Daewoo DTC-29G1 Instruction Manual page 12

Channel skipping
- You can select skip „YES" or „NO" using the re-
mote control RED „Skip" button (A11). A pro-
gram with skip „YES" doesn't appear on screen
when changing channels with the PROGRAM
UP (A6) / DOWN (A21) buttons.
Manual Channel Tuning
Choose a starting point.
- Select with „Program" the program from which
you want to start manual tuning. Then the chan-
nel number, the frequency, the name and the
program number of this program are displayed
in the Install menu.
TV system modification
If necessary, you can modify the TV system :
- Select „system" function.
- Adjust choosing between FRANCE (L/L'), GB (I),
EURO (B/G), E/ EURO (D/K) systems.
Then, the program displayed on the screen is
changed to the chosen system.
Channel deleting
- Select the program to delete using the re-
mote control CURSOR UP (A6) / DOWN (A21)
buttons.
- Press the remote control YELLOW „Delete" but-
ton (A26). The deleted program is moved to
program number 99 with skip changed to „YES".
The existing 99 program is moved to program
number 98 and so on.
Channel searching
- Select the „Frequency" function.
- Press, and hold for more than 1second, the re-
mote control CURSOR RIGHT (A20) [LEFT (A7)]
buttons to start up [down] manual tuning.
- Searching will stop automatically at the next
channel found (to stop tuning, press the re-
mote control MENU button (A19)).
Note: You can directly locate a program by
entering the data into the „channel" or
the „frequency" function.
Perform fine tuning
- If you are unable to get a good picture or rea-
sonable quality sound due to poor reception,
it is possible to perform fine tuning.
- Select the „frequency" function.
- Press, for less than 1 second, the remote con-
trol CURSOR RIGHT(A20) [LEFT(A7)] buttons
to perform up [down] fine tuning in steps of
0.05MHz (50 kHz).
Channel order changing
- Select the program to move using the remote
control CURSOR UP (A6) / DOWN (A21) but-
tons.
- Press the remote control GREEN „Move" button
(A12): the program line background is high-
lighted in green, and can be moved to another
position using the remote control CURSOR UP
(A6)/ DOWN (A21) buttons.
- When the desired position is reached, confirm
the new position pressing the remote control
GREEN „Confirm" button (A12). Then the program
line background will return again to grey.
Enter station name
It is possible to enter your own choice of name
for each program. You can change an existing
name, or enter a name where none exists. If none
exists „- - - - - - -" will be shown in the Install menu,
and program status display ( see the section
PROGRAM STATUS DISPLAY on page 8).
- Select the „NAME" function.
- Select one of the 7 character positions by us-
ing the remote control CURSOR RIGHT (A20) /
LEFT (A7) buttons to move the cursor.
- Then use the CURSOR UP (A6) /DOWN (A21)
buttons to select the desired character for
that position.
- Repeat the last two instructions for other po-
sitions, as desired.
- Once the name has been entered, press the
OK button (A18) to store it. The name will be
memorised to the program number currently
shown on the „Store To" line. The „Store To" pro-
gram number will highlight in red briefly.
Store program in memory
- Select the „store to" function
- Enter the program number you want to store
to either by using the remote control CUR-
SOR RIGHT (A20) / LEFT (A7) buttons, or di-
rectly by using the remote control NUMBER
0...9 buttons (A3).
- Press the OK button (A18) to confirm.
Remarks: this function can also be used if you
want to copy a program already memo-
rised to another program number.
12