Keurig Platinum Plus B79 Owner's Manual page 6

Set-Up & First Brew (continued)
SECTION 1
Rinse Cycle
Your Brewer is equipped with a rinse cycle to flush out residual flavors that
may be left from hot cocoa or flavored K-Cup ® portion packs.
1. Place a mug on the Drip Tray Plate. If you've just completed a rinse or hot
water cycle, proceed to step 4.
Lift the Handle and check the K-Cup Holder to make sure there is
2. ®
no portion pack inserted.
3. Lower the Handle completely. The LCD Control Center will indicate
"READY TO BREW."
4. Press the RINSE Button. During the rinse cycle, the Extra-Small Cup
icon will appear on the LCD Control Center.
The rinse cycle will dispense about 4 oz. of hot water into your mug. Once
5.
complete, discard the contents of the mug.
Following the rinse cycle, your Brewer may display "NOT READY" as it
heats water for the next brew cycle. After your Brewer indicates "READY
TO BREW", the RINSE and HOT WATER Buttons will be available for use for
about one minute. During this time, you can perform another rinse cycle or
dispense hot water without lifting the Handle. After this time, the Brewer will
return to idle mode.
NOTE: To brew directly after a rinse cycle, lift the Handle, insert a portion pack
and brew as normal.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge
the water from the inner tank.
1. If there is water in the Water Reservoir, remove the Lid, then lift the
Water Reservoir straight up and away from Brewer. Discard water, rinse
and refill with water. Place the Water Reservoir back on the Brewer and
replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2. Be sure the Brewer is turned on. Raise and lower the Handle on the
Brewer without inserting a portion pack.
The LCD Control Center will display "READY TO BREW."
3.
Brew a Travel Mug (11.25 oz. serving) of water (do not use a portion pack).
4. Repeat steps 2 and 3 two more times to completely purge water from
inner tank.
If you are experiencing any problems with your Brewer, please contact
Customer Service at 1.866.901.BREW (2739).
10
SECTION 2
Controls & Indicators (LCD Control Center)
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in
the LCD Control Center.
NOTE: You must set the clock if you will be using the
Auto On/Off Time programming feature.
10 1. Press the MENU Button.
fig.
2. The word 'OFF' will appear at the top of the
LCD Control Center to indicate that the
H M
clock is not set (fig. 10). The programming
options will appear on the LCD Control
SET CLOCK
AUTO OFF
ONOFF TIME
Center with a small arrow pointing to 'SET
BREW TEMP
BREW SIZE
CLOCK.' "H" (Hour) will appear above the
MENU
Left Button and "M" (Minute) will appear
above the Right Button. The "H" and "M"
icons and Left and Right Buttons will flash.
Set
Press or hold the Left Button under the
Minutes 3.
Set
Hours
flashing "H" until you have reached the
appropriate hour. If the hour has passed
12 "PM" will be shown.
Press or hold the Right Button under the
4.
flashing "M" to set the minutes.
5. When you have reached the correct time,
press the MENU Button six times to scroll
through the remaining programming steps.
6. The correct time should now be displayed in the LCD Control Center.
NOTE: If power is interrupted to the Brewer by unplugging it, or if power is
lost, follow the procedure above to reset the time as the clock will not be
visible until the time is set. Brew size and brew temperature menu settings
are remembered and restored automatically. All other settings will be
restored automatically after clock is set.
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea
or hot cocoa on your own schedule. By programming your Brewer to turn on
each morning, you will never have to wait for the Brewer to warm up to brew
a gourmet cup of coffee. It will take the Brewer approximately 4 minutes to
warm up from room temperate.
The Brewer can be left on all the time so that it is
1. Leave it ON all the time.
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To
turn the Brewer off at any time, simply press and release the Power Switch.
(NOTE : Although the clock remains on, if set, you can not brew a cup of coffee,
tea or hot cocoa.) Press and release the Power Switch again to restore
power to the Brewer. You will have to wait for the water to heat up before
the Brewer is ready to brew.
2. Set the Brewer to "AUTO OFF" following a specified period of time after the
last brew.
a. Press the MENU Button twice to program the Auto Off feature. The LCD
Control Center will now display the programming options with a small
arrow next to "SET AUTO OFF" (fig. 11).
11