Adjusting The Pc Image; Adjusting The Pc Image Manually; Fine Sync; Auto Sync - Sharp AQUOS LC-40LE924E Operation Manual

Connecting a PC

Adjusting the PC image

automatically
Option

Auto sync.

This function enables the screen to be automatically
adjusted to its best possible condition when the analogue
terminals of the TV and PC are connected with a
commercially available DVI/RGB conversion cable, etc.
1
Press b to select "EXT 3" from the "INPUT"
menu, and then press ;.
2
Go to "Menu" > "Setup" > "Option" >
"Terminal setting" > "Input select" > select
"RGB".
3
Go to "Menu" > "Setup" > "Option" >
"Terminal setting" > "PC input" > "Auto sync.".
NOTE
• When "Auto sync." is successful, "Auto Sync completed
successfully" displays. If not, "Auto sync." failed.
• "Auto sync." may fail even if "Auto Sync completed
successfully" displays.
• "Auto sync." may fail if the PC image has low resolution, has
unclear (black) edges, or is moved while executing "Auto
sync.".
• Be sure to connect the PC to the TV and switch it on before
starting "Auto sync.".
• "Auto sync." can be executed only when inputting analogue
signals through the EXT 3 terminal.

PC compatibility chart

Resolution
VGA 640 x 480
SVGA 800 x 600
XGA 1,024 x 768
WXGA 1,360 x 768
SXGA 1,280 x 1,024
SXGA+ 1,400 x 1,050
UXGA 1,600 x 1,200
1080p 1,920 x 1,080
VGA, SVGA, XGA, WXGA, SXGA, SXGA+ and UXGA
are registered trademarks of International Business
Machines Corporation.
Ordinarily you can easily adjust the picture as necessary
to change image position using "Auto sync.". In some
cases, however, manual adjustment is needed to
optimise the image.
1
2
3
4
5
H-Pos.
V-Pos.
Clock
Phase
NOTE
• For resetting all adjustment items to the factory preset values,
• "Clock" and "Phase" in the "Fine sync." menu can be adjusted
Horizontal Vertical
frequency frequency
31.5 kHz 60 Hz
37.9 kHz 60 Hz
48.4 kHz 60 Hz
47.7 kHz 60 Hz
64.0 kHz 60 Hz
65.3 kHz 60 Hz
75.0 kHz 60 Hz
67.5 kHz 60 Hz
NOTE
• This TV has only limited PC compatibility, correct operation can

Adjusting the PC image manually

Option

Fine sync.

Press b to select "EXT 3" from the "INPUT"
menu, and then press ;.
Go to "Menu" > "Setup" > "Option" >
"Terminal setting" > "Input select" > select
"RGB".
Go to "Menu" > "Setup" > "Option" >
"Terminal setting" > "PC input" > "Fine sync.".
Press a/b to select the specific adjustment
item.
Press c/d to adjust the item to the desired
position.
Centres the image by moving it to the
left or right.
Centres the image by moving it up or
down.
Adjusts when the image flickers with
vertical stripes.
Adjusts when characters have low
contrast or when the image flickers.
press a/b to select "Reset", and then press ;.
only when inputting analogue signals through the EXT 3
terminal.
Analogue
Digital (HDMI)
(D-Sub)
✔
✔
✔
✔
✔
✔
✔
✔
only be guaranteed if the video card conforms exactly to the
VESA 60 Hz standard. Any variations from this standard will
result in picture distortions.
Item
VESA standard
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
51