Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MAXDATA FUSION 6000 I
Summary of Contents for MAXDATA FUSION 6000 I
- Page 1 MAXDATA FUSION 6000 I User’s Manual...
- Page 2 Contents Contents...
-
Page 3: Table Of Contents
Installing and Removing a PCI Express x16 Card ..................27 Installing a PCI Express x16 Card .....................27 Removing the PCI Express x16 Card ....................27 Configuring the System for Intel Matrix Storage Technology for Serial ATA ........28 ® MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... - Page 4 Configuring the BIOS for Intel Matrix Storage Technology ............28 ® Creating your RAID set ........................28 Loading the Intel Application Accelerator Drivers ................28 ® Setting Up a “RAID Ready” System ....................28 Connecting Internal Headers .........................29 Front Panel Audio Header ........................30 IEEE 1394 Headers ..........................30 USB 2.0 Headers ..........................30 Front Panel Header ...........................31 Alternate Power LED Header ......................31...
- Page 5 7. USB 2.0 Header Signal Names ......................30 8. Front Panel Header Signal Names ....................31 9. Jumper Settings for the BIOS Setup Program Modes ..............33 10. Beep Codes .............................39 11. BIOS Error Messages ........................39 12. Product Certification Markings ......................41 MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I...
-
Page 7: Setting Up The System Workstation Position
ATTENTION In order to fully separate the workstation from current, the power cord must be removed from the wall outlet. ATTENTION To ensure stability, the floor stands must be turned outwards. MAXDATA FUSION 6000 I... -
Page 8: Connecting The System
Connecting the System Rear Connectors NOTE The line out connector, located on the back panel, is designed to power either headphones or amplified speakers only. Poor audio quality may occur if passive (non-amplified) speakers are connected to this output. Figure 1. -
Page 9: Board Features
• Intel BIOS BIOS ® • 8 Mbit symmetrical flash memory • Support for SMBIOS • Intel Rapid BIOS Boot ® • Intel Express BIOS Update ® RAID Intel Matrix Storage Technology for Serial ATA ® continued MAXDATA FUSION 6000 I... - Page 10 Table 1. Feature Summary (Continued) Peripheral Interfaces • Up to eight USB 2.0 ports • Four ports routed to the back panel • Four ports routed to two USB headers • Four Serial ATA channels, via the ICH6-R, one device per channel •...
-
Page 11: Board Components
USB 2.0 headers Processor fan header(4-pin, fan IEEE 1394 headers (blue) speed control) Main power connector (2x12) Speaker Diskette drive connector PCI bus add-in card connectors IDE connector Rear fan header (4-pin) Battery MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 12: Main Memory
Main Memory The mainboard supports dual or single channel memory configurations defined in Table 3. NOTE To be fully compliant with all applicable memory specifications, the board should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If your memory modules do not support SPD, you will see a notification to this effect on the screen at power up. -
Page 13: Audio Subsystem
Back panel audio connectors that are configurable through the drivers of the audio devices: Line in Three Line out Mic in or Center LFE out Two digital line out: • One coaxial line out • One optical (Toslink) line out MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 14: Input/Output (I/O) Controller
Input/Output (I/O) Controller The super I/O controller features the following: • Low pin count (LPC) interface • One serial port • One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) support • Serial IRQ interface compatible with serialized IRQ support for PCI systems •... -
Page 15: Enhanced Ide Interface
If both the supervisor and user passwords are set, you must enter either the supervisor password or the user password to access Setup. Setup options are then available for viewing and changing depending on whether the supervisor or user password was entered. MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 16: Chassis Intrusion
• Setting a user password restricts who can boot the computer. The password prompt is displayed before the computer is booted. If only the supervisor password is set, the computer boots without asking for a password. If both passwords are set, you can enter either password to boot the computer. -
Page 17: Suspend To Ram (Instantly Available Pc Technology)
Wake from USB USB bus activity wakes the computer from an ACPI S1 or S3 state. NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB. MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 18: Wake From Ps/2 Keyboard/Mouse
Wake from PS/2 Keyboard/Mouse PS/2 keyboard/mouse activity wakes the computer from an ACPI S1 or S3 state. PME# Wakeup Support When the PME# signal on the PCI bus is asserted, the computer wakes from an ACPI S1, S3, or S5 state. -
Page 19: Installing And Replacing Board Components
CAUTION Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations. MAXDATA FUSION 6000 I... -
Page 20: Installing A Processor
Installing a Processor Instructions on how to install the processor to the board are given below. Installing a Processor CAUTION Before installing or removing the processor, make sure that AC power has been removed by unplugging the power cord from the computer; the standby power LED should not be lit (see Figure 4 on page 17). Failure to do so could damage the processor and the board. -
Page 21: Remove The Processor From The Protective Processor Cover And Do Not Touch
Always replace the processor cover if the processor is removed from the socket (see Figure 8). Figure 8. Remove the Processor from the Protective Processor Cover and Do Not Touch MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 22: Install Processor
6. Hold the processor with your thumb and index fingers oriented as shown in Figure 9. Make sure fingers align to the socket cutouts (see Figure 9, F). Align notches (see Figure 9, G) with the socket see (Figure 9, H). Lower the processor straight down without tilting or sliding the processor in the socket. -
Page 23: Installing And Removing Memory
256 MB, 400 MHz DIMM 0 512 MB, 400 MHz DIMM 1 Channel B 256 MB, 400 MHz DIMM 0 512 MB, 400 MHz DIMM 1 Figure 12. Dual Configuration Example 2 MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 24: Dual Configuration Example 3
Three DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 (blue) and DIMM 1 (black) of channel A. Install a DIMM equal in speed and total size of the DIMMs installed in channel A in either DIMM 0 or DIMM 1 of channel B (see Figure 13). -
Page 25: Installing Dimms
7. Position the DIMM above the socket. Align the small notch at the bottom edge of the DIMM with the keys in the socket (see Figure 15). Figure 15. Installing a DIMM 8. Insert the bottom edge of the DIMM into the socket. MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 26: Removing Dimms
9. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place. Make sure the clips are firmly in place. 10. Reinstall the PCI Express x16 card if it was removed prior to installing the DIMMs. 11. -
Page 27: Installing And Removing A Pci Express X16 Card
3. Push back on the RM lever until the retention pin completely clears the notch in the card (Figure 16, 2). 4. Pull the card straight up (Figure 16, 3). � � � Figure 16. Removing the PCI Express x16 Card MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 28: Configuring The System For Intel ® Matrix Storage Technology For Serial Ata
Configuring the System for Intel Matrix Storage Technology ® for Serial ATA Configuring the BIOS for Intel Matrix Storage Technology ® 1. Assemble your system and attach two SATA hard drives. 2. Enter system BIOS Setup by pressing the <F2> key after the Power-On-Self-Test (POST) memory tests begin. -
Page 29: Connecting Internal Headers
�� �� ������ ������ ������������ ��� ������������� ������ ����� ��������� ������ � � � Figure 17. Internal Headers Chassis intrusion Alternate power LED Front panel USB 2.0 IEEE 1394 Front panel audio MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 30: Front Panel Audio Header
Front Panel Audio Header Figure 17, F shows the location of the yellow front panel audio header. Table 5 shows the pin assignments for the front panel audio header. Table 5. Front Panel Audio Header Signal Names Signal Name Signal Name Port1L Port1R Presence#... -
Page 31: Front Panel Header
No pin Alternate Power LED Header Figure 17, B shows the location of the alternate power LED header. Chassis Intrusion Header Figure 17, A shows the location of the chassis intrusion header. MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 32: Installing Other Connectors
Installing Other Connectors Figure 18 shows the location of the: • PCI bus add-in card connectors • PCI Express x1 connectors • PCI Express x16 connector • Floppy drive connector • IDE drive connector ����� ������ �� ����� ��������� ��������� Figure 18. -
Page 33: Setting The Bios Configuration Jumper Block
AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Find the configuration jumper block (see Figure 19). 5. Place the jumper on pins 2-3 as shown below. MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... - Page 34 6. Replace the cover, plug in the computer, turn on the computer, and allow it to boot. 7. The computer starts the Setup program. Setup displays the Maintenance menu. 8. Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a pop-up screen requesting that you confirm clearing the password.
-
Page 35: Setting Up Full 7.1-Channel Surround Sound (Optional)
Connect speakers to A, B, C, D, or E as shown in Figure 20, up to eight speakers. Multi-Channel Digital Audio Two types of S/PDIF connectors are available: coaxial (G) and optical (F). Select the proper connector according to the style of S/PDIF speakers to be used. MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... -
Page 36: Replacing The Battery
Replacing the Battery A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ±... - Page 37 Likvidácia použitých batérií sa musí vykonávať v súlade s miestnymi predpismi na ochranu životného prostredia. POZOR Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo. Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi. MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I...
- Page 38 To replace the battery, follow these steps: 1. Observe the precautions in “Before You Begin” on page 19. 2. Turn off all peripheral devices connected to the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter). 3.
-
Page 39: Bios
The time and/or date values stored in CMOS are invalid. CMOS Date/Time Not Set Run Setup to set correct values. DMA Error Error during read/write test of DMA controller. continued MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I... - Page 40 Table 11. BIOS Error Messages (Continued) FDC Failure Error occurred trying to access diskette drive controller. HDC Failure Error occurred trying to access hard disk controller. Checking NVRAM..NVRAM is being checked to see if it is valid. Update OK! NVRAM was invalid and has been updated.
-
Page 41: Regulatory And Integration Information
EN55022 (Class A) – Radiated & Conducted Emissions (European Union) • EN55024 (Immunity) (European Union) • CE – EMC Directive (89/336/EEC) (European Union) Product Regulatory Compliance Markings This product is marked with the following Product Certification Markings: Table 12. Product Certification Markings CE Mark MAXDATA FUSION 6000 I... -
Page 42: Electromagnetic Compatibility Notices
Electromagnetic Compatibility Notices Europe (CE Declaration of Conformity) This product has been tested in accordance to, and complies with the Low Voltage Directive (73/23/ EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to illustrate its compliance. -
Page 43: Installation Requirements
The suitability of this product for other applications or environments, (such as medical, industrial, alarm systems, test equipment, etc.) may require further evaluation. MAXDATA FUSION 6000 I MAXDATA FUSION 6000 I...
Need help?
Do you have a question about the FUSION 6000 I and is the answer not in the manual?
Questions and answers