Panasonic SC-BFT800 Operating Instructions Manual page 43

Video is not output.
≥ Set the "High Clarity Sound" in the Playback menu to "Off" to
use the VIDEO OUT terminal. (
Video is not output in high-definition.
≥ Confirm that "HDMI Video Format" in the Setup menu is set
properly. ( 40)
3D video is not output.
≥ Are the settings on this unit and the TV correct? (
3D video is not output correctly as 2D.
≥ Is the "Playback method for 3D disc" set to "2D Playback"?
( 38)
≥ Discs that have recorded titles with Side by side (2 screen
structure) which can be enjoyed in 3D are played back in
accordance with the settings of the TV.
A black band is displayed around the edge of the screen.
The aspect ratio of the screen is abnormal.
≥ Confirm the "TV Aspect" is set properly. (
≥ Adjust the aspect setting on the television.
(Adjustment using "Screen Aspect" (
possible.)
[For[the[United[Kingdom[and[Republic[of[Ireland[
After choosing "Home Cinema" in "Speaker Selection"
with the TV's remote control, the TV's input selection also
changes.
≥ Disconnect the HDMI cable from the TV and reconnect it to a
different HDMI IN terminal.
Sound
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
≥ Check connections to other equipment. (
≥ Ensure the speaker settings for your speakers are correct.
( 41)
≥ To output audio from a device connected with an HDMI cable,
set "HDMI Audio Output" to "On" in the Setup menu. (
≥ When "BD-Video Secondary Audio" is set to "On", Dolby
TrueHD, Dolby Digital Plus, DTS-HD Master Audio and
DTS-HD High Resolution Audio are output as Dolby Digital
or DTS Digital Surround.
≥ Re-master will not work when the bitstream signal is output
from the HDMI AV OUT terminal. (
≥ Depending on the connected equipment, the sound may be
distorted if this unit is connected with an HDMI cable.
≥ Select a suitable surround sound effect to optimise and enjoy
the original multi-channel source. (
36)
15)
39)
26) on the unit is also
14s18)
40)
36)
24)
Cannot switch audio.
≥ When audio is output from the HDMI AV OUT terminal, set
"Dolby D/Dolby D +/Dolby TrueHD", "DTS/DTS-HD" or
"MPEG Audio" to "PCM". (
No sound from the TV.
≥ Press [EXT-IN] to select the corresponding source. (
≥ The ARC (Audio Return Channel) function is not available.
Instead, use an optical digital audio cable to have the TV
sound. ( 14, 15)
≥ If the TV is not ARC compatible and only the HDMI
connection is used, an extra audio connection is necessary
( 14, 15).
≥ If there is no sound from the equipment connected to this
unit's DIGITAL AUDIO IN terminal, please make sure that
the optical audio output of the equipment is set to PCM.
iPod/iPhone operation
Cannot charge or operate.
≥ Check that the iPod/iPhone is connected firmly. (
≥ The battery of the iPod/iPhone is depleted. Charge the iPod/
iPhone, and then operate again.
Cannot display iPod/iPhone videos/photos on the TV.
≥ Make sure that TV is connected to the VIDEO OUT terminal
on this unit. ( 14)
≥ Operate the iPod/iPhone menu to make the appropriate
video/photo output settings for your TV. (Refer to operating
instructions for your iPod/iPhone.)
The TV input channel unintentionally changes to HDMI input.
≥ When the main unit is connected with an "HDAVI Control"
compatible TV and VIDEO IN is selected for iPod/iPhone
video or photo playback, the TV input channel will
automatically change to the HDMI input channel when
[START] is pressed.
jRe-select the TV's VIDEO IN input channel.
Radio
Distorted sound or noise is heard.
≥ Adjust the position of the antenna.
≥ Use an outdoor antenna. (
A beat sound is heard.
≥ Try to keep a certain amount of distance between the
antenna and the TV.
39)
23)
33)
16)
VQT2Z56
43