Table of Contents
Advertisement
For Reduced the VCR's Power
Consumption When the VCR Is Switched
Off
1
Press the MENU button T to display the Main menu on
the TV screen.
2
Press the Cursor buttons
(3421) Q to select "Display",
"Power save" and the entry field
for "Power save" in this order.
3
Press the Cursor buttons (34) Q to select "ON" or
"OFF".
ON: In this setting, the power consumption is greatly
minimised when the VCR is turned off (Standby
mode). In this case, the following happens:
≥ The item "VCR display" is automatically set to
"OFF".
≥ To turn the VCR on, keep the VCR-ON/OFF
button 1 pressed on the VCR main unit. It is not
possible to turn it on with the remote control.
≥ The Power save function works only when the
VCR is turned off (Standby mode). It does not
operate in the timer recording standby mode.
After all programmed timer recordings have been
made, and after all programmed data have been
erased, the VCR switches over to the Power
save mode.
≥ When the VCR is off, Pay TV programmes
cannot be watched on the TV because the signal
from the connected decoder is not looped
through. To watch them, turn on the VCR.
OFF: In this setting, the power consumption is not
reduced when the VCR is turned off (Standby
mode).
4
Press the OK button S to conclude the setting.
5
Press the EXIT button R to exit the On Screen Display.
For Automatic Change of the Brightness
of the VCR Display When the VCR Is
Switched Off
1
Press the MENU button T to display the Main menu on
the TV screen.
2
Press the Cursor buttons
(3421) Q to select "Display",
"VCR display" and the entry field
for "VCR display" in this order.
3
Press the Cursor buttons (34) Q to select the desired
condition.
≥ When the VCR is switched off, the brightness of the
VCR display is as follows:
ON:
Indications are brightly lit.
OFF:
Indications are not lit.
DIMMED:
Indications are dimly lit.
4
Press the OK button S to conclude the setting.
5
Press the EXIT button R to exit the On Screen Display.
36
Settings for the Main Menu Item
"Functions"
To Set the Type of External Source
Equipment that Is Connected to the AV2
21-pin Scart Socket
Main menu
1
Timer record
Channel Guide :OFF
Display
OSD :4:3
Tuning
Clock
Power save :OFF
Functions
VCR display :DIMMED
Language
2
Country
Satellite
3
4
5
To Set the Colour TV System Used During
Playback or Recording from an External
Source
1
2
3
4
Main menu
Timer record
Channel Guide :OFF
Display
OSD :4:3
Tuning
Clock
Power save :OFF
Functions
VCR display :DIMMED
Language
Country
Satellite
Press the MENU button T to display the Main menu
on the TV screen.
Press the Cursor buttons
(3421) Q to select
"Functions", "AV2" and
"DECODER" or "EXT" in this
order.
Press the Cursor buttons (34) Q to select the type of
external source equipment which is connected to
the VCR's AV2 21-pin socket.
≥ Set the external source equipment as follows:
DECODER: When a decoder is connected.
EXT:
When another VCR or a satellite
receiver is connected.
Press the OK button S to conclude the setting.
Press the EXIT button R to exit the On Screen Display.
Press the MENU button T to display the Main menu
on the TV screen.
Press the Cursor buttons
(3421) Q to select
"Functions", "TV system" and
"AUTO" in this order.
≥ The VCR automatically
distinguish between PAL, SECAM/MESECAM signals.
If the picture lacks colour during playback or during
recording from an external source, press the Cursor
buttons (34) Q to select "PAL" or "MESECAM".
Press the OK button S to conclude the setting.
Press the EXIT button R to exit the On Screen Display.
Main menu
Timer record
Display
AV2: DECODER
Tuning
TV system: AUTO
Clock
RFC system: DK
Functions
Remote: VCR 1
Language
Country
Satellite
Main menu
Timer record
Display
AV2: DECODER
Tuning
TV system: AUTO
Clock
RFC system: DK
Functions
Remote: VCR 1
Language
Country
Satellite
Advertisement
Table of Contents
