Download  Print this page

Important Safety Instruction; Electrical Requirements - Kenmore 24" (61 cm) Wall Oven Installation Instructions Manual

Electric wall oven
Hide thumbs

Advertisement

Important
Notes
to the
Installer
1.
Read all instructions contained in these installation
instructions before installing the wall oven.
2.
Remove all packing material from the oven
compartments before connecting the electrical supply
to the wall oven.
3.
Observe all governing codes and ordinances.
4.
Be sure to leave these instructions with the consumer.
5.
Oven door may be removed to facilitate installation.
6.
THESE OVENS ARE NOT APPROVED FOR
STACKABLE OR SIDE=BY=SIDEINSTALLATION.
Important
Note
to the
Consumer
Keep these instructions with your Use and Care Guide for
future reference.
Optional
Item Available:
= A Decorative Filler Trim Kit for upper opening:
- Black : 903063-9100
- White : 903063-9101
This kit can be ordered for purchase by calling at a
Service Center. The phone number is located at the
back of your Use and Care Guide.
IMPORTANT
SAFETY
INSTRUCTION
• Be sure your wall oven is installed and grounded
properly
by a qualified
installer or service
technician.
• This wall oven must be electrically
grounded
in
accordance
with
local codes or, in their absence,
with the National
Electrical Code ANSI/NFPA
No.70= latest edition
in United States, or with CSA
Standard
C22.1, Canadian
Electrical Code, Part 1, in
Canada.
Stepping,
leaning
or sitting
on the
door of this wall oven can result in serious injuries
and can also cause damage
to the wall oven.
Never use your wall oven for warming
or heating
the room. Prolonged use of the wall oven without
adequate ventilation can be dangerous.
The electrical
power to the oven must
be shut off while
line connections
are being made.
Failure to do so could result in serious
injury or
death.
1. Carpentry
Refer to figure 1 or 2 for the dimensions applicable to
your appliance, and the space necessary to receive the
oven. The oven support surface may be solid plywood or
similar material, however the surface must be level from
side to side and front to rear.
2. Electrical
Requirements
Theses appliances must be supplied with the proper
voltage and frequency, and connected to an individual,
properly grounded branch circuit, protected by a circuit
breaker or fuse, having amperage as noted on the rating
plate (the rating plate is located on the oven frame).
Observe all governing
codes and local ordinances
1.
A 3-wire or 4-wire single phase 120/208 or 120/240
Volt, 60 Hz AC only electrical supply is required on
a separate circuit fused on both sides of the line
(time-delay fuse or circuit breaker is recommended).
DO NOT fuse neutral. The fuse size must not exceed
the circuit rating of the appliance specified on the
nameplate.
NOTE: Wire sizes and connections must conform with
the fuse size and rating of the appliance in accordance
with the American National Electrical Code ANSI/NFPA
No. 70-latest edition, or with Canadian CSA Standard
C22.1, Canadian Electrical Code, Part 1, and local codes
and ordinances.
An extension
cord should
not be used
with this appliance.
Such use may result in a fire,
electrical
shock, or other personal injury.
2.
These appliances should be connected to the fused
disconnect (or circuit breaker) box through flexible
armored or nonmetallic sheathed cable. The flexible
armored cable extending from the appliance should
be connected directly to the junction box. The
junction box should be located as shown in figure 1
or 2 with as much slack as possible remaining in the
cable between the box and the appliance, so it can
be moved if servicing is ever necessary.
3.
A suitable strain relief must be provided to attach
the flexible armored cable to the junction box.
Electrical
Shock
Hazard
Electrical
ground
is required
on this appliance.
Do not connect
to the electrical
supply
until
appliance
is permanently
grounded.
Disconnect
power
to the junction
box before
making the electrical
connection.
This
appliance
must
be
connected
to
a
grounded,
metallic,
permanent
wiring
system,
or a grounding
connector
should
be connected
to the grounding
terminal
or wire
lead on the
appliance,
Do not use a gas supply
line for grounding
the
appliance.
Failure to do any of the above could result in a
fire, personal injury or electrical
shock.

Advertisement

loading

  Related Manuals for Kenmore 24" (61 cm) Wall Oven

This manual is also suitable for:

30" (76.2 cm) wall oven27" (68.6 cm) wall oven