Application Advice; Maintenance & Service; Declaration Of Conformity - Skil 1048 Instructions Manual

- switch off tool 7b
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
• Grinding 8
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
• Cutting 9
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of
the cutting disc do the work
- do not brake cutting discs with side pressure
• Holding and guiding the tool
- always hold the tool firmly with both hands, so you
will have full control of the tool at all times
! while working, always hold the tool at the grey-
coloured grip area(s) 0
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots K 2 uncovered

APPLICATION ADVICE

• Instead of flange B 2 the "CLIC" quick-clamping flange
(SKIL accessory 10) can be used; grinding/
cutting discs can then be mounted without the use of
accessory keys
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially ventilation
slots K 2)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 00//EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ! will remind you of this when the need for
disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 045, EN 55014, in
accordance with the provisions of the directives
00/5/EC, 004/10/EC, 00/4/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
45 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
15.0.010
NOISE/VIBRATION
• Measured in accordance with EN 045 the sound
pressure level of this tool is  dB(A) and the sound
power level 10 dB(A) (standard deviation:  dB), and
the vibration ✱ (hand-arm method; uncertainty K =
1.5 m/s²)
✱ when surface grinding .5 m/s²
✱ when sanding . m/s²
! other applications (such as cutting-off or wire
brushing) may have different vibration values
• The vibration emission level has been measured in
accordance with a standardised test given in EN 045;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
significantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
significantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
F
Meuleuse d'angle
INTRODUCTION
• Cet outil sert au meulage, au tronçonnage et à
l'ébarbage de pièces en métal et en pierre sans utiliser
de l'eau; combiné avec des accessoires spécifiques,
cet outil peut également servir au brossage et au
ponçage
• Les opérations de coupe avec disques à tronçonner
abrasifs ne sont autorisées que si une protection de
tronçonnage (disponible en option comme
accessoire SKIL 2610Z00992) est utilisée
• Lisez et conservez ce manuel d'instruction 3
10
Jan Trommelen
Approval Manager
1048