Hide thumbs Also See for ZB 350:


ZB 350


Table of Contents

Summary of Contents for Zanussi ZB 350

  • Page 2: Service And Spare Parts

    To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department.
  • Page 3: Important Safety Information

    • If the room where the hood is to be used cause injury or more serious malfunction. contains a fuel burning appliance such as a Refer to your local Zanussi Service Force central heating boiler then its flue must be of Centre. Always insist on genuine spare the room sealed or balanced flue type.
  • Page 4: Your Appliance

    YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing.
  • Page 5 The appliance can be installed to recirculate or extract contaminated air. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. The contaminated air is cleaned by passing through the filters and then back into the kitchen.
  • Page 6: Maintenance And Cleaning

    MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent.
  • Page 7: Changing The Light Bulb

    Synthetic Paper Grease Filter The filter has saturation indicators, which are small squares made from a series of dots. When the white paper inside the squares becomes saturated with grease the coloured dots start to run and spread across the paper, indicating that the filter has reached saturation point and must be replaced.
  • Page 8: Something Not Working

    SERVICE AND SPARE PARTS If you require an engineer or wish to purchase For general assistance with your appliance or for information on Zanussi products please spare parts contact your local Service Force contact our Customer Care Department. Centre by telephoning:...
  • Page 9: Peace Of Mind For Twenty Four Months

    PEACE OF MIND FOR TWENTY FOUR MONTHS STANDARD GUARANTEE CONDITIONS We, Zanussi Ltd., undertake that if within twenty four months of the date of the purchase this ZANUSSI built-in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that.
  • Page 10: Installation Instructions

    INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS HEIGHT: 35 cm WIDTH 60 cm DEPTH: 27-36 cm DEPTH WITH VISOR OPEN: 54-63 cm WEIGHT GROSS: 11.4 kg 10.6 kg ELECTRICAL SUPPLY: Voltage (50Hz)
  • Page 11: Installing The Cooker Hood

    INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood.
  • Page 12: Fitting The Wall Brackets

    Clearance Height A minimum clearance height of 650mm ”) is required when installed above a built-in electric hob, or 700mm (27 ”) when installed above a built-in gas hob. A minimum clearance height of 685mm (27”) is required when installed above a slot-in electric cooker, or 787mm (30 ”) when installed above a slot-in gas cooker.
  • Page 13 Venting The hood is more effective when used in the extraction setting (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 100mm (4”) minimum. The ducting used must be manufactured from fire retardant material .
  • Page 14 Fitting the Cooker Hood to the Wall Fit the brackets with the round ends facing downwards using the plastic rawl plugs and screws provided. Once the brackets are secured, lift the hood squarely to the wall slightly higher than the brackets. Lower the cooker hood until it is located onto the two brackets.
  • Page 15 Failure to align the top edge of the decor panel with the template will prevent the visor from opening when installed. Before drilling, use a tape measure to check the distances of the screw holes (as given on the template). The template may have altered due to dampness after manufacture.
  • Page 16 Dir. 89/336/CEE 73/23/CEE 4324167 02 - 0998...

Table of Contents