Tuning The Tv To Your Vcr; Storing Tv Broadcasts In Your Vcr - Panasonic NV-HV62GCS Operating Instructions Manual

Tuning the TV to Your VCR

The VCR supplies a signal to the TV via the RF coaxial cable
on channel E21-E69.
If you have connected the VCR to the TV through the Audio/
Video input sockets, then you do not need to follow the
procedure below. To view the pictures from the VCR, set to
the AV mode on the TV with [AV] (2).
Preparation
• Turn on the TV and the VCR.
Operations
1 Set the TV to an unused position which you wish to
use for your video playback.
• Tune the TV until the display shown below appears on
the screen. (Please refer to the TV manufacturers
operating instructions regarding tuning.)
• Set [RF SELECT] by pressing [2 1] (28) to select the
colour TV system used by the TV set to be connected.
BG: PAL B.G.H/SECAM B.G
I: PAL I
DK: PAL D/SECAM D.K.K1
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 22 SEARCH 21
END: MENU
During Plug in Auto Tuning
2 Press [MENU] (9).
• If Auto Tuning stops halfway, refer to the right "To Restart
Plug in Auto Tuning".
To Change the RF output Channel
You can change the RF output channel, for example, when
interference occurs on the picture after tuning.
Operations
1 Hold down [MENU] (9) for 5 seconds or more.
• The VCR display changes as shown below and the VCR
picture on the TV displays this pattern.
Panasonic VCR
RF SELECT [BG] I DK
RF SELECT: END: MENU
2 Enter the desired channel number (E21-E69) by
[Numeric] (3) or [CH] (20).
• Set the RF output channel of the VCR to [ss] (RF OFF)
when the VCR is connected to the TV via the Audio/Video
cable.
• Press [CH] (20) to display [ss].
21
(RF OFF)
• It is also possible to select by pressing [Numeric] (3).
Example:
2 8
28:
3 Press [MENU] (9) to finish the setting mode.
4 Retune your TV to the new RF channel for the VCR.
Note:
• Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
AUTO TUNING IS
COMPLETED.
RF SELECT [BG] I DK
RF SELECT: END: MENU
After Plug in Auto Tuning
69
ss

Storing TV Broadcasts in Your VCR

The VCR is fitted with its own tuner (just like a normal TV) and
can be preset to receive up to 99 TV broadcast stations.
Plug in Auto Tuning
When the VCR is turned on after connecting the aerial cable
and the mains lead, Auto Tuning starts.
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 22
Auto tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned programme
position.
To Cancel Auto Tuning Mid-Operation:
Press [MENU] (9) during Auto Tuning.
If Auto Tuning stops halfway, follow the next procedures to
restart Plug in Auto Tuning.
To Restart Plug in Auto Tuning
If Auto Tuning stops halfway by cancelling or playback;
1 Press [STOP/EJECT] (40) and remove the video
cassette.
2 Keep both [CH] (20) I and J on the VCR pressed
simultaneously for 3 seconds or more during the VCR
on.
• The channel displayed on the VCR display disappears for
a moment then changes to 1.
3 Disconnect the mains lead and then reconnect it.
4 Turn off the VCR and then turn it on.
• Auto Tuning commences.
If Auto Tuning stops halfway by turning the VCR off or a
power failure,
Or if the VCR is turned on without the aerial connected
and all channels are skipped:
1 Disconnect the mains lead and then reconnect it.
2 Turn off the VCR and then turn it on.
• Auto Tuning commences.
SEARCH 21
END: MENU
5
LSQT0871