Table of Contents
Advertisement
Quick Links
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-981
Retain This
Manual for
Reference
100322
OWNER'S
MANUAL
®
MARCY
HOME GYM
IMPEX
2801 S. Towne Ave., Pomona, CA 91766
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
MWM 981
®
INC.
Advertisement
Table of Contents
Related Manuals for Impex MWM-981
Summary of Contents for Impex MWM-981
- Page 1 Safety Notice MARCY MWM 981 Hardware Pack HOME GYM Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM-981 Retain This Manual for Reference 100322 ® OWNER'S IMPEX INC. 2801 S. Towne Ave., Pomona, CA 91766 MANUAL Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com...
-
Page 2: Table Of Contents
ORDERING PARTS..................………… 23 BEFORE YOU BEGIN ® Thank you for selecting the MARCY MWM-981 HOME GYM by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 3: Important Safety Notices
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. -
Page 4: Warning Label Replacement
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. -
Page 5: Hardware Identifier
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. - Page 6 HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
-
Page 7: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert the two Guide Rods (#11) through Rubber Bumpers and into the holes on the Rear Stabilizer. - Page 8 DIAGRAM 1...
- Page 9 STEP 2 (See Diagram 2) A.) Attach the holes on the Upper Frame (#1) onto the Guide Rods (#11). Place the Upper Frame onto the Vertical Frame (#4). B.) Secure the Upper Frame to the Guide Rods with two M10 x 1” Allen Bolts (#64) and Ø ¾” Washers (#73).
- Page 10 DIAGRAM 2...
- Page 11 STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#8) to the Upper Frame (#1). Secure it with one 8 ½” Front Press Axle (#19), two Ø 1” x Ø 5/8” Washers (#75), and two M10 Aircraft Nuts (#70). Do not over tighten the Nuts.
- Page 12 DIAGRAM 3...
- Page 13 STEP 4 (See Diagram 4) A.) Insert the Front Press Handle (#12) into the hole on Right Butterfly (#10) and Left Butterfly (#9). Secure each Handle with one M8 x ¾” Allen Bolt (#61) and one Ø 5/8” Curved Washer (#76). B.) Insert 15 ¾”...
- Page 14 STEP 5 (See Diagram 5) A.) Attach one Swivel Pulley Bracket (#17) to the open bracket on the back of Vertical Frame (#4). Secure it with one M10 x 2 ½” Allen Bolt (#66), two Ø ¾” Washers (#73), and one M10 Aircraft Nut (#70). Do not over tighten the Nut and Bolt. Make sure the Swivel Pulley Bracket can swivel freely.
- Page 15 STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the 126” Upper Cable (#32) to the front open bracket under the Upper Frame (#1). B.) Attach a Pulley (#35) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#62), two Ø...
- Page 16 DIAGRAM 6...
- Page 17 STEP 7 (See Diagram 7& Cable Loop Diagram) A.) Hook one end of the 98” Butterfly Cable (#34) to Right Butterfly (#10). B.) Draw the Cable towards the right open Swivel Pulley Bracket (#17). C.) Attach a Pulley (#35) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#62), two ¾” Washers (#73), and one M10 Aircraft Nut (#70).
- Page 18 STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach the 164” Lower Cable (#33) to the open bracket on the Base Frame (#3). B.) Attach a Pulley (#35) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#62), two ...
- Page 19 DIAGRAM 8...
- Page 20 STEP 9 (See Diagram 9) A.) Attach Lat Bar (#14) to the Upper Cable (#32) with two Hooks (#53) and one 15-link Chain (#54) when doing Lat Pull exercises. B.) Attach Shiver Bar (#15) to the Lower Cable (#33) use the two Hooks (#53) and the 15-link Chain (#33) from Lat Bar when doing Arm Curl exercises C.) Replace Shiver Bar with the Ankle Strap (#52) or Single Handle (#78) to the Lower Cable for various exercises.
- Page 21 Set up the Lock Combination A.) The combination is pre-set to 0-0-0 by the factory. B.) Turn the dials to 0-0-0 and aligned to the Combination Set Up Line. C.) Pull out the shackle and turn 180 D.) Press down on the shackle. E.) Turn the dials (aligned to the Combination Set Up Line) to your desired combination.
-
Page 22: Parts List
PARTS LIST KEY NO. DESCRIPTION Q’ty Upper Frame Selector Stem Rear Stabilizer Ankle Strap Base Frame Hook Vertical Frame 15-link Chain Seat Support 2” x 2” End Cap Vertical Seat Support Ø 1” x 3/8” Bushing Leg Developer Ø 1” x Ø 5/8” Pulley Bushing Front Press Base M10 x 2 3/8”... -
Page 23: Resistance Chart
MWM981 WEIGHT RESISTANCE CHART Weight Plate Front Butterfly Developer Press Pull Pulley Note: Each plate weights 10 lbs. Numbers are approximate. Actual weights may vary. Values for Butterfly are for each arm. -
Page 24: Warranty
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.