Yamaha AR230 Owner's/Operator's Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Boat
  5. AR230 High output
  6. Owner's/operator's manual

Yamaha AR230 Owner's/Operator's Manual

High output
Hide thumbs Also See for AR230:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's/operator's Manual
READ THIS MANUAL
CAREFULLY BEFORE OPERATION

Advertisement

Table of Contents
loading

Related Manuals for Yamaha AR230

Summary of Contents for Yamaha AR230

  • Page 1 READ THIS MANUAL CAREFULLY BEFORE OPERATION...
  • Page 2 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. YAMAHA LIT-CALIF-65-01...
  • Page 3 AR/SR/SX230 (SXT1100F / SXT1100A-F / SXT1100B-F / SXT1100C-F / SXT1100D-F / SXT1100E-F) OWNER’S/OPERATOR’S MANUAL © 2006 by Yamaha Motor Corporation, USA 1st Edition, September 2006 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, USA is expressly prohibited.
  • Page 5 AR230/SR230/SX230 aFety nFormation & F eatures unctions peration & c aintenance & s roubleshooting pecial rocedures onsumer nFormation...

  • Page 7: Table Of Contents

    Chapter 1 SAFETY INFORMATION IDENTIFICATION NUMBER RECORDS ......1-1 Primary I.D. Number ......... 1-1 Hull Identification Number (H.I.N.) .

  • Page 9: Identification Number Records

    NFORMATION IDENTIFICATION NUMBER RECORDS Record your Primary I.D., H.I.N., and engine numbers in the spaces provided to assist you in ordering spare parts from your Yamaha Boat dealer. Also record and keep these I.D. numbers in a separate place in case your boat is stolen. PRIMARY I.D. NUMBER The Primary I.D. number is stamped on a label 1 attached to the inside of the engine compartment.

  • Page 10: Star Labels

    AFETY NFORMATION STAR LABELS FOUR STARS - SUPER ULTRA LOW EMISSION This watercraft is labeled in California The four-star label identifies engines with a California Air Resources Board that meet the Air Resources Board’s (CARB) star label 1. See below for a Sterndrive and Inboard marine engine desciption of your particular label.

  • Page 11: Emission Control Information

    EMISSION CONTROL INFORMATION ENGINE FAMILY : THIS ENGINE CONFORMS TO U.S. EPA REGULATIONS FOR MARINE S1 ENGINES SPARK PLUG GAP (mm) : FELs g/low - hr TROLLING SPEED : YAMAHA MOTOR CO., CO, LTD. MANUFACTURED DATE LABEL 2 Manufactured date label YAMAHA Manufactured:...

  • Page 12: Important Labels

    11 12 13 14 15 16 17 18 19 20 41 42 43 44 45 46 47 48 49 50 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 18 19 20 41 42 43 44 45 46 47 48 49 50 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 21 22 23 24 25 26 27 28 29 30 51 52 53 54 55 56 57 58 59 60 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 51 52 53 54 55 56 57 58 59 60 7 28 29 30 2 3 4 5 6 7 8 9 10 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 31 32 33 34 35 36 37 38 39 40 AR230 MODEL SHOWN 26 27 28 29 30 21 22 23 24 25 26 27 28 29 30 11 12 13 14 15 16 17 18 19 20 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 20 7 38 39 40 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 41 42 43 44 45 46 47 48 49 50 36 37 38 39 40 4 15 16 17 18 19 20 31 32 33 34 35 36 37 38 39 40 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 13 14 15 16 17 18 19 20 7 48 49 50...

  • Page 13: Labels

    AFETY NFORMATION WARNING LABELS...

  • Page 14: Nformation

    AFETY NFORMATION 7 8 9 10 17 18 19 20 27 28 29 30 37 38 39 40 8 9 10 47 48 49 50 18 19 20 57 58 59 60 28 29 30 38 39 40 48 49 50 9 10 58 59 60 19 20 29 30 39 40 49 50 1 2 3 4 5 6 7 8 9 10 59 60 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 1 2 3 4 5 6 7 8 9 10 41 42 43 44 45 46 47 48 49 50 11 12 13 14 15 16 17 18 19 20 51 52 53 54 55 56 57 58 59 60 22 23 24 25 26 27 28 29 30 32 33 34 35 36 37 38 39 40 42 43 44 45 46 47 48 49 50 52 53 54 55 56 57 58 59 60...

  • Page 15: Other Labels

    1 2 3 4 5 6 7 8 9 10 41 42 43 44 45 46 47 48 49 50 41 42 43 44 45 46 47 48 49 50 11 12 13 14 15 16 17 18 19 20 2 3 4 5 6 7 8 9 10 51 52 53 54 55 56 57 58 59 60 51 52 53 54 55 56 57 58 59 60 21 22 23 24 25 26 27 28 29 30 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 31 32 33 34 35 36 37 38 39 40 22 23 24 25 26 27 28 29 30 11 12 13 14 15 16 17 18 19 20 41 42 43 44 45 46 47 48 49 50 2 33 34 35 36 37 38 39 40 21 22 23 24 25 26 27 28 29 30 3 4 5 6 7 8 9 10 51 52 53 54 55 56 57 58 59 60 AR230 MODEL ONLY 2 43 44 45 46 47 48 49 50 31 32 33 34 35 36 37 38 39 40 13 14 15 16 17 18 19 20 52 53 54 55 56 57 58 59 60 41 42 43 44 45 46 47 48 49 50 23 24 25 26 27 28 29 30 1 2 3 4 5 6 7 8 9 1 51 52 53 54 55 56 57 58 59 60 33 34 35 36 37 38 39 40 11 12 13 14 15 16 17 18 19 20 4 5 6 7 8 9 10 OTHER LABELS 43 44 45 46 47 48 49 50 21 22 23 24 25 26 27 28 29 14 15 16 17 18 19 20 53 54 55 56 57 58 59 60 31 32 33 34 35 36 37 38 39 24 25 26 27 28 29 30...

  • Page 16: Safety Information

    Basic Orientation Video. Showing them the video may help reinforce the information contained in these mate- rials. LIMITATIONS ON WHO MAY OPERATE THE BOAT l Yamaha recommends a minimum operator age of 16 years old. l Adults must supervise use by minors.

  • Page 17: Required Equipment

    (including metric stored on your boat. A mirror can sizes), and electrical tape. also be used as an emergency sig- l Oar or paddle (look for one with a nal. Contact your Yamaha dealer or boat hook on the other end). the Coast Guard for more informa- tion. l Spare parts, such as an extra set of l Sound Signalling Device: spark plugs and fuses.

  • Page 18: Cruising Limitations

    AFETY NFORMATION CRUISING LIMITATIONS risk of back/spinal injury (paraly- sis), facial injuries, and broken legs, l Scan constantly for people, objects, ankles, and other bones. Do not and other watercraft. Be alert for jump waves or wakes. conditions that limit your visibility or l Do not operate the boat in rough block your vision of others. water, bad weather, or when visibility is poor; this may lead to an accident causing injury or death. Be alert to the possibility of bad weather. Take note of weather forecasts and the prevailing weather conditions before...

  • Page 19: Care

    AFETY NFORMATION OPERATIONAL REqUIREMENTS l For reasons of safety and proper care of the boat, always perform the l All riders must wear a Coast Guard pre-operation checks listed on page approved personal flotation device 3-4 before operating. (PFD). l Passengers must always sit in a designated seating area, place feet on the deck, and hold on to the hand grips when the boat is in motion. l Eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you oper- ate your boat. Restraining straps...

  • Page 20: Hazard Information

    AFETY NFORMATION l Attach the engine shut-off cord (lan- l Maintain a safe distance from other yard) to the PFD and keep it free boats or watercraft, and also watch from the steering wheel or other for boats’ ski ropes or fishing lines. controls so that the engine stops if Obey the “Rules of the Road” (see the operator accidentally leaves the page 1-15), and be sure to check helm. Failure to attach the engine...

  • Page 21: Night Operation

    AFETY NFORMATION an open area without obstructions until you have a good feel for the JET THRUST NOzzLES maneuver. l This Yamaha Boat is water-jet pro- pelled. The pumps are directly con- nected to the engines. This means INTAKE GRATE that the jet thrust will produce some movement whenever the engines are running. The boat has a “neu- tral” position, but since the boat is...

  • Page 22: Water-Skiing

    Normal when the skier falls or is unable to swimwear does not adequately pro- get up on the skis. tect against forceful water entry into rectum or vagina. The skier should For the AR230, also see page 2-21 wear a wetsuit bottom or clothing for Wakeboard tower use. that provides equivalent protection. Such clothing includes thick, tight- ly woven, sturdy, and snug fitting...

  • Page 23: Rules Of The Road

    AFETY NFORMATION RULES OF THE ROAD Stand-On Vessel The vessel with the right-of-way has the duty to continue its course and speed, Your Yamaha Boat is legally considered except to avoid an immediate collision. a powerboat. Operation of the boat When you maintain your direction and must be in accordance with the rules speed, the other vessel will be able to and regulations governing the water- determine how best to avoid you. way on which it is used. Give-Way Vessel Just as there are rules that apply...

  • Page 24: Rules When Encountering Vessels

    AFETY NFORMATION RULES WHEN ENCOUNTERING Meeting If you are meeting another power ves- VESSELS sel head on, and are close enough There are three main situations that to run the risk of collision, neither of you may encounter with other vessels you has the right-of-way! Both of you which could lead to a collision unless should alter course to avoid an acci- the Steering Rules are followed:...

  • Page 25: Other Special Situations

    AFETY NFORMATION Narrow Channels and Bends When navigating in narrow channels, you should keep to the right when it is safe and practical to do so. If the operator of a power-driven vessel is preparing to go around a bend that may obstruct the view of other water vessels, the operator should sound a prolonged blast of four to six seconds...
  • Page 26 AFETY NFORMATION “1” “3” “5” “7” C “1” LIGHTED BUOY (Port Hand) “6” N “2” Odd number, increasing toward head “7” of navigation. Leave to port (left) pro- RB “L” ceeding White Light Green Light RG “L” “5” “4” “2” “4” “6” LIGHTED BUOY (Starboard Hand) Even number, increasing toward head “3”...

  • Page 27: Reading Buoys And Other Markers

    The Online Boating Safety Course, a particular state. The Uniform State available through the watercraft sec- Waterway Marking System has been tion of the yamaha-motor.com website, devised for these waters. is a free, 50-question learning course This system uses buoys and signs with available to the public. Upon success-...

  • Page 28: Enjoy Your Boat Responsibly

    AFETY NFORMATION ENJOY YOUR BOAT RESPONSIBLY You share the areas you enjoy when operating your boat with others and with nature. So your enjoyment includes a responsibility to treat these other peo- ple, and the lands, waters, and wildlife with respect and courtesy. Whenever and wherever you are boat- ing, think of yourself as the guest of those around you. Remember, for example, that the sound of your boat may be music to you, but it could be just noise to others. And the exciting...
  • Page 29 Chapter 2 FEATURES & FUNCTIONS LOCATION OF MAIN COMPONENTS ...... 2-1 OPERATION OF CONTROLS AND OTHER FUNCTIONS.... 2-5 Steering .

  • Page 31: Location Of Main Components

    & F EATURES UNCTIONS LOCATION OF MAIN COMPONENTS 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 21 22 23 24 25 26 27 28 29 30 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 31 32 33 34 35 36 37 38 39 40 11 12 13 14 15 16 17 1 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 21 22 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 3 31 32 33 34 35 36 37 38 39 40 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 11 12 13 14 15 16 17 18 19 11 12 13 14 15 16 17 18 19 20 41 42 43 44 45 46 47 48 49 50 21 22 23 24 25 26 27 21 22 23 24 25 26 27 28 29 30...
  • Page 32 & F EATURES UNCTIONS AR230 MODEL SHOWN...
  • Page 33 25 26 27 28 29 30 1 52 53 54 55 56 57 58 59 60 8 9 10 34 35 36 37 38 39 40 17 18 19 20 Center Walk-Through Folding Windshield 43 44 45 46 47 48 49 50 52 53 54 55 56 57 58 59 60 26 27 28 29 30 11 12 13 14 15 16 17 18 19 20 35 36 37 38 39 40 Fire Extinguisher Holder 18 19 20 44 45 46 47 48 49 50 53 54 55 56 57 58 59 60 27 28 29 30 36 37 38 39 40 Wakeboard Tower (AR230 MODELS ONLY) 21 22 23 24 25 26 27 28 29 30 45 46 47 48 49 50 54 55 56 57 58 59 60 7 28 29 30 37 38 39 40 46 47 48 49 50 55 56 57 58 59 60 31 32 33 34 35 36 37 38 39 40 7 38 39 40 LOCATION OF STEREO COMPONENTS: 47 48 49 50 56 57 58 59 60 41 42 43 44 45 46 47 48 49 50 A Remote Control Keypad (AR and SX only) 7 48 49 50 57 58 59 60 B Speakers...
  • Page 34 & F EATURES UNCTIONS LOCATION OF MAIN COMPONENTS 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 30 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 30 11 12 13 14 15 16 17 18 19 20 33 34 35 36 37 38 39 40 31 32 33 34 35 36 37 38 39 40 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 31 32 33 34 35 36 37 38 39 40 31 32 33 34 35 36 37 38 39 40 PORT STBD 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 31 32 33 34 35 36 37 38 39 40 43 44 45 46 47 48 49 50 21 22 23 24 25 26 27 28 29 30...

  • Page 35: Operation Of Controls And Other Functions

    & F EATURES UNCTIONS OPERATION OF TILT LEVER CONTROLS AND OTHER FUNCTIONS STEERING 1 2 3 4 5 6 7 8 9 PORT STBD 11 12 13 14 15 16 17 18 19 The tilt lever 1 is located under the steering wheel and is used to adjust 21 22 23 24 25 26 27 28 the tilt of the steering wheel. There are three positions. 31 32 33 34 35 36 37 38 To adjust the tilt, pull the lever up, and 1 Steering wheel 41 42 43 44 45 46 47 48 then move the steering wheel up or Your boat can be steered by turning down to the desired position. The lever...

  • Page 36: Engine Shut-Off Switch

    & F EATURES UNCTIONS WARNING ENGINE SHUT-OFF SWITCH The clip on the end of the engine l Always attach the engine shut-off shut-off cord must be attached to the cord to your personal flotation engine shut-off switch for the engines device (PFD) BEFORE starting to run. The cord must be attached to the engines.

  • Page 37: Throttle/Shift Levers

    & F EATURES UNCTIONS OFF: WARNING Ignition circuits are switched off. The Before starting the engine, check the engine cannot be started but other operation of each engine’s throttle/ switches will operate. (The key can be shift lever. It should move smoothly removed.) through the full range of operation.
  • Page 38 & F EATURES UNCTIONS l Do not shift into Reverse while Neutral The jet pump gates are dropped down traveling at planing speeds. Loss part way over the jet nozzles. Some jet of control, boat swamping, or thrust is to the rear and some jet thrust damage to the boat could occur. is redirected forward. This balance of NOTE: This boat is equipped with thrust acts like “neutral” to keep the “start-in-gear” protection. The engines boat from moving.

  • Page 39: Fuel Tank Filler Cap

    & F EATURES UNCTIONS Free Accelerator GAUGES This control is equipped with a “Free 1. Speedometer Accelerator” button which will allow The speedometer 1 shows the boat engines to be accelerated with the jet speed in miles per hour (mph). pump gates in the Neutral position. 1 2 3 4 5 6 7 8 9 WARNING The boat will start moving as if it 11 12 13 14 15 16 17 18 19 were in Forward or Reverse if engine speed is increased above idle in...
  • Page 40 & F EATURES UNCTIONS 3. Fuel Level Gauge 4. Depth Sounder (not all models) The fuel level gauge 1 shows the amount of fuel in the fuel tank. The 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 ignition switch must be in the “ON” 11 12 13 14 15 16 17 18 19 20 position to activate the gauge. 11 12 13 14 1 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 1 2 3 4 5 6 21 22 23 24 25 26 27 28 29 30 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16...
  • Page 41 & F EATURES UNCTIONS pect shallow water or submerged objects, as water depth may change too quickly to allow time for you to react. • Extremely dirty water, very soft bottom, high speeds, deep water, Setting the Shallow Alarm or a combination of the above The Shallow Alarm function can be set may result in incomplete or inac- for depths ranging from 3 to 199 feet (1...
  • Page 42 & F EATURES UNCTIONS reduce the value. Press and release 2) Press the “UP” key within 5 seconds either key to change the value in 1- to increase the selected value (more foot increments. Press and hold the water depth). Press the “DOWN” key to change the value in 9-foot key to reduce the value. Press and increments per second. release either key to change the 3) After your selection is made, the value in 1-foot increments. Press display will return to normal opera- and hold the key to change the tion after 5 seconds.

  • Page 43: Overheat Warning System

    1 on the starboard tion or a short circuit is detected, side of the hull. Check that water comes the warning indicator will come on. out of the outlet while the engine is run- If this occurs, reduce engine speed ning, particularly while applying throttle. and return to shore. Have a Yamaha If you do not see any water at the out- dealer check the engine and cir- let, cooling water may not be circulating cuits. in the engine. Engine Overheat – This model is...

  • Page 44: Switches

    & F EATURES UNCTIONS CAUTION: 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 If the cause of overheating cannot 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 PORT STBD be found and corrected, take special precautions to avoid major engine 21 22 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 30 damage while you return to shore. 31 32 33 34 35 36 37 38 39 40 31 32 33 34 35 36 37 38 39 40 31 32 33 34 35 36 37 38 39 40 SINGLE ENGINE OVERHEATING —...
  • Page 45 & F EATURES UNCTIONS Lights This toggle switch controls the required on-board lighting. Press the top of the STBD PORT switch to turn on both the bow light and stern light for night running. Press the bottom of the switch to operate the stern light alone when anchored at night. Put the switch in the middle posi- tion to turn off all lights (see page 3-9). Horn Pressing this switch activates the horn. The horn can be used to signal other boats as required by the “Rules of the Road” (see page 1-15).

  • Page 46: Swivel Seat Operation

    The electrical circuit for each switch position. There is also a friction lever 3 is protected by a circuit breaker. If the to adjust how easily the seat rotates. button below a switch pops out, push The seat must always be locked into it back in with your finger. If it pops out again, ask your Yamaha dealer to the full front-facing position before get- ting underway. inspect the electrical system. The seat bolster on AR and SX models will flip up for a raised seating position. 1 2 3 4 5 6...

  • Page 47: Passenger Seat

    & F EATURES UNCTIONS PASSENGER SEAT The passenger seat on the port side can be positioned in two ways. It can be positioned with an upright backrest in the middle, or flat as a bench seat. 1 2 3 4 5 6 7 8 9 10 To position the seat as a bench seat, lift 11 12 13 14 15 16 17 18 19 20 the latch on the underside of the seat. Hold the seat by the straps provided 21 22 23 24 25 26 27 28 29 30 and pull the front of the seat forwrd until it rests on the console lip. 31 32 33 34 35 36 37 38 39 40 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 STEREO SYSTEM 41 42 43 44 45 46 47 48 49 50 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20...

  • Page 48: Engine Hood

    & F EATURES UNCTIONS ENGINE HOOD Bow Anchor Storage There is a hood latch located under the front of the rear seat. To open the engine hood, lift the latch hook upward and lift the hood. The hood is supported by gas-filled struts. Hood Latch and Struts Under Front Seats Pull up the seat cushions to access the storage compartments. The starboard side compartment on AR and SX models is designed to be used as an ice chest. Ski Locker STORAGE COMPARTMENTS Your boat has convenient on-board storage areas.
  • Page 49 & F EATURES UNCTIONS Driver’s Side Console WARNING Do not carry any flammable sub- stances in the battery compartment or any heavy or metal items that can damage the battery or cause a short circuit. Sparks or fire could result. Enclosed Head Compartment The port-side console has a large compartment suitable for use as an...

  • Page 50: Front Walk-Through

    & F EATURES UNCTIONS Windshield There is a light in the compartment. Press the light to turn it on. Press the Unsnap the retaining strap 1 from light again to turn it off. the windshield and pivot it into place. Rotate the two latches 2 to keep the CAUTION: windshield secured. When the wind- Be sure the light is turned off when...

  • Page 51: Rear Walk-Through

    Do not climb, hang, or sit on the wakeboard tower. CAUTION: Do not modify the tower to tow from any other point or to carry any acces- sories or equipment not approved by Yamaha. The tower could be dam- aged. 2-21...
  • Page 53 Chapter 3 OPERATION FUEL AND OIL .......... 3-1 Gasoline .

  • Page 55: Operation

    Off before refueling. minimum octane ratings. Gasohol con- taining methanol is not recommended l Refuel in a well-ventilated area. If by Yamaha because it can cause fuel the boat is in the water, be sure it system damage or engine performance is securely moored to the fueling problems.

  • Page 56: Engine Oil

    Ring Free Fuel Additive, Do not “top off” the tank, because available from your Yamaha dealer. gasoline could spill out. Be sure to Ring Free has repeatedly proven its tighten the cap securely.
  • Page 57 If the level is above the “F” mark, the engine is overfilled. Consult a 2) If the level is at least at the minimum level “L” mark 2 on the dipstick, Yamaha dealer to have oil extracted from the engine to avoid damage. but less than the “F” mark 3, the engine can be operated.

  • Page 58: Pre-Operation Checks

    PERATION PRE-OPERATION WARNING CHECKS If any item in the Pre-Operation check is not working properly, have CHECK LIST it inspected and repaired before operating the boat. Otherwise an Before Operating this boat, perform the accident could occur. following checks: PAGE ITEM CHECK REF. BEFORE LAUNCH OR OPERATION: STEERING Check for proper steering operation.

  • Page 59: Check Points

    PERATION NOTE: Pre-operation checks should Throttle/Shifters be made each time the boat is used. This procedure can be accomplished thoroughly in a short time. The added safety and reliability the checks assure is worth the time involved. CHECK POINTS Steering Move the control levers several times through their full range of motion. Operation should be smooth over the complete range of motion and the levers should return to Neutral without...

  • Page 60: Operation

    USCG- approved fire extinguisher whenever Fire Extinguisher the boat is operated. A fire extinguisher is not standard equipment with this boat. If you do not have one, contact your local Yamaha Boat dealer or a fire extinguisher dealer to obtain one meeting the proper speci- fications. Access Port Caps Lift the hatch on the rear platform.

  • Page 61: Drainage System

    PERATION Jet Intakes Fuel System Refer to page 4-10, “FUEL SYSTEM INSPECTION,” for correct procedure. 1 2 3 4 5 6 7 8 9 10 Fuel and Engine Oil Levels 11 12 13 14 15 16 17 18 19 20 1) Turn the right switch key to ON. Wait for the fuel gauge needle to stop 21 22 23 24 25 26 27 28 29 30 moving, then note the fuel level. Add 1 2 3 4 5 6 7 8 9 10 31 32 33 34 35 36 37 38 39 40 fuel if necessary. NOTE: The fuel level is most accurate 11 12 13 14 15 16 17 18 19 20 41 42 43 44 45 46 47 48 49 50 when the boat is sitting level on the...
  • Page 62 PERATION water from traveling back to the deck A drain plug is located at the center of the stern to allow more complete drain- during mooring or while moving in ing when the boat is removed from the reverse. water. Bilge Pump – Engine Compartment and Fuel Compartment Drain Plug – 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 21 22 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 40 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 50 Your boat is equipped with a drainage 41 42 43 44 45 46 47 48 49 system that channels water that enters Water will not normally enter the engine...

  • Page 63: Engine Compartment

    PERATION Engine Compartment Lights 1 2 3 4 5 6 7 11 12 13 14 15 16 17 21 22 23 24 25 26 27 31 32 33 34 35 36 37 41 42 43 44 45 46 47 51 52 53 54 55 56 57 Check for proper operation of the bow, Operate the bilge blower switch 1 for stern, and instrument lights by pressing at least 4 minutes before starting the the switch 3 on the control panel. engines. Open engine hood and check to be sure no gasoline vapors are present. Check for fuel leaks or loose electrical connections.
  • Page 64 PERATION Horn Cooling-Water Pilot Outlets Check that water comes out from the Press the horn switch 1 to be sure the pilot outlets while engine is running in horn operates. the water. Refer to page 2-13 for cor- 1 2 3 4 5 6 7 8 9 10 rect operation of the device. 11 12 13 14 15 16 17 18 19 20 PORT STBD 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Engine Shut-Off Switch NOTE: It may take up to 20 seconds for water to reach the pilot outlets when first launching the boat. The amount...
  • Page 65 Do not exceed 45 mph (72 km/h) with 3) Unfold the top by pulling to the bow the Bimini top in the up position. of the boat. NOTE: SX230 model shown. On the AR230 model, collapse the front sup- port poles to clear the wakeboard tower as you pull the top forward. Extend the poles again until the bottom sections lock into their fully extended position. 3-11...
  • Page 66 Trailering with the Bimini Top In The Upright Position The Bimini top must be secured to 1) Raise the rear support poles. the boat when it is being trailered. When trailered with a Genuine Yamaha 2) Unhook the front straps and pull the Cover, simply store the Bimini top in top to the back. the fully collapsed position and install 3) Roll the fabric around the frames the cover. If a cover is not used, wrap...

  • Page 67: Starting The Engines

    THE FOLLOWING: l Before operating your boat, become familiar with all controls. Consult your Yamaha dealer 1) Always make sure the boat is about any control or function you launched and used in waters that do not fully understand. are free from weeds and debris, and l Attach the engine shut-off switch at least 3 ft. (90 cm) deep.
  • Page 68 PERATION 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 NOTE: Before the first start-up, remove the fuel tank filler cap to release any Engine shut-off switch 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 11 12 13 14 15 16 1 built-up pressure in the tank because 1 2 3 4 5 6 7 8 9 10 Clip with cord of fuel expansion. 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 21 22 23 24 25 26 NOTE: It is not possible to start the 11 12 13 14 15 16 17 18 19 20 engine with the clip removed from the 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 31 32 33 34 35 36...

  • Page 69: Stopping The Engines

    PERATION STOPPING THE ENGINES CAUTION: Never turn the ignition key to “Start” while the engine is running. Do not keep the starter motor running for more than 5 seconds. If the engine does not start after 5 seconds of cranking, release the starter button. Wait at least 15 seconds before try- ing to start the engine again.

  • Page 70: Break-In Procedure

    PERATION BREAK-IN PROCEDURE The engine break-in period is essential to allow the various components of the engine to wear and polish themselves to the correct operating clearances. This ensures proper performance and promotes longer component life. 1) Launch the boat and start the engine (see page 3-13). 2) For the first 5 minutes, run the engine at trolling speed. For the 30 minutes of operation after that, keep the engine speed below 5,000 rpm. For the hour of operation after that, keep the engine speed below 8,000 rpm. 3) Proceed with normal operation. 3-16...

  • Page 71: Driving Your Boat

    PERATION DRIVING YOUR BOAT Know and follow U.S. Coast Guard, state, and local laws when operating your boat. GETTING TO KNOW YOUR BOAT Select a wide area to learn in, where Operating your boat requires skills visibility is good and other boat traffic acquired through practice over a period is light. Keep the proper distance from of time. Take the time to learn the basic...

  • Page 72: Turning The Boat

    PERATION TURNING THE BOAT D. If the engines are stopped, there is no thrust. The boat will go straight Steering control depends on the com- even though the steering wheel is bination of steering wheel position and turned. the amount of throttle. YOU NEED THROTTLE TO STEER. Water sucked in through the intake grate is pressurized by the impeller in the jet pump. As the pressurized water is expelled from the pump through the jet thrust nozzle, it creates thrust to...

  • Page 73: Boating With Passengers

    PERATION BOATING WITH PASSENGERS TURNING LEFT Your boat is designed for one operator and up to nine passengers only. Never have more than ten people in the boat. Passengers must sit in one of the seats and hold onto the grips. Passengers PORT STBD should sit so the weight in the boat is balanced from side-to-side and bow-to- stern as much as possible. If the pas- senger seat in front of the helm is used, be sure the operator’s view ahead is not obstructed.

  • Page 74: Boarding From A Dock Or Landing Jetty

    PERATION WARNING Stay away from the swim step while the engines are running. Exhaust gases coming from underneath it contain carbon monoxide, a col- orless, odorless gas which may cause brain damage or death when inhaled. Symptoms include nausea, dizziness, and drowsiness. 2) Climb up onto the swim platform, then sit in one of the seats provid- BOARDING FROM A DOCK OR...

  • Page 75: Stopping

    PERATION STOPPING 2) Notice how wind and water currents are affecting boat movement as you attach your mooring lines and fend- ers. 3) Approach the dock at idle speed. 346 ft (105.5 m) 345 ft (105 m) Use reverse as necessary during slow speed maneuvering to help control speed and direction. Position the boat according to wind and...

  • Page 76: Leaving A Dock

    PERATION Wind or current pushing boat toward 2) When the stern is out a few feet, dock: release the bow mooring then steer in the direction you want the bow to move. Open the throttle slightly and WIND OR CURRENT begin to move away from the dock. BEACHING 1) Make sure no obstructions, boats or swimmers are near the beach. 2) Approach the beach slowly and stop the engines when the water is about 3 ft. (90 cm) deep. Remember: turn- ing is impossible with the engine Slowly maneuver to a shallow angle stopped.

  • Page 77: Anchoring

    PERATION ANCHORING 4) Pull on the line to be sure the anchor is holding. Also, periodically WARNING check your boat’s position against the shoreline to make sure it is not Always anchor from bow. drifting and dragging the anchor. Anchoring from the stern will make Reset if necessary. the boat unsteady. A strong cur- 5) To pull in (“weigh”) the anchor, start rent can pull a stern-anchored boat the engines and move forward,...

  • Page 78: Crossing Wakes And Swells

    PERATION CROSSING WAKES AND SWELLS You will not always have flat, smooth water. There will be swells and wakes from other boats, etc. SHARP WAKES The best way to cross wakes and swells is with the least jolt to you and the boat. Small swells are not as difficult to cross as larger swells or wakes. Crossing a sharp wake gives more of a jolt than a BROAD SWELL broad swell. To cross a wake or swell, change your WAKE speed and choose the angle at which you cross the wake or swell. Usually, a slower speed and “quartering” the wake (crossing at an angle) will reduce...

  • Page 79: Post-Operation Checks

    PERATION POST-OPERATION 1) After putting the boat on the trailer, flush cooling system on each engine CHECKS to prevent the cooling system from clogging up with salt, sand, or dirt. POST-OPERATION CHECKS Refer to page 4-1 for the cooling system flushing procedure. These post-operation procedures are developed to help preserve the long- 2) Drain residual water from the exhaust term appearance and reliability of your system by starting the engine, then boat. Perform these procedures as...
  • Page 80 Clean any foreign material, such as 41 42 43 44 45 46 47 48 49 dirt or sand, from the threads before 21 22 23 24 25 26 27 28 29 30 51 52 53 54 55 56 57 58 59 installing the drain plug. 31 32 33 34 35 36 37 38 39 40 6) Spray a rust inhibitor, such as 41 42 43 44 45 46 47 48 49 50 1 2 3 4 5 6 7 8 9 10 Yamaha Silicone Protectant and 51 52 53 54 55 56 57 58 59 60 Lubricant, on metallic parts to mini- 11 12 13 14 15 16 17 18 19 20 mize corrosion. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 3-26...

  • Page 81: Trailering

    PERATION TRAILERING HITCH The trailer hitch ball must match the size of the socket on the trailer hitch WARNING coupler. Hitches are divided into class- es that specify the gross trailer weight Avoid accident and injury from (GTW) and the maximum tongue improper trailering: weight. Always use a hitch rated for the l The trailer must be matched for same or higher class. Use a bolted-on the boat’s weight and hull.

  • Page 82: Backing Your Trailer

    PERATION l Check wheel bearings and wheel ger trips, it is a good idea to carry a lug nuts before each trip. set of spare wheel bearings, seals, and races. l Check tail, brake, and turn signal lights for proper operation. l When making a turn, do not cut cor- ners. The trailer has a smaller turn- l Secure the bow of the boat to the ing circle so it turns more sharply trailer with the winch line and also around the corner than the towing with the chain. Secure the stern vehicle.

  • Page 83: Launching

    PERATION LAUNCHING 5) Remove the bow line from the bow eye. 6) Back the trailer farther into the water until just the tops of the fenders show, then reset the parking brake. Board the boat and start it. If pos- sible, remain on the trailer until the engines are warm and are respond- ing to throttle. 7) Back the boat out into the water, watching carefully for people, other As a courtesy to other boaters, prepare boats, or obstacles.

  • Page 84: Lifting

    PERATION LIFTING 4) Make sure the boat is centered on the support rails and is headed CAUTION: straight for the bow stop (bumper board). Ease the boat forward until Do not attach lifting cables to the the bow rests against the bow stop. bow eye, cleats, water-ski tow eye, or grab handles.

  • Page 85: Maintenance And Care

    SX230/AR230 ......... . . 4-19 SX230 HO / AR230 HO ........ 4-20...

  • Page 87: Storage

    Cap 51 52 53 54 55 Top off the fuel tank with fresh fuel, 51 52 53 54 55 56 57 58 59 Cooling system flushing is essential to adding one ounce of Yamaha Fuel prevent the cooling system from clog- Conditioner and Stabilizer or an equiv- ging up with salt, sand, or dirt. alent to each gallon of fuel. A full fuel tank is less likely to allow condensa-...

  • Page 88: Lubrication

    7) Repeat the flushing procedure for the other engine. LUBRICATION WARNING 4) Spray a rust inhibitor such as Yamaha Store-Rite Fogging Oil into Do not spray flammable rust inhibi- each intake opening 3 for 3 sec- tor on engine surfaces while the onds. engines are hot. The sprayed sub-...

  • Page 89: Battery

    & C AINTENANCE 7) Grease the areas of the boat 2) If the battery will be stored for a specified in “Grease Points” in the longer period, check the specific Adjustment and Maintenance sec- gravity of the fluid at least once a tion.

  • Page 90: Cleaning

    Reinstall the drain plugs. 4) Spray the exterior of the engines with Yamaha Silicone Protectant and Lubricant or an equivalent. 5) Wax the hull with a non-abrasive wax such as Yamaha Ultra Gloss Cleaner Wax or other wax designed for marine gelcoat. WARNING WARNING Slippery surfaces can cause falls and injury.

  • Page 91: Adjustment And Maintenance

    If the owner is not familiar with machine servicing, this work should be done by a Yamaha dealer or other qualified mechan- ic. Improperly serviced compo- nents could fail or stop operating correctly, which could result in an accident.

  • Page 92: Periodic Inspection Chart

    & C AINTENANCE PERIODIC INSPECTION CHART Frequency of maintenance operations may be adjusted according to the operating conditions, but the following table gives general guidelines. ● Indicates the checkups which you may do yourself. ■ Indicates work to be done by your Yamaha dealer. Maintenance interval Initial Thereafter Page Every 100 100 hours hours hours hours hours months months months months Spark plug Inspection/Cleaning/ ● ● ● ● 4-7 Adjustment ● ● Grease points Greasing ■...

  • Page 93: Spark Plug Cleaning And Adjustment

    Do not attempt to diagnose any prob- the spark plug cap down until it clicks. lems yourself. Instead, take the boat to a Yamaha Boat dealer. You should periodically remove and inspect the NOTE: If a torque-wrench is not avail- spark plug because heat and depos-...

  • Page 94: Grease Points

    & C AINTENANCE GREASE POINTS To keep moving parts sliding or rotating smoothly, coat them with water resis- tant grease such as Yamaha Marine Grease, Yamaha Grease A, or an equiv- alent. Throttle Cable Grease the throttle-cable inner wires at the carburetors. Steering Cable Ball Joints and Inner Wire Grease the steering cable and shift cables ball joints at the steering noz- zles. Extend the steering cable and...

  • Page 95: Bearing Housing

    Grease the bearing housing through the grease nipple. Recommended water-resistant grease: Yamaha Marine Grease, or Yamaha Grease A The first service should be done after 10 hours or 1 month by your Yamaha dealer. Fill the bearing housing with water- resistant grease through the grease 1 2 3 4 5 6 7 8 9 10 nipple. Grease capacity: 33.0~35.0 cc 11 12 13 14 15 16 17 18 19 20 (1.11~1.18 oz)

  • Page 96: Fuel System Inspection

    Check the fuel system for leaks, cracks, Lift the latch to open the hatch. The or malfunctions. If any problem is found, other access point is inside 2 the port- consult a Yamaha dealer. side storage compartment. Remove the seat cushion then look up inside Checking points: the compartment to see the fuel filler 1. Fuel tank leakage...

  • Page 97: Fuel Tank

    Coming into engine is running, immediately turn contact with or getting any engine the engine off and have a Yamaha oil on your clothes could result in dealer check the boat. Continuing burns.

  • Page 98: Air Filter

    & C AINTENANCE AIR FILTER The air filter element should be checked every 12 months or every 100 hours of operation. To check the air filter: 1) Open the hood (see page 2-17). 2) Remove the air filter case cover screws 1, slide the locks 2 to open, and then remove the case cover. 3) Remove the air filter element. Check it for dirt and oil. Replace the air filter every 2 years or every 200 hours of operation, or if it becomes contaminated with dirt or oil.

  • Page 99: Steering Cable Inspection

    & C AINTENANCE STEERING CABLE INSPECTION Be sure to check: 1) Check for smooth operation of the wheel and steering nozzles. 2) Check for proper steering adjust- ment. The nozzles should both point straight back when the steering wheel is centered. If steering is stiff or misadjusted, ask your Yamaha dealer to service it. 4-13...

  • Page 100: Controls (Throttle/Shift)

    If the controls do not operate smooth- ly or correctly, ask your authorized Yamaha Boat dealer for service. 4) Pull the shift lever back from Forward through Neutral to Reverse. The observer should check for proper movement of the shift gates. Both gates should drop down over the nozzles to the stops.

  • Page 101: Sacrificial Anodes

    2) Clean the mounting-bolts threads, then coat them with Loctite 242, ® available from your Yamaha dealer. 3) Install the new anode. Tighten the mounting bolts to specification. Anode Bolt Torque: 50~80 kgf-cm (47~70 inch-pounds) 1 ANODE Inspect the anodes each time the boat is removed from the water. It is normal for them to look corroded and rough.

  • Page 102: Fuse Replacement

    & C AINTENANCE FUSE REPLACEMENT WARNING Do not use fuses of higher amper- that those recommended. Substitution of a fuse of improper rating can cause extensive electrical system damage and possible fire. BATTERY The fuse is in the ignition coil holder. To replace the fuse, unscrew the cap NOTE: These general guidelines apply and pull the two red leads out with the...
  • Page 103 & C AINTENANCE WARNING Recharging WARNING Battery electrolyte is poisonous and dangerous, causing severe burns, ● When charging the battery, keep etc. It contains sulfuric acid. Avoid it well away from sparks and contact with skin, eyes or clothing. open flames, as it gives off explo- sive gases.
  • Page 104 & C AINTENANCE ➀ Positive (+) Battery cable (Red) ➁ Negative (–) Battery cable (Black) ➂ Accessory (+) Lead (Red/Black) 4 Accessory (–) Lead (Black) 5 Battery Switch CAUTION: BATTERY REMOVAL: Disconnect battery leads before removing the battery. Disconnect the negative (–) lead first. BATTERY INSTALLATION: Connect the red (+) lead and accessory red (+) lead to the positive (+) terminal of the battery.

  • Page 105: Specifications

    & C AINTENANCE SPECIFICATIONS ITEM / MODEL UNIT SR230 HO: SXT1100-F / SX230 HO: SXT1100A-F/B-F VEHICLE CAPACITY Maximum people on board Number of people Maximum load capacity 1800 DIMENSIONS Length feet / inches 23' / 276" Beam feet / inches 8.5' /102" Draft inches 18" Dry weight 3172 Height on trailer feet / inches 6.92' / 83" PERFORMANCE Maximum output HP (kW) / rpm 160 (117) @ 10,000 each engine Maximum fuel consumption US gal/h (L / h) 11.9 gal (45) each engine...
  • Page 106 & C AINTENANCE SPECIFICATIONS ITEM / MODEL UNIT AR230 HO: SXT1100C-F/D-F VEHICLE CAPACITY Maximum people on board Number of people Maximum load capacity 1800 DIMENSIONS Length feet / inches 23' / 276" Beam feet / inches 8.5' /102" Draft inches 18" Dry weight 3272 Height on trailer feet AR: 10.3' PERFORMANCE Maximum output HP (kW) / rpm 160 (117) @ 10,000 each engine Maximum fuel consumption US gal/h (L / h) 11.9 gal (45) each engine Cruising range (full throttle)
  • Page 107 Chapter 5 TROUBLESHOOTING & SPECIAL PROCEDURES TROUBLESHOOTING ......... . 5-1 Troubleshooting Chart .

  • Page 109: Troubleshooting

    & S ROUBLESHOOTING PECIAL ROCEDURES TROUBLESHOOTING If any trouble happens on your boat, use this section to check for possible cause. If you can- not find the cause or if the procedure for replacement or repair is not described in this owner’s manual, ask your Yamaha Boat dealer or qualified mechanic for the proper service. The Troubleshooting Chart contains: “TROUBLE,” “POSSIBLE CAUSE,” “REMEDY,” and “REFER PAGE.” Check the possible cause and remedy, and also the referred page for the maintenance steps to solve the trouble. TROUBLESHOOTING CHART TROUBLE POSSIBLE CAUSE REMEDY Page • Starter motor • Fuse Burned out • Replace the fuse and 4-16 does not turn check wiring over Run down • Recharge 4-17 • Battery Poor terminal 4-17 • Tighten as required connections Battery switch off • Turn on switch...
  • Page 110 POSSIBLE CAUSE REMEDY Page Empty • Refill as soon as possible Engine runs irregularly or Stale or • Have serviced at stalls • Fuel contaminated Yamaha dealer • Fuel filter Water or dust • Have serviced at collected Yamaha dealer Fouled or defective • Replace • Spark plug Incorrect heat range • Replace Gap incorrect • Adjust Loose • Fit properly Loose electrical • Tighten or connect properly 4-7 • Spark plug cap connections Cracked, torn or • Replace damaged Engine won’t run Jet intake clogged • Clean...

  • Page 111: Special Procedures

    & S ROUBLESHOOTING PECIAL ROCEDURES EMERGENCY WARNING PROCEDURES The operator of the towing boat must keep speed to a minimum and avoid traffic or obstacles which could be a TOWING THE BOAT hazard to the driver on the boat. RUNNING ON ONE ENGINE If one engine becomes inoperative, the properly running engine can be used to return to shore. Operate at a “no wake”...

  • Page 112: Jump Starting

    & S ROUBLESHOOTING PECIAL ROCEDURES JUMP STARTING 2) Connect one end of the negative (–) jumper cable to the negative (–) terminal of the booster battery. 3) Connect the other end of the nega- tive (–) cable to an engine hanger on either side of the engine oil tank. ENGINE HANGER 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20 ➀ Negative (–) jumper cable 21 22 23 24 25 26 27 28 29 30 21 22 23 24 25 26 27 28 29 30...

  • Page 113: Jet Pump Clean-Out Procedure

    4) Remove any weeds or debris from the drive shaft, impeller, pump hous- 1) Turn off and remove ignition keys, ing, and steering nozzle. If you can- remove lanyard, and wait for all not remove the debris, consult your movement to stop. Yamaha Boat Dealer. 2) Lift the hatch on the rear platform. 5) To reinstall the access port cap, first clean off any sand or other foreign matter from the cap or port surfaces. Insert the cap so that its slot faces the bow and lines up with the projec-...
  • Page 114 & S ROUBLESHOOTING PECIAL ROCEDURES CAUTION: 6) Press the T-handle down firmly to ● Be sure the caps are locked lock the cap in place. Pull up force- securely in place. Otherwise the fully on the handle to be sure it is cap could be forced out of the locked. If a strong pull will move access ports by water pressure, the handle, it is not locked securely...
  • Page 115 LIMITED WARRANTY ......... . 6-1 YAMAHA EXTENDED SERVICE (Y.E.S.) ...... 6-4 BOATING TERMS .
  • Page 117 OBTAINING REPAIRS UNDER WARRANTY: During the period of warranty, any authorized Yamaha Boat dealer will, free of charge, repair or replace, at Yamaha’s option, any parts adjudged defective by Yamaha due to faulty workmanship or material from the factory. All parts replaced under warranty will become the property of Yamaha Motor Corporation, U.S.A. CUSTOMER’S RESPONSIBILITY: Under the terms of this warranty, the customer will be respon- sible for ensuring that the boat is properly operated, maintained, and stored as specified in the applicable Owner’s Manual.
  • Page 118 YAMAHA MOTOR CORPORATION, USA MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, USA AND EXCLUDED FROM THIS WARRANTY.
  • Page 119 Q. Is the warranty transferable to second owners? A. Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by an authorized Yamaha Boat dealer for the policy to remain effective. CUSTOMER SERVICE If your boat requires warranty service, you must take it to any authorized Yamaha Boat dealer within the United States. Be sure to bring your warranty registration card or other valid proof of...
  • Page 120 You don’t have to pay anything for covered repairs. There’s no deductible to pay, and If visiting your dealer isn’t convenient, contact repairs aren’t “prorated.” You don’t have Yamaha with your Primary ID number or Hull any “out-of-pocket” expenses for covered Identification Number. We’ll be happy to help repairs.
  • Page 121 & I ONSUMER NFORMATION NDEX BOATING TERMS TERM DEFINITION The front part of the boat. Deck The “floor” or upper structure which covers the hull. Give-Way The vessel which must yield the right-of-way when two boats meet. Gunwale The meeting junction of the deck and hull; the upper edge around the boat. Pronounced “gun’l.” Hatch An opening in the deck which provides access below. Helm The steering console. Hull The basic part of the boat; the under side. Lanyard The cord or tether that connects the operator to the engine stop switch so the engines will stop if the operator accidentally leaves the helm. A Personal Flotation Device, also known as “life jacket.” Planing Traveling at a speed fast enough so the boat has leveled out and is skimming on top of the water. There is a wake. Port The left side of the boat. Stand-On The vessel with the right-of-way when two boats meet. Starboard The right side of the boat. Stern The back part of the boat. Sub-Planing Traveling at a medium speed. The bow of the boat is out of the water, but you are still traveling through the water. There is a wake.

  • Page 122: Float Plan

    & I ONSUMER NFORMATION NDEX SAMPLE FLOAT PLAN Leave a float plan with a responsible person on shore before boating. The example below can be copied and used. FLOAT PLAN VESSEL INFORMATION BOAT MAKE: Yamaha MOTOR TYPE: Jet MODEL: LENGTH: REGISTRATION NO: DECK COLOR: HULL COLOR: PASSENGER OPERATOR EMERGENCY PHONE: ADDRESS: PASSENGER #1: EMERGENCY PHONE: ADDRESS: PASSENGER #2: EMERGENCY PHONE: ADDRESS: PASSENGER #3: EMERGENCY PHONE: ADDRESS: PASSENGER #4: EMERGENCY PHONE: ADDRESS: DEPARTURE INFORMATION...
  • Page 123 & I ONSUMER NFORMATION NDEX Jet intake . . . . . . . . . . . 3-7, 5-5 Pre-operation checks . . . . . . . 3-4 Access Port Caps . . . . . . . . 3-6, 5-5 Post-operation checks . . . . . . 3-25 Adjustment and Maintenance . . . . 4-5 Steering.
  • Page 124 & I ONSUMER NFORMATION NDEX Filter, air . . . . . . . . . . . . . . . 4-12 Jet pump cover. . . . . . . . . . . . 5-5 Fire extinguisher . . . . . . . . . . . 3-6 Jumps . . . . . . . . . . . . . . . .
  • Page 125 Steering . . . . . . . . . . 2-5, 3-5, 3-18 Y, z Steering and sailing rules and Yamaha Extended Service (Y.E.S.) . 6-4 sound signals . . . . . . . . . . . 1-15 Steering cable ball joints and inner wire . . . . . . . . . . . . . 4-8 Steering inspection.
  • Page 126 LIT-18626-07-18...

This manual is also suitable for:

Sr230Sx230Sxt1100fSxt1100a-fSxt1100b-fSxt1100c-f ... Show all

Table of Contents