Advertisement
General Guide
Pull out the crown to the fi rst click and then rotate it to navigate between modes. Push the crown back in
after entering the mode you want.
Pulling out the crown to the fi rst click and then holding down B for at least two seconds will return
directly to the Timekeeping Mode.
Timekeeping Mode
Stopwatch
Stopwatch Minute Hand
Second Hand
(Up to 60 minutes: fi ve
12-minute revolutions)
Hour Hand
Minute Hand
Start
Stop
Crown
Reset
Day of the Week
Day Indicator
Second Hand
World Time Minute Hand
World Time Hour Hand
E-24
Using the Stopwatch
Perform this operation in any mode.
A
A
A
Start
Stop
Resume
Note
As the 9 Day Indicator changes after you switch between the Timekeeping Mode and World Time
Mode, the 8 Mode Hand also rotates (page E-2).
The 9 Day Indicator changes gradually at midnight each day. It take anywhere from about 90 seconds
to three minutes for the day to change.
E-26
Selecting a City
Your watch lets you select from among city codes for 29 cities around the globe, plus one code for
UTC (Universal Coordinated Time). Selecting a city code causes the watch's time setting to change
automatically to indicate the current time in that zone.
Important!
You can use the same steps to select a city code in the Timekeeping mode and the World Time Mode.
In the Timekeeping Mode, the city setting is the Home City, and in the World Time Mode, it is the World
Time City.
To select a city
Note
This watch does not have a city code that corresponds to
Newfoundland.
1. Pull out the crown to the second click.
This will cause the 2 Second Hand to move to the city code of
the currently selected city.
This indicates the city code setting mode.
Leaving the crown pulled out for more than two minutes without
performing any operation will automatically cause crown
operations to become disabled. If this happens, press the
TYO (TOKYO)
crown back in, pull it out, and then start the operation over
again.
Illustration shows Timekeeping Mode.
For details about city codes, see the "City Code Table" at the
back of this manual.
E-28
STD/DST Switching
You can select summer time or standard time independently for each city. The initial default setting for all
cities is AT (AUTO).
Normally you should use the AT (AUTO) setting because it automatically switches between summer time
and standard time. You should change the setting to STD (standard time) or DST (summer time) in the
following cases.
−
When using the watch in a city not included in the City Code Table
−
When the switching dates in your location are different from those shown in the City Code Table
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time.
Remember that not all countries or even local areas use Daylight Saving Time.
Note that you cannot switch between STD (standard time) and DST (daylight saving time) while UTC*
is selected as the city code.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping. The reference point for
UTC is Greenwich, England.
E-30
Operation Guide 5347 (OC)
Pull out the crown to the fi rst click.
A button
Press once to start an
elapsed time operation.
B button
Pressing once while the
2 Second Hand is indicating
normal timekeeping will
cause the 2 Second Hand to
move to A (a.m.) or P (p.m.)
for about one second.
After last signal receive result
is indicated (page E-19), the
2 Second Hand returns to
normal timekeeping.
A
B
Stop
Reset
World Time
Minute Hand
Minute Hand
Hour Hand
World Time
Hour Hand
Points to WT.
World Time
Second Hand
World Time Day
Indicator
Stopwatch Second Hand
Stopwatch Minute Hand (Up to 60 minutes:
fi ve 12-minute revolutions)
World Time Minute Hand
World Time Hour Hand
Points to ST.
Stopwatch Second Hand
Stopwatch 1/20 (0.05) Second Hand
Hour Hand
Watch Modes
Timekeeping Mode
World Time Mode
(Crown pulled out to fi rst click.)
In upper dial
In lower dial
The day of the week is indicated in the Timekeeping Mode. Pulling out the crown to the fi rst click will
cause the Mode Hand to move to TM. The mode indicators to the left and right of the Mode Hand
indicate the upper and lower dial hand functions: ST (Stopwatch) for the upper dial and WT (World
Time) for the lower dial.
In the World Time Mode, the Mode Hand points to WT. The mode indicators to the left and right
indicate the upper and lower dial hand functions: TM (Timekeeping) for the upper dial and ST
(Stopwatch) for the lower dial.
In the Stopwatch Mode, the Mode Hand points to ST. The mode indicators to the left and right indicate
the upper and lower dial hand functions: WT (World Time) for the upper dial and TM (Timekeeping) for
the lower dial.
2. Rotate the crown to move the 2 Second Hand to the city code
you want to select.
Each time you select a city code, the 1 Hour Hand, 3 Minute
Hand, 8 Mode Hand, and 9 Day Indicator move to the current
time for that city code.
3. After the setting is way you want, push the crown back in.
The day of the week and day will also be displayed in
accordance with the selected city code.
To switch between standard time and summer time manually
1. Pull the crown out to the second click.
The 2 Second Hand will move to the currently selected city code.
Leaving the crown pulled out for more than two minutes without performing any operation will
automatically cause crown operations to become disabled. If this happens, press the crown back in,
pull it out, and then start the operation over again.
2. Press A.
The 2 Second Hand will move to the currently selected summer time setting (see table below).
After about two seconds, the 2 Second Hand will return to the city code setting.
Be sure to perform step 3 within two seconds after you press A (while the 2 Second Hand is
indicating the summer time setting).
The watch automatically switches between standard time and daylight saving time in
AT (AUTO)
accordance with its calendar.
STD
The watch always shows standard time.
DST
The watch always shows daylight saving time.
3. Hold down A for about one second to cycle through the summer time settings as shown below.
A
AT (AUTO)
4. After the setting is way you want, push the crown back in.
World Time Mode
A button
Press once to start an elapsed time
operation.
Start
Stop
B button
Pressing once while the 2 Second
Crown
Hand is indicating normal
timekeeping will cause the 2 Second
Reset
Hand to move to A (a.m.) or P (p.m.)
for about one second.
After last signal receive result is
indicated (page E-19), the 2 Second
Hand returns to normal timekeeping.
Stopwatch Mode
Start
Stop
Crown
Stopwatch Minute Hand
(0 to 60 minutes)
Reset
Minute Hand
Stopwatch Mode
In upper dial
In upper dial
In lower dial
In lower dial
A
STD
DST
A
E-25
E-27
E-29
E-31
Advertisement
