Default Gateway Settings - Mitsubishi Electric XD8100U User Manual

Initial network settings (continued)
6. When selecting OK, the setting is completed as
the IP ADDRESS stored. However, when selecting
CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the
setting change dialog is displayed. After the
dialog disappears, the NETWORK menu is
displayed. If the entered content is not correct,
IP ADDRESS screen appears again after an
error dialog is displayed.
• It may take some time to refl ect the settings.
Subnet Mask Settings
1. Display the IP CONFIG menu.
2. Press the  or  button to select SUBNET MASK.
SUBNET MASK
3. Press the  or  button to select SET
4. Press the ENTER button.
• SUBNET MASK screen appears.
SUBNET MASK
255 . 255 . 255 .
0 1 2 3
OK
5. Enter the Subnet Mask.
• Refer to IP Address Settings for the detail of
entering.
6. When selecting OK, the setting is completed as
the Subnet Mask stored. However, when selecting
CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the
setting change dialog is displayed. After the
dialog disappears, the NETWORK menu is
displayed. If the entered content is not correct,
SUBNET MASK screen appears again after an
error dialog is displayed.
• It may take some time to refl ect the settings.

Default Gateway Settings

1. Display the IP CONFIG menu.
2. Press the  or  button to select DEFAULT
GATEWAY.
DEFAULT GATEWAY
3. Press the  or  button to select SET
4. Press the ENTER button.
• DEFAULT GATEWAY screen appears.
DEFAULT GATEWAY
10 . 132 .
0 1 2 3
OK
5. Enter the Default Gateway.
• Refer to IP Address Settings for the detail of
entering.
0. 0. 0. 0
.
0
← →
DEL
4 5 6 7 8 9 CLEAR
CANCEL
0. 0. 0. 0
.
1 . 1
← →
DEL
4 5 6 7 8 9 CLEAR
CANCEL
6. When selecting OK, the setting is completed as the
Default Gateway stored. However, when selecting
CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the
setting change dialog is displayed. After the
dialog disappears, the NETWORK menu is
displayed. If the entered content is not correct,
DEFAULT GATEWAY screen appears again after
an error dialog is displayed.
• It may take some time to refl ect the settings.
Enabling or disabling the network
certifi cation
You can select whether or not to certify the network
communication using the network password.
• For details, contact your dealer.
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the  or  button to select NET WORK
CERTIFICATION.
NETWORK CERTIFICATION
3. Press the ENTER button.
• Confi rmation dialog appears.
NETWORK CERTIFICATION :
4. Press the or  button to select ON
5. Press the ENTER button.
• To cancel the setting, press the MENU button.
• It may take some time to refl ect the settings.
Setting the control system
Set the control system.
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the  or  button to select CONTROL
SYSTEM.
CONTROL SYSTEM
3. Press the ENTER button.
CONTROL SYSTEM :
4. Press the or  button to select STANDARD ,
AMX , or CRESTRON .
STANDARD
Select this setting when using ProjectorView.
AMX
Select this setting when using the controller of
AMX. (See page 58.)
CRESTRON
Select this setting when using the controller or
software of Crestron Electronics, Inc. (See page 58.)
5. Press the ENTER button.
EN-51
ON
ON
OK : ENTER CANCEL : MENU
STANDARD
STANDARD
OK : ENTER CANCEL : MENU
or OFF .