Related Manuals for Myson iV080
Summary of Contents for Myson iV080
- Page 1 Specifiers Guide. iVECTOR Heater/Cooler Models: iV080, iV100, iV120, iV140, iV160 heatingthroughinnovation.
-
Page 3: Table Of Contents
Contents Contents Introduction iVECTOR Benefits Compact in Size Renewable Technology Rapid Response Low Surface Temperature (LST) iVECTOR Specification Data Unit Sizes Outputs Flow Rates/Pressure Losses Noise Levels Hydronic Connections Weight, Water Content and Motor Power iVECTOR Installation Ease of Installation Mounting Dimensions Water Connection - Pipe Routing Options Electrical Connection... -
Page 4: Introduction
Introduction 1.0 Introduction The iVECTOR is MYSON’s latest product innovation and an traditional advantages of a fan convector with a range of new exciting, energy efficient addition to our range of modern product benefits made possible by the inclusion of our latest heating solutions. -
Page 5: Ivector Benefits
(Please note that this does not apply when iVECTORs are used outer part of an iVECTOR will exceed a temperature of 43°C. As with high water temperature systems, please contact MYSON a result, when used with heat pumps, iVECTORs provide a high Technical Services for full information). -
Page 6: Ivector Specification Data
The heat output of the iVECTOR is affected by the flow rate of reasonable, as shown in the outputs table. For quietest water through its heat exchanger, even when the mean water operation MYSON recommends sizing the iVECTOR based on temperature is constant. Each iVECTOR model requires the normal fan speed. -
Page 7: Flow Rates/Pressure Losses
ISO 3741. For quietest speed, the lower the noise level. At the lowest fan speed, the operation MYSON recommends sizing the iVECTOR based on unit operates almost silently. It is our quietest fan convector ever. -
Page 8: Ivector Installation
150mm. Units should not be installed in locations in kit form – there is only a one-piece casing to attach! with high humidity levels, such as bathrooms. 4.2 Mounting Dimensions Dimensions (mm) Model iV080 iV100 1000 iV120 1200 iV140... -
Page 9: Water Connection - Pipe Routing Options
iVECTOR Installation 4.3 Water Connection - Pipe Routing Options The iVECTOR has two pipes to connect – flow and return. This Please note that the flow pipe must be connected to the pipework can be routed in one of two ways, either from the floor bottom connection of the heat exchanger and the return pipe or through the wall at the back of the unit (see diagram below). - Page 10 iVECTOR Installation 4.4 Electrical Connection (continued...) 2-pipe 0 valve CONTROL POWER BOARD BOARD Supply 230V 50Hz WATER SENSOR 2-PIPE SENSOR TRANSFORMER 2-pipe 1 valve CONTROL POWER Supply 230V 50Hz BOARD BOARD 24V 50Hz 24V DC Supply 230V 50Hz WATER SENSOR 2-PIPE SENSOR TRANSFORMER...
-
Page 11: Applications
With a full range of hydronic heat emitters, electric heat emitters Our technical team are happy to provide expert advice on and controls, MYSON is the UK’s leading expert in the control system design and help you make the best decisions on heating and distribution of heat. -
Page 12: Intelligent And Easy To Use Controls
Intelligent and Easy to Use Controls 6.1 Introduction The intelligent, electronic control system provided as standard in incorporates an ‘easy’ mode for everyday operation and a ‘full’ every iVECTOR includes a wide range of easy to use heating and mode for more advanced functions. It also has the ability to link cooling operating options. -
Page 13: Easy Mode
Intelligent and Easy to Use Controls 6.2 Easy Mode Every iVECTOR leaves the factory with its controls set to the 2. Comfort setting - the iVECTOR will run indefinitely in this simplest level (easy mode). This setting allows you to set the setting with the fan speed automatically adjusting as required. -
Page 14: Full Mode
Intelligent and Easy to Use Controls 6.3 Full Mode The full mode operation has the same four functions as easy 7. Frost setting - provides frost protection or overheat mode plus a further four others: protection during periods of absence. 5. -
Page 15: Building Management System (Bms)
Intelligent and Easy to Use Controls 6.4 Building Management System (BMS) Each iVECTOR has a built-in BMS connection, this must be wired to the main BMS controller to allow the BMS to take control of the iVECTOR. 2-pipe 1 valve + BMS 24V AC BUILDIN G MANAGEMENT... - Page 16 MYSON Eastern Avenue, Team Valley, Gateshead, Tyne & Wear NE11 0PG, UK 0845 402 3434, 0191 491 7568, sales@myson.co.uk, www.myson.co.uk heatingthroughinnovation.
Need help?
Do you have a question about the iV080 and is the answer not in the manual?
Questions and answers