Tuning The Tv To Your Vcr - Panasonic NV-SJ200 Series Operating Instructions Manual

Tuning the TV to Your VCR

The VCR supplies a signal to the TV via the RF coaxial cable
on channel E21–E69 (For NV-SJ200BD and NV-SJ205
series) or E3–E4 (For NV-SJ200AM/AMC/AMM and NV-
SJ208AMJ).
It is possible to view the video picture on your TV in the same
way that you watch TV broadcasts.
If you have connected the VCR to the TV through the video
and Audio/Video input sockets, then you do not need to follow
the procedure below.
When the VCR is turned on after unpacking and
connecting the aerial cable and the mains lead, Plug in
Auto Tuning starts automatically.
Notes:
≥ If the VCR is turned on with the aerial not connected, all
channels are skipped. Therefore, firmly connect the aerial
and then turn the VCR off and on again to execute Auto
Tuning.
≥ When Auto Tuning is cancelled halfway, Auto Tuning is not
executed even if the VCR is turned off and then turned on
again. In this case, see page 9 "To Restart Plug in Auto
Tuning".
Operations
1
Turn on the TV and the VCR.
≥ Press the VCR/TV button
(For NV-SJ200AM/AMC/AMM and NV-SJ208AMJ)
2
Set the TV to an unused position which you wish to
use for your video playback.
≥ Tune the TV until the display shown on the below
appears on the screen. (Please refer to the TV
manufacturers operating instructions regarding
tuning.)
(For NV-SJ200BD and NV-SJ205 series)
≥ Set "RF SELECT" by pressing the Cursor buttons
(2 1) to select the colour TV system used by the
TV set to be connected.
BG: PAL B.G.H/SECAM B.G
I: PAL I
DK: PAL D/SECAM D.K.K1
On Screen Display
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 22 SEARCH
During Plug in Auto Tuning
3
Press the MENU button
8
to select the VCR mode.
NV-SJ200BD and
NV-SJ205 series
AUTO TUNING IS
COMPLETED.
RF SELECT RF SELECT BG
RF SELECT:
NV-SJ200AM/AMC/AMM
and NV-SJ208AMJ
AUTO TUNING IS
COMPLETED.
RF SELECT
µ
21 RF SELECT:
END: MENU
After Plug in Auto Tuning
.
To Change the RF output Channel
In some rare cases after tuning the TV to your VCR,
interference may be visible on the picture. To get rid of this
interference, you can manually adjust the RF output channel
a few channels up and down from the current setting. The
procedure is described below.
Operations
1 Hold down the MENU button
≥ The VCR display changes as shown below and the VCR
picture on the TV displays this pattern.
2 Enter the desired channel number (E3 or E4) (E21– E69)
by the Channel button
≥ Ensure that the VCR/TV switch
(For NV-SJ200AM/AMC/AMM and NV-SJ208AMJ)
(For NV-SJ200BD and NV-SJ205 series)
≥ Set the RF output channel of the VCR to "ss" (RF OFF)
when the VCR is connected to the TV via the Audio/
Video cable.
Press the Channel button
≥ It is also possible to select by pressing the Numeric
BG I ¡DK I DK
buttons
END: MENU
Example:
28:
3 Press the MENU button
BG I ¡DK
4 Retune your TV to the new RF channel for the VCR.
END: MENU
Note:
≥ Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
for 5 seconds or more.
VCR display
Example
.
is set to "VCR".
3 4
...
21
69
ss
(RF OFF)
to display "ss".
.
2 8
to finish the setting mode.
NV-SJ200BD and
NV-SJ205 series
Panasonic VCR
RF SELECT RF SELECT BG BG I ¡DK I DK
RF SELECT: END: MENU
NV-SJ200AM/AMC/AMM
and NV-SJ208AMJ
Panasonic VCR
RF SELECT BG I ¡DK
RF SELECT: END: MENU