Keurig Platinum Plus B79 Owner's Manual page 5

Set-Up & First Brew (continued)
SECTION 1
c. Once size is chosen, press BREW Button.
BREW Button will remain illuminated, Left
and Right Buttons will no longer be lit and
Extra-Small Cup
icon of brew size will be lit.
(3.25 oz.)
Large Mug
(9.25 oz.) 7. The LCD Control Center will now display the
Small Cup word 'BREWING' and the serving size you
(5.25 oz.)
selected will be illuminated on LCD (fig. 8).
CAUTION: There is extremely hot water in
Travel Mug
(11.25 oz.)
the K-Cup Holder during the brew process.
®
Small Mug
(7.25 oz.) To avoid risk of injury, do not lift the Handle or
open the K-Cup ® Assembly Housing during the
brew process.
8. There may be a short pause prior to coffee
being dispensed. The entire brew process
8
fig.
lasts for approximately 1 minute and ends
with a burst of air to remove all liquid from
the K-Cup ® portion pack.
BREWING
Lift the Handle, remove
9.
and dispose of the
used portion pack.
CAUTION: Portion pack
MENU
will be hot.
Enjoy your first cup
10.
of Keurig Brewed
®
gourmet coffee, tea
or hot cocoa!
11. Your Brewer may display "NOT READY" as it heats water for the next
brew cycle. The "READY TO BREW" indication will return to the LCD
Control Center in about 15 seconds.
Stopping the Brew Process
If you need to stop the brewing after the process has started, press and
release the Power Switch to turn the Brewer 'OFF.' The flow of coffee, tea
or hot cocoa will stop, the heating element will shut off and the blue lights
illuminating the LCD Control Center and Water Reservoir will disappear.
NOTE: You may get more coffee, tea or hot cocoa in your cup during your next
brew. We recommend that you perform a cleansing brew with water-only after
a terminated brew. Then your NEXT brew will be the volume you have selected.
adding Water
9
fig.
The LCD Control Center of your Brewer will
indicate when the water level in the tank is low
NOT READY
or if the Water Reservoir has been removed by
ADD
WATER
displaying the words "ADD WATER" (fig. 9). The
blue light in the Water Reservoir will also blink
MENU
when water needs to be added. The Brewer will
not allow you to brew when "ADD WATER" is
MENU
displayed (fig. 9).
8
The Water Reservoir can be filled in two ways.
Lift off the Water Reservoir Lid and pour water directly into the Water
1.
Reservoir while it is still attached to the Brewer, then replace the Lid.
2. Remove the Water Reservoir from Brewer by first removing Lid from the
Water Reservoir, then lifting the Water Reservoir straight up and toward
front of Brewer. Fill with water. Place the Water Reservoir back on the
Brewer and replace the Lid.
IMPORTANT: Do not remove the Water Reservoir during the brewing process.
Brewing Iced Beverages
Your iced tea and iced coffee taste best when fresh-brewed hot over ice.
Try it by placing a tall cup filled with ice on the Drip Tray Plate, choose
your favorite K-Cup portion pack, select the brew size and press the
®
BREW Button. Also, look for the Brew Over Ice icon on portion packs
™
that are specially crafted to brew over ice!
IMPORTANT: Do not brew into a cup made of glass. Doing so may cause the
glass to crack or break.
Dispensing hot Water
Your Brewer can dispense hot water for instant soup, oatmeal or other needs.
1. Place a mug on the Drip Tray Plate. If you've just completed a rinse or hot
water cycle, proceed to step 4.
2. Lift the Handle and check the K-Cup ® Holder to make sure there is no
portion pack inserted.
Lower the Handle completely. The LCD Control Center will indicate
3.
"READY TO BREW."
4. All brew size icons are lit with the default size flashing. To choose a
different size, press the Left Button to go down in size or Right Button to
go up in size.
Once size is chosen, press the HOT WATER Button. While the hot water
5.
cycle is in progress, the selected brew size icon will be displayed on the
LCD Control Center.
Following the hot water cycle, your Brewer may display "NOT READY" as it
heats water for the next brew cycle. After your Brewer indicates "READY
TO BREW," the RINSE and HOT WATER Buttons will be available for use
for about one minute. During this time, you can dispense another cup of
hot water or perform a rinse cycle without lifting the Handle. After this
time, the Brewer will return to idle mode.
NOTE: To brew directly after a hot water cycle, lift the Handle, insert a portion
pack and brew as normal.
9