Dvc To Hdd / Dvd Dubbing; Information On Dubbing - Toshiba RD100KB Owner's Manual

E2TE0BD_EN.book Page 40 Friday, March 5, 2010 4:49 PM

DVC to HDD / DVD Dubbing

Video
HDD HDD HDD
DVD-RW DVD-RW DVD-RW DVD-RW DVD-RW DVD-RW
DVD+RW DVD+RW DVD+RW DVD+R DVD+R DVD+R
Before recording from DVC, see page 19 for connection
instructions.
Preparing for DV dubbing (DVC to HDD):
• Make sure your DVC is in video mode.
Preparing for DV dubbing (DVC to DVD):
• Insert a recordable DVD.
• Make sure your DVC is in video mode.
If you want to record to the HDD, press [HDD] first.
If you want to record to a disc, press [DVD] first.
1
Press [INPUT SELECT
the external input channel, then press
[PROG. ] repeatedly to select DV(AV4).
2
Press [REC MODE] to select a recording mode.
(See page 28.)
3
Press [DISPLAY].
4
With "Control" highlighted, press [ENTER OK]
to display the available devices to control with
the remote control of this unit. Select "DVC"
using [K L], then press [ENTER OK].
e.g.) DVC to DVD dubbing
T 1/ 1 C 1/ 1
Control DVD
DV Audio Stereo1
Start Rec
Now you can operate your DVC with the remote control of
this unit.
5
Press [PLAY B] to start playing back the DVC,
and find where you want to start dubbing.
Press [STOP C] when it comes to the desired
start point.
6
Select "Start Rec" using [K L], then press
[ENTER OK].
The dubbing will start.
40
EN
VR
DVD-R DVD-R DVD-R
] repeatedly to select
DV
AB-1234
0:00:00
-RW VR ORG
DV
AB-1234
0:00:00
DVD SP 2:00
To stop dubbing:
1) Select "Control" using [K L], then press
[ENTER OK].
2) Select "HDD" / "DVD" using [K L] (whichever the
recording component you are using), then press
[ENTER OK].
3) Press [STOP C].
Note
• The tape will rewind a few seconds when you press
6
[ENTER OK] at step so that the dubbing starts exactly
where you press [PAUSE F] instead of [STOP C] at step
• The unit does not send out the output signal to DVC.
• For the proper operation, connect DVC to the unit directly.
Do not connect this unit and DVC via any other unit.
• Do not connect more than one DVC.
• The unit can only accept DVC. Other DV device such as
cable/satellite box or D-VHS recorder cannot be recognised.
• If no video signal is detected from the DVC during DVC to
HDD or DVD dubbing, the recording will be paused and "I"
will flash on the TV screen. The recording will resume when
the unit detects the video signal again.
• When the DVC is in camera mode, refer to "Guide to DV and
On-Screen Display" on page 39.
• Date / time and cassette memory data will not be recorded.
• Pictures with a copy-guard signal cannot be recorded.
• A DV terminal is a terminal that can use the transmission
mode conforming to the IEEE 1394 standards called
"Fire Wire". It serves as the interface that connects the PC
and peripheral device such as "i.LINK" (registered trademark
of SONY). It enables digital dubbing between DV devices
with little degradation.
• You cannot dub from DVC to both HDD and DVD at the
same time.

Information on Dubbing

You can dub the contents of the HDD to DVD or vice versa.
Before you start dubbing, refer to page 28 to see the recording
compatibility.
Difference between "Copy" and "Move":
Copy : After dubbing the programme, the original
programme will remain.
Move: After dubbing the programme, the original
programme will not remain.
Available dubbing direction for copy-once programme:
From
DVD-RW (VR)
(CPRM-compatible)
DVD-RW (VR)
HDD (Internal)
(Not CPRM-compatible)
DVD-RW (video)
DVD-R / +RW / +R
DVD-RW (VR) HDD (Internal)
V: Available
[: Not available
* The recorded programme moves. (It will be deleted from
HDD.)
You cannot dub the recorded programme to HDD or
DVD-RW again. (Refer to page 28 for details about CPRM.)
5
.
To
V*
[
[
[
[