the fan control to High. This allows the heater core to act WARNING! as a supplement to the radiator and aids in removing heat A hot engine cooling system is dangerous. You or from the engine cooling system. others could be badly burned by steam or boiling coolant.
Page 338: Jacking And Tire Changing
338 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the WARNING! edge of the roadway as possible. Avoid icy or slippery • Do not attempt to change a tire on the side of the areas.
Page 339: Jack Location
WHAT TO DO IN EMERGENCIES 339 6. Block both the front and rear Spare Tire Removal of the wheel diagonally opposite Lift up the load floor cover and remove the hold down. the jacking position. For ex- ample, if changing the right front tire, block the left rear wheel.
Page 340: Jacking Instructions
340 WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly.
Page 341 WHAT TO DO IN EMERGENCIES 341 Jacking Locations...
Page 342 342 WHAT TO DO IN EMERGENCIES head is properly engaged with the lift area closest to the CAUTION! wheel to be changed. Do not raise the vehicle until you are sure the jack is securely engaged. Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3.
Page 343 WHAT TO DO IN EMERGENCIES 343 and wheel nuts with the cone shaped end of the nuts 8. Finish tightening the nuts. Push down on the wrench toward the wheel. Lightly tighten the nuts. To avoid the while tightening the wheel nuts. Alternate nuts, until risk of forcing the vehicle off the jack, do not tighten the each nut has been tightened twice.
Page 344: Jump-Starting Procedures
344 WHAT TO DO IN EMERGENCIES 10. Place the deflated (flat) tire in the cargo area, have the JUMP-STARTING PROCEDURES tire repaired or replaced as soon as possible. WARNING! WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised.
Page 345 WHAT TO DO IN EMERGENCIES 345 1. Wear eye protection and remove any metal jewelry WARNING! such as watchbands or bracelets that might make an inadvertent electrical contact. • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin, or cloth- 2.
Page 346 346 WHAT TO DO IN EMERGENCIES 3. Turn off the heater, radio, and all unnecessary electri- cal loads. 4. Remove the protective cover over the remote jump- start positive battery post (+) in the engine compartment. Connect one end of the jumper cable to the positive battery post.
Page 347 WHAT TO DO IN EMERGENCIES 347 7. Start the engine in the vehicle that has the booster NOTE: Refer to “Maintenance Procedures” in Section 7 battery, let the engine idle a few minutes, and then start of this manual for information on accessing the battery the engine in the vehicle with the discharged battery.
Page 348: Freeing A Stuck Vehicle
348 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE WARNING! If your vehicle becomes stuck in mud, sand, or snow, it Fast spinning tires can be dangerous. Forces gener- can often be moved by a rocking motion. Turn your ated by excessive wheel speeds may cause axle and steering wheel right and left to clear the area around the tire damage or failure.
Page 349: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 349 TOWING A DISABLED VEHICLE TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the WITHOUT THE IGNITION KEY ground) Special care must be taken when the vehicle is towed with the ignition in the LOCK position. Flat bed towing With The Ignition Key is the preferred towing method.
Page 350: Towing This Vehicle Behind Another Vehicle With A Tow Dolly
350 WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER CAUTION! VEHICLE WITH A TOW DOLLY Rear towing is not recommended with the front wheels • If the vehicle being towed requires steering, the on the ground, as transaxle damage can result. If rear ignition switch must be in the ON position, not in towing is the only alternative, a front end dolly must be the LOCK or ACC position.
Page 351 MAINTAINING YOUR VEHICLE CONTENTS 2.4L Engine Compartment ....354 Maintenance Procedures ....361 2.7L Engine Compartment .
Page 352 352 MAINTAINING YOUR VEHICLE A/C Air Filter — If Equipped ... . 370 Front And Rear Wheel Bearings ... 387 Power Steering —...
Page 353 MAINTAINING YOUR VEHICLE 353 Front Fog Light ..... . 403 Fluids And Capacities ....409 Tail/Stop Light, Rear Turn Signal Light, Fluids, Lubricants, And Genuine Parts .
Page 354: 2.4L Engine Compartment
354 MAINTAINING YOUR VEHICLE 2.4L ENGINE COMPARTMENT...
Page 355: L Engine Compartment
MAINTAINING YOUR VEHICLE 355 2.7L ENGINE COMPARTMENT...
Page 356: 3.5L Engine Compartment
356 MAINTAINING YOUR VEHICLE 3.5L ENGINE COMPARTMENT...
Page 357: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 357 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 358: Loose Fuel Filler Cap Message
358 MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message EMISSIONS INSPECTION AND MAINTENANCE If the vehicle diagnostic system determines that the fuel PROGRAMS filler cap in loose, improperly installed, or damaged, a In some localities, it may be a legal requirement to pass “gASCAP”...
Page 359 MAINTAINING YOUR VEHICLE 359 Your vehicle has a simple ignition key-actuated test, ignition key or start the engine. This means that your which you can use prior to going to the test station. To vehicle’s OBD system is not ready and you should not check if your vehicle’s OBD system is ready, you must do proceed to the I/M station.
Page 360: Replacement Parts
360 MAINTAINING YOUR VEHICLE vehicle serviced before going to the I/M station. The I/M NOTE: Intentional tampering with emissions control station can fail your vehicle because the MIL symbol is on systems can result in civil penalties being assessed with the engine running. against you.
Page 361: Maintenance Procedures
MAINTAINING YOUR VEHICLE 361 The best time to check the engine oil level is about 5 MAINTENANCE PROCEDURES The pages that follow contain the required maintenance minutes after a fully warmed engine is shut off. Do not services determined by the engineers who designed your check oil level before starting the engine after it has sat vehicle.
Page 362 362 MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
Page 363: Engine Oil Selection
MAINTAINING YOUR VEHICLE 363 Engine Oil Selection Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L For best performance and maximum protection under all Engines types of operating conditions, the manufacturer recom- SAE 5W-20 engine oil is recommended for all operating mends engine oils that are API Certified and meet the temperatures.
Page 364 364 MAINTAINING YOUR VEHICLE Lubricants which do not have both, the engine oil certi- Materials Added To Engine Oils fication mark and the correct SAE viscosity grade num- The manufacture strongly recommends against the addi- ber should not be used. tion of any additives (other than leak detection dyes) to the engine oil.
Page 365: Engine Oil Filter
MAINTAINING YOUR VEHICLE 365 Engine Oil Filter Spark Plugs The engine oil filter should be replaced at every engine Spark plugs must fire properly to assure engine perfor- oil change. mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be Engine Oil Filter Selection replaced if there is any malfunction due to a faulty spark All of this manufacturer’s engines have a full-flow type...
Page 366: Catalytic Converter
366 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- WARNING! verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure The air induction system (air cleaner, hoses, etc) can proper catalyst operation and prevent possible catalyst provide a measure of protection in the case of engine damage.
Page 367: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 367 NOTE: Intentional tampering with emissions control To minimize the possibility of catalyst damage: systems can result in civil penalties being assessed • Do not shut off the engine or interrupt the ignition against you. when the transaxle is in gear and the vehicle is in motion.
Page 368 368 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Don’t allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 369: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 369 Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer • Use only refrigerants and compressor lubricants at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 370: A/C Air Filter - If Equipped
370 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling The A/C Air Filter is located in the fresh air inlet behind R-134a Air Conditioning Refrigerant is a hydrofluorocar- the glove box. Perform the following procedure to re- bon (HFC) that is endorsed by the Environmental Pro- place the filter: tection Agency and is an ozone-saving product.
Page 371: Power Steering - Fluid Check
MAINTAINING YOUR VEHICLE 371 5. Disengage the two retaining tabs that secure the filter 7. Install the A/C Air Filter with the arrow on the filter cover to the HVAC housing and remove the cover. pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover.
Page 372: Front Suspension Ball Joints
372 MAINTAINING YOUR VEHICLE apparent, and/or the system is not functioning as antici- Front Suspension Ball Joints pated. Coordinate inspection efforts through a certified There are two front suspension lower ball joints that are DaimlerChrysler Dealership. permanently lubricated. Inspect these ball joints when other maintenance is performed.
Page 373: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 373 attention should also be given to hood latching compo- Operation of the wipers on dry glass for long periods nents to insure proper function. When performing other may cause deterioration of the wiper blades. Always use underhood services, the hood latch, release mechanism, washer fluid when using the wipers to remove salt or dirt and safety catch should be cleaned and lubricated.
Page 374: Windshield Washers
374 MAINTAINING YOUR VEHICLE Windshield Washers Exhaust System The best protection against carbon monoxide entry into NOTE: Refer to the appropriate “Engine Compartment” the vehicle body is a properly maintained engine exhaust diagram in Section 7 for the location of the windshield system.
Page 375: Cooling System
MAINTAINING YOUR VEHICLE 375 Cooling System WARNING! WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. • When working near the radiator cooling fan, dis- Breathing it can make you unconscious and can connect the fan motor lead or turn the ignition eventually poison you.
Page 376 376 MAINTAINING YOUR VEHICLE Coolant Checks Cooling System — Drain, Flush, and Refill Check engine coolant (antifreeze) protection every 12 The system should be drained, flushed, and refilled at the months (before the onset of freezing weather, where intervals shown in the “Maintenance Schedule” in Sec- applicable).
Page 377 MAINTAINING YOUR VEHICLE 377 Adding Coolant CAUTION! Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This • Mixing of coolants other than specified HOAT coolant can be used up to 5 Years or 100,000 miles (160 engine coolants, may result in engine damage and 000 km) before replacement.
Page 378 378 MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deion- The cap should be inspected and cleaned if there is any ized water when mixing the water/engine coolant accumulation of foreign material on the sealing surfaces. solution.
Page 379 MAINTAINING YOUR VEHICLE 379 Disposal of Used Engine Coolant 6 Cylinder Engines — the level of the coolant in the Used ethylene glycol based engine coolant is a regulated pressurized coolant bottle should be between the substance requiring proper disposal. Check with your “COLD”...
Page 380 380 MAINTAINING YOUR VEHICLE • Maintain coolant concentration at 50% HOAT engine humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to coolant (minimum) and distilled water for proper enter the radiator. corrosion protection of your engine, which contains aluminum components.
Page 381: Hoses And Vacuum/Vapor Harnesses
MAINTAINING YOUR VEHICLE 381 Hoses and Vacuum/Vapor Harnesses Fuel System Inspect surfaces of hoses and nylon tubing for evidence Electronic Fuel Injection high-pressure fuel systems are of heat and mechanical damage. Hard or soft spots, designed with tubes and special connects, connections, brittle rubber, cracking, tears, cuts, abrasions, and exces- and clamps which have unique material characteristics to sive swelling indicate deterioration of the rubber...
Page 382 382 MAINTAINING YOUR VEHICLE Inspect all hose clamps and couplings to make sure they WARNING! are secure and no leaks are present. Riding the brakes can lead to brake failure and NOTE: • Often, fluids such as oil, power steering fluid, and possibly an accident.
Page 383 MAINTAINING YOUR VEHICLE 383 Clean the top of the master cylinder area before removing WARNING! the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reser- Worn brake hoses can burst and cause brake failure. voir.
Page 384: Automatic Transaxle
384 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Overfilling the brake fluid reservoir can result in Do not allow petroleum base fluid to contaminate the spilling brake fluid on hot engine parts and the brake fluid, all brake seal components could be brake fluid catching fire.
Page 385 MAINTAINING YOUR VEHICLE 385 Fluid Level Check — Vehicles with 2.4L and 2.7L driven at least 15 miles (24 km). Hot fluid cannot be held Engines comfortably between the fingertips. Cold fluid is at a Use the following procedure to check the automatic temperature below 80°F (27°C).
Page 386 386 MAINTAINING YOUR VEHICLE Fluid and Filter Changes CAUTION! Change the automatic transaxle fluid and filter at the intervals shown in the “Maintenance Schedule” in this • Using a transmission fluid other than the manu- manual. facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque In addition, change the fluid and filter if the transaxle is converter shudder.
Page 387: Front And Rear Wheel Bearings
MAINTAINING YOUR VEHICLE 387 The following maintenance recommendations will enable Front and Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. you to obtain maximum benefit from the corrosion No regular maintenance is required for these compo- resistance built into your vehicle. nents.
Page 388 388 MAINTAINING YOUR VEHICLE Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- Do not use abrasive or strong cleaning materials such hicle in the shade using Mopar Car Wash or a mild as steel wool or scouring powder, which will scratch car wash soap, and rinse the panels completely with metal and painted surfaces.
Page 389 MAINTAINING YOUR VEHICLE 389 • If your vehicle is damaged due to an accident or heavy soil and/or excessive brake dust, use Mopar similar cause, which destroys the paint and protective Wheel Cleaner (05066247AB) or equivalent or select a coating, have your vehicle repaired as soon as pos- nonabrasive, non-acidic cleaner.
Page 390 390 MAINTAINING YOUR VEHICLE Mopar Spot & Stain Remover if absolutely necessary. Do WARNING! not use harsh cleaners or Armorall. Use Mopar Total Clean to clean vinyl upholstery Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in Cleaning Leather Upholstery closed areas they may cause respiratory harm.
Page 391 MAINTAINING YOUR VEHICLE 391 • For grease stains, apply Mopar Multi-Purpose Glass Surfaces Cleaner to a clean, damp cloth and remove stain. Use All glass surfaces should be cleaned on a regular basis a fresh, damp towel to remove soap residue. with Mopar Glass Cleaner or any commercial household-type glass cleaner.
Page 392: Cleaning The Center Console Cup Holders
392 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be Cleaning The Center Console Cup Holders used, but do not use high alcohol content or abrasive Removal cleaners. If soap is used, wipe clean with a clean damp Grab the rubber portion of the cup holder and lift rag.
Page 393: Convertible Top Care
MAINTAINING YOUR VEHICLE 393 General Cleaning CONVERTIBLE TOP CARE Careful vacuuming of the top before washing is helpful Soft Top in removing dust and other foreign particles. Wash in Immediate removal of any contaminant is recommended. partial shade instead of direct sun. Wet the entire vehicle Regular washing of the top will enhance its life and before washing the top.
Page 394 394 MAINTAINING YOUR VEHICLE Scrub in all directions, covering an area of about two Additional Cleaning Procedure square feet at a time. Avoid heavy scrubbing. Rinse the For additional cleaning assistance in removing stubborn entire vehicle with water to remove all soap and dirt from stains, apply Mopar Convertible Cloth Top Cleaner # the top fabric and to prevent streaking on painted and 4883061 to the complete stain, extending 2 inches (50...
Page 395: Weather Strip Care - Soft & Hard Top
MAINTAINING YOUR VEHICLE 395 FUSES (TOTALLY INTEGRATED POWER CAUTION! MODULE) The Totally Integrated Power Module (TIPM) is located Avoid getting Scotchguard on the surrounding in the engine compartment near the air cleaner assembly. weather strips, moldings, paint, or glass. Damage to This center contains fuses and relays.
Page 396 396 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 40 Amp — Battery Feed — — 30 Amp Ignition Off Draw Green Power Top Module Green (IOD) Sense 2 — 20 Amp — 40 Amp —...
Page 397 MAINTAINING YOUR VEHICLE 397 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 40 Amp — Battery Feed — Ra- — 10 Amp Ignition Run — Cli- Green diator Fan Relay mate Controls/Hot Cup Holder - if —...
Page 398 398 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse — 10 Amp Ignition Run — Occu- 30 Amp — Auto Shutdown pant Classification Pink (ASD) Relay Feed 1 Module (OCM)/ — 10 Amp Battery Feed —...
Page 399 MAINTAINING YOUR VEHICLE 399 Cavity Cartridge Mini Description CAUTION! Fuse Fuse • When installing the Totally Integrated Power 40 Amp — Battery Feed — Anti- Green Lock Brakes (ABS) Module cover, it is important to ensure the cover is Module - if properly positioned and fully latched.
Page 400: Vehicle Storage
400 MAINTAINING YOUR VEHICLE VEHICLE STORAGE NOTE: For lighted switches, see your dealer for replace- If you will not be using your vehicle for more than 21 ment instructions. days you may want to take steps to preserve your battery. You may: LIGHTS BULBS —...
Page 401: Bulb Replacement
MAINTAINING YOUR VEHICLE 401 BULB REPLACEMENT Low Beam Headlight, High Beam Headlight 1. Open the hood. NOTE: It may be necessary to remove the air cleaner filter housing and position the totally integrated power module aside prior to replacing the low beam headlight on the driver’s side of the vehicle.
Page 402: Front Turn Signal/Park Light
402 MAINTAINING YOUR VEHICLE Front Turn Signal/Park Light CAUTION! 1. Open the hood. Do not touch the new bulb with your fingers. Oil 2. Rotate the bulb’s electrical connector ⁄ turn counter- contamination will severely shorten bulb life. If the clockwise and remove it from the headlight housing.
Page 403: Front Fog Light
MAINTAINING YOUR VEHICLE 403 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlight housing and rotate the connector ⁄ turn clock- wise to lock it in place. Front Fog Light NOTE: Access to the lights through the lower fascia cutout is limited.
Page 404: Backup Light
404 MAINTAINING YOUR VEHICLE 2. Remove the bulb from the connector socket and install Tail/Stop Light, Rear Turn Signal Light, Backup the replacement bulb. Light The taillights are a two-piece design. The tail/stop lights CAUTION! and rear turn signal lights are located in the rear corner body panels.
Page 405 MAINTAINING YOUR VEHICLE 405 2. Remove the two plastic wing nuts from the taillight 4. Rotate the applicable bulb’s electrical connector ⁄ housing. turn counterclockwise and remove it from the taillight housing. Location Plastic Wing Nuts 3. Grasp the taillight housing with one hand on the 1 —...
Page 406 406 MAINTAINING YOUR VEHICLE 5. Remove the bulb from the connector socket and install the replacement bulb. 6. Install the bulb and connector assembly into the taillight housing and rotate the connector ⁄ turn clock- wise to lock it in place. 7.
Page 407: License Plate Light
MAINTAINING YOUR VEHICLE 407 2. Gently pry the lens loose. License Plate Light 1. Remove the two retaining screws from the lens. 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the lens and the two retaining screws. Location and Removal of Rear License Light Lens...
Page 408: Center High-Mounted Stop Light (Chmsl)
408 MAINTAINING YOUR VEHICLE Center High-Mounted Stop Light (CHMSL) 3. Disconnect the bulb from the harness connector and then connect the replacement bulb. 1. Open the trunk lid. 4. Install the bulb and connector assembly into the 2. Rotate the bulb’s electrical connector ⁄...
Page 409: Fluids And Capacities
MAINTAINING YOUR VEHICLE 409 FLUIDS AND CAPACITIES Engine U.S. Metric Fuel (approximate) All Engines 16.9 gallons 64 liters Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 quarts 4.26 liters 2.7L Engine (SAE 5W-20, API Certified) 5.5 quarts 5.2 liters 3.5L Engine (SAE 10W-30, API Certified) 5.5 quarts...
Page 410: Fluids, Lubricants, And Genuine Parts
410 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluids, Lubricants, and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Engine Coolant Organic Additive Technology) or equivalent Use API Certified engine oil. SAE 5W-20 is recommended. Refer to the en- Engine Oil (2.4L &...
Page 411 MAINTAINING YOUR VEHICLE 411 Component Fluids, Lubricants, and Genuine Parts Spark Plugs (2.4L) ZFR5F-11 (Gap.044 in [1.12 mm]) Spark Plugs (2.7L) RE14PMC5 (Gap.050 in [1.27 mm]) Spark Plugs (3.5L) ZFR5LP-13G (Gap.050 in [1.27 mm]) Fuel Selection (2.4L & 2.7L) 87 Octane Fuel Selection (2.7L - EXCEPT CALI- E-85 Ethanol FORNIA EMISSION STATES)
Page 412 412 MAINTAINING YOUR VEHICLE Chassis Component Fluids, Lubricants and Genuine Parts Automatic Transaxle Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not Brake Master Cylinder available, then DOT 4 is acceptable. Use only recommended brake fluids. Power Steering Reservoir Mopar ATF+4 Automatic Transmission Fluid.
Page 413 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..414 Required Maintenance Intervals ... 417 Maintenance Schedule ....414...
Page 414 414 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The “Scheduled” maintenance services, listed in bold The oil change indicator system will remind you that it is type must be done at the times or mileages specified to time to take your vehicle in for scheduled maintenance. assure the continued proper functioning of the emission On Electronic Vehicle Information Center (EVIC) control system.
Page 415 MAINTENANCE SCHEDULES 415 NOTE: dealer, the message can be reset by referring to the steps • The oil change indicator message will not monitor the described under “Oil Change Required” under “Elec- time since the last oil change. Change your vehicles oil tronic Vehicle Information Center (EVIC)”...
Page 416 416 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals CAUTION! as required.
Page 417 MAINTENANCE SCHEDULES 417 Required Maintenance Intervals Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the engine oil and engine oil filter. 6,000 10 000 Rotate the tires. 6,000 10 000 If using your vehicle in dusty or off-road conditions,...
Page 418 418 MAINTENANCE SCHEDULES Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Replace the spark plugs on 2.4L engines (except 30,000 50 000 PZEV* engine). Inspect and adjust the power steering pump belt ten- 30,000 50 000 sion on 2.4L engines.
Page 419 MAINTENANCE SCHEDULES 419 Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Replace the timing belt on 2.4L and 3.5L engines. 102,000 170 000 Change the automatic transaxle fluid & filter. 120,000 200 000 Replace the accessory drive belt on 2.7L engines.
Page 421 IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For In Mexico Contact ..... 424 Your Vehicle ......423 Customer Assistance For The Hearing Or Prepare For The Appointment .
Page 422 422 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....428 Traction Grades ..... . 429 Department Of Transportation Uniform Tire Temperature Grades .
Page 423: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 423 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items, and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 424: Daimlerchrysler Motors Corporation Customer Center
424 IF YOU NEED CONSUMER ASSISTANCE • Vehicle Identification Number (VIN) special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to your authorized DaimlerChrysler Motors Corporation Customer dealer’s service manager first.
Page 425: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 425 contract, call the manufacturer’s Service Contract Na- Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) tional Customer Hotline at 1-800-521-9922. To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
Page 426: Warranty Information (U.s. Vehicles Only)
426 IF YOU NEED CONSUMER ASSISTANCE WARRANTY INFORMATION (U.S. Vehicles Only) WARNING! See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to Engine exhaust, some of its constituents, and certain this vehicle. vehicle components contain or emit chemicals known to the State of California to cause cancer and MOPAR PARTS birth defects or other reproductive harm.
Page 427: Reporting Safety Defects
IF YOU NEED CONSUMER ASSISTANCE 427 To contact NHTSA, you may either call the Auto Safety REPORTING SAFETY DEFECTS Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– In the 50 United States and Washington D.C. 9153), or go to http://www.safercar.gov; or write to: If you believe that your vehicle has a defect which could Administrator, NHTSA, 400 Seventh Street, SW., Wash- cause a crash or cause injury or death, you should...
Page 428: Publication Order Forms
428 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals PUBLICATION ORDER FORMS To order the following manuals, you may use either the Filled with diagrams, charts and detailed illustrations, website or the phone numbers listed below. Visa, Mas- these practical manuals make it easy for students and tercard, American Express, and Discover orders are ac- technicians to find and fix problems on computer- cepted.
Page 429: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 429 Call Toll Free at: All passenger car tires must conform to Federal safety requirements in addition to these grades. • 1–800–890–4038 (U.S.) Treadwear • 1–800–387–1143 (Canada) The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled con- ditions on a specified government test course.
Page 430 430 IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and material of the tire to degenerate and reduce tire life, and concrete. A tire marked C may have poor traction perfor- excessive temperature can lead to sudden tire failure. The mance.
Page 431 INDEX...
Page 432 432 INDEX About Your Brakes ....264,267 Airbag Maintenance ..... . . 58 ABS (Anti-Lock Brake System) .
Page 433 INDEX 433 Automatic Dimming Mirror ....96 Battery ....... 367 Automatic Door Locks .
Page 434 434 INDEX Fluid Check ..... . . 383,412 Carbon Monoxide Warning ....74,311 Hoses .
Page 435 INDEX 435 Cleaning Convertible ......81 Wheels ......389 Convertible Top .
Page 436 436 INDEX Cup Holder ......164,392 Dipsticks Heated/Cooled (Beverage Holder) ..164 Automatic Transaxle .
Page 437 INDEX 437 Electric Remote Mirrors ....98 Engine ......72,354,355,356 Electrical Power Outlets .
Page 438 438 INDEX Oil Synthetic ......364 Filters Operation ......72 Air Cleaner .
Page 439 INDEX 439 Flooded Engine Starting ....253 Additives ......310 Floor Console .
Page 440 440 INDEX Garage Door Opener (HomeLink ) ... 155 Hands-Free Phone (UConnect™) ..99,217,218 Gas Cap (Fuel Filler Cap) ... . 316,318,358 Hard Drive (HDD) .
Page 441 INDEX 441 Time Delay ......140 Ignition Key Removal ..... 12 Heated Mirrors .
Page 442 442 INDEX Jacking Instructions ..... . 340 Leaks, Fluid ......76 Jump Starting .
Page 443 INDEX 443 Engine Temperature Warning ....178 Map Reading ......144 Exterior .
Page 444 444 INDEX Auto Unlock ......31 Methanol ......309 Automatic Door .
Page 445 INDEX 445 Occupant Restraints ....39,53,54,56 Oil Filter, Change ......365 Octane Rating, Gasoline (Fuel) .
Page 446 446 INDEX Phone, Cellular ....99,217,218 Pregnant Women and Seat Belts ....47 Phone, Hands-Free (UConnect™) .
Page 447 INDEX 447 Rear Window Features ....246 Replacement Tires ..... . . 296 Reception, Radio .
Page 448 448 INDEX Seat Belt Maintenance ....392 Height Adjustment ..... 134 Seat Belt Reminder .
Page 449 INDEX 449 Side Airbag ......54 Remote ......27 Side View Mirror Adjustment .
Page 450 450 INDEX Tachometer ......178 Flat Changing ..... . 338,344 Taillights .
Page 451 INDEX 451 To Open Hood ......137 Trailer and Tongue Weight ....326 Tongue Weight/Trailer Weight .
Page 452 452 INDEX Transmitter, Garage Door Opener Universal Serial Bus (USB) Port ... 213,217 (HomeLink ) ......155 Universal Transmitter .
Page 453 INDEX 453 Warning Lights Windows ......32 (Instrument Cluster Description) ... . . 176 Power .
Page 454 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS / ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key RemovalKey-In-Ignition ReminderSENTRY KEY Replacement KeysSentry Key ProgrammingGeneral InformationSECURITY ALARM SYSTEM - IF EQUIPPED Rearming of the SystemTo Arm the SystemTo Disarm the SystemILLUMINATED ENTRY SYSTEM - IF EQUIPPED REMOTE KEYLESS ENTRY To unlock the doorsTo lock the doorsConvertible Top OperationTo Unlatch the TrunkExpress Down Window FeatureUsing The Panic AlarmProgramming Additional TransmittersBattery ReplacementGeneral InformationREMOTE STARTING SYSTEM - IF EQUIPPED How To Use Remote StartDOOR LOCKS Manual Door LocksPower Door LocksWINDOWS Power WindowsWind BuffetingTRUNK LOCK AND RELEASE TRUNK SAFETY WARNING Trunk Emergency Release OCCUPANT RESTRAINTS Lap/Shoulder BeltsLap/Shoulder Belt Untwisting ProcedureSeat Belt PretensionersEnhanced Seat Belt Reminder System (BeltAlert) Automatic Locking ModeSeat Belts And Pregnant WomenSeat Belt ExtenderDriver and Front Passenger Supplemental...

Chrysler Sebring Convertible Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler Sebring Convertible

Summary of Contents for Chrysler Sebring Convertible