HP BladeSystem c3000 Quickspecs page 16

QuickSpecs
Configuration Information Factory Integrated Models
HP BladeSystem HP BladeSystem HP BladeSystem HP BladeSystem
c-Class FC SAN c-Class FC SAN c-Class FC SAN c-Class FC SAN
Interconnects Interconnects Interconnects Interconnects
HP BladeSystem HP BladeSystem HP BladeSystem HP BladeSystem
InfiniBand Interconnects InfiniBand Interconnects InfiniBand Interconnects InfiniBand Interconnects
Step 4: Select rack power distribution for installing the enclosure into a rack. Step 4: Select rack power distribution for installing the enclosure into a rack. Step 4: Select rack power distribution for installing the enclosure into a rack. Step 4: Select rack power distribution for installing the enclosure into a rack.
NOTE: For use with the c3000 rack-able model only. NOTE: NOTE: NOTE:
NOTE: A pair of PDUs must be ordered for AC Feed redundancy. If AC redundancy is not required, a single PDU or UPS may be NOTE: NOTE: NOTE:
acceptable.
HP Monitored Power HP Monitored Power HP Monitored Power HP Monitored Power
Distribution Unit Distribution Unit Distribution Unit Distribution Unit
HP Modular PDU HP Modular PDU HP Modular PDU HP Modular PDU
HP UPS HP UPS HP UPS HP UPS
Step 5: Select Wall Outlet Power Cords Step 5: Select Wall Outlet Power Cords Step 5: Select Wall Outlet Power Cords Step 5: Select Wall Outlet Power Cords
NOTE: NOTE: Select one wall outlet power cord for each power supply when plugging the power supplies into a wall outlet. NOTE: NOTE:
NOTE: Wall Outlet power cords should only be used with low-line (100v to 110V) power sources. If high-line power outlets are NOTE: NOTE: NOTE:
required, safety regulations require the use of a PDU or a UPS between the c3000 enclosures power supplies and wall outlets.
NOTE: A standard PDU power cord(c13 to C14) is included with each AC power supply, so these wall outlet power cords are not NOTE: NOTE: NOTE:
required if you plan to plug the power supplies into a PDU or UPS.
Wall Outlet Power Cords Nema 5-15P to IEC320-C13, low voltage (6 ft/2 m) Wall Outlet Power Cords Wall Outlet Power Cords Wall Outlet Power Cords
HP NC512m Dual Port 10GbE Multifunction BL-c Adapter
NOTE: NOTE: An NC512m network adapter card is required for each server blade NOTE: NOTE:
connecting to the HP 10Gb Ethernet BL-c Switch
NOTE: A maximum of one NC512m is supported per server in a type II mezzanine NOTE: NOTE: NOTE:
slot.
NOTE: NOTE: NOTE: The NC512m requires a minimum of 4 GB of server memory and supports a NOTE:
maximum of 32 GB. Therefore, when an NC512m is installed in a blade server, the
server is limited to a maximum of 32 GB of memory.
HP 4Gb Virtual Connect Fibre Channel Module for c-Class BladeSystem
16 port FC Pass-thru Module for c-Class BladeSystem
HP Brocade 4/12 SAN Switch
HP Brocade 4/24 SAN Switch Power Pack
HP Brocade 4/24 SAN Switch
HP Brocade 4/12 SAN Switch Upgrade LTU
Cisco MDS 9124e 12 port Fabric Switch
HP 4X DDR IB Switch Module for HP c-Class BladeSystem
HP 8.6 kVA Monitored PDU, 30A
HP 8.3kVA Modular Distribution Unit 40 Amp
HP 4.9kVA Modular Distribution Unit 24 Amp
HP Two C-13 PDU Extension Bars
HP rack-mountable R5500 UPS (5000VA / 4500 watts)
NOTE: The R5500 includes four c-13 PDU Extension bars. NOTE: NOTE: NOTE:
NOTE: NOTE: NOTE: The R5500 supports 4 power supplies in the Power Supply Redundant (N+1) power mode. NOTE:
NOTE: HP Power cord (6 ft) 1.83 meter 10A C-13-UL domestic power cord, for NOTE: NOTE: NOTE:
grounded USA 110V wall outlets.
DA - 12790 North America — Version 7 — February 11, 2008
(For connection to standard wall outlets)
HP BladeSystem c3000 Enclosure HP BladeSystem c3000 Enclosure HP BladeSystem c3000 Enclosure HP BladeSystem c3000 Enclosure
440910-B21
409513-B21
403626-B21
AE370A
AE371A
AE372A
AE373A
AG641A
410398-B21
AF504A
252663-D73
252663-D72
AF500A
AF426A
AF556A
Page 16