Table of Contents
Advertisement
Technical Data
Heating element ratings
Top heating element
Bottom heating element
Conventional cooking function (top+bottom)
Grill heating element
Full Grill Function (grill+top)
Convection heating element
Thermal Grill Function
Pizza Oven Function
Oven Lamp
Cooling fan
Oven fan
Total maximum rating
Voltage tension (50Hz)
Oven cavity dimensions
Height
Width
Depth
Oven cavity volume
Instructions for the installer
The instructions given below are designed
specifically for a qualified installer and should aid
him or her to perform all installation, adjustment,
and maintenance operations with absolute
precision and in compliance with all current
legislation and regulations. We strongly
recommend that all operations for the installation
of your cooker be carryed out by Qualified
Personnel in accordance with existing rules and
regulations.
Electrical connection
Before the appliance is connected:
1. Check that the main fuse and the domestic installation
can support the load;
2. Check that the power supply is properly earthed in
compliance with the current rules;
3. Check the double pole switch used for the electrical
connection can be easily reached with the appliance
built in the forniture unit.
This appliance is delivered without an electric supply
cable. A suitable cable and a proper plug, according to
the total electric load shown on the rating plate, must
be installed onto the appliance. The plug is to be inserted
into a suitable wall socket.
In case of a direct connection to the mains, it is
necessary that you install a double pole switch between
the appliance and the electricity supply, with a minimum
800 W
1000 W
1800 W
1650 W
2450 W
2000 W
1680 W
3000 W
25 W
25 W
25 W
3100 W
230 V / 400 V 3N
335 mm
395 mm
400 mm
53 l
Oven recess dimensions
Height
Width
Depth
This appliance can only be connected to the
following cast iron or ceramic hobs:
Cast iron hotplate hobs
Type: ZMF 2105 Maximum power absorbed
Power supply voltage (50 Hz) 230 V
Type: ZMFW 2305Maximum power absorbed 7,0 kW
Power supply voltage (50 Hz) 230 V
Type: ZME 2005 Maximum power absorbed
Power supply voltage (50 Hz) 230 V
Ceramic hobs
Type: ZC6675
Maximum power absorbed
Power supply voltage (50 Hz) 230 V
Type: ZK630L
Maximum power absorbed
Power supply voltage (50 Hz) 230 V
Nominal heating power
Oven with cast iron hob
Oven with ceramic hob
gap of 3 mm between the switch contacts and of a type
suitable for the required load in compliance with the
current rules. The yellow-green earth wire must not be
interrupted in any point and should be about 2 cm longer
than the neutral and phase wires.
The connection cable has to be placed in order that, in
each part, it cannot reach a temperature 50 °C higher
than the room temperature.
After the connection is carried out, test the heating
elements for about 3 minutes.
Should the supply cable need to be replaced, use the
following cable types only:
H07 RN-F; H05 RN-F; H05 RR-F; H05 VV-F;
H05 V2V2-F (T90); H05 BB-F.
The yellow-green earth wire should be about 2 cm longer
than the neutral and phase wires.
Electrical connection with the
hob
This oven can be connected to hobs indicated in the
paragraph "Technical data". The socket for connecting
the hob is located at the top of the oven cabinet. The
hobs come complete with connecting leads for the hot
plates/heat areas and ground cable; these leads feature
plug-in connectors. Connection of the hob to the oven is
carried out by plugging-in these connectors to the cor-
responding oven socket.
The plug-to-socket connection design is such as to
prevent possible wrong plugging-ins.
593 mm
560 mm
550 mm
7,0 kW
7,0 kW
5,8 kW
7,6 kW
10,1 kW
8,9 - 10,7 kW
21
Advertisement
Table of Contents
