Download  Print this page

Mitsubishi Electric UD8400U User Manual

Lan control utility.
Hide thumbs

Advertisement

LAN Control Utility

User Manual (for UD8400U)
1. Introduction ............................................................................................................ 2
1.1. Preparing to use network features .......................................................................................... 2
1.2. Functions and features ............................................................................................................ 2
1.3. Operation environment ............................................................................................................ 2
2. Setup ...................................................................................................................... 4
2.1. Installation of "ProjectorView Global+" .................................................................................... 4
2.2. When deleting "ProjectorView Global+" (Uninstallation) ......................................................... 5
3. Main screen ............................................................................................................ 6
3.1. System settings ....................................................................................................................... 8
4. Projector registration .............................................................................................. 9
4.1. Connection ............................................................................................................................... 9
4.2. Registration of projector to "ProjectorView Global+ ............................................................. 10
4.3. When changing the projector IP settings .............................................................................. 12
4.4. When changing projector settings ......................................................................................... 13
4.5. When deleting projector registration ..................................................................................... 13
5. Operation of projector .......................................................................................... 14
5.1. Operation of projector by remote controller .......................................................................... 14
5.2. Confirmation of projector status ............................................................................................ 15
6. Schedule setting ................................................................................................... 16
6.1. Creation of projector group ................................................................................................... 16
6.2. When changing schedule setting .......................................................................................... 17
6.3. When deleting group.............................................................................................................. 18
7. E-mail setting........................................................................................................ 19
7.1. Connection with E-mail server ............................................................................................... 19
7.2. E-mail setting ......................................................................................................................... 19
7.3. Sending test E-mail ................................................................................................................ 19
8. ProjectorView ....................................................................................................... 20
8.1. Main functions ....................................................................................................................... 20
8.2. Starting ProjectorView ........................................................................................................... 20
8.3. Entering projector information ............................................................................................... 23
8.4. Setting the network password ............................................................................................... 24
8.5. Resetting the network settings .............................................................................................. 24
9. Visual PA2 (Visual PA2 enabled projectors only) .................................................. 25
9.1. Starting Visual PA2 ................................................................................................................ 25
9.2. Saving messages entered and settings specified in Visual PA2 ........................................... 26
9.3. Loading saved data in Visual PA2 ......................................................................................... 26
9.4. Deleting data from Visual PA2 ............................................................................................... 26
9.5. Configuring the Schedule function of Visual PA2 .................................................................. 27
10. Telnet setup (Telnet enabled projectors only) ....................................................... 28
11. Others ................................................................................................................... 29
11.1. Troubleshooting ..................................................................................................................... 29
11.2. Supported Projectors ............................................................................................................ 29
Contents

Advertisement

   Related Manuals for Mitsubishi Electric UD8400U

   Summary of Contents for Mitsubishi Electric UD8400U

  • Page 1: Table Of Contents

    LAN Control Utility User Manual (for UD8400U) Contents 1. Introduction ......................2 1.1. Preparing to use network features ..................2 1.2. Functions and features ......................2 1.3. Operation environment ......................2 2. Setup ........................4 2.1. Installation of “ProjectorView Global+” ..................4 2.2.
  • Page 2: Introduction

    1. Introduction 1.1. Preparing to use network features This projector is equipped with the network function to control and monitor the projector’s operations and to send e-mail notification. Before using the network function, perform the following three preparation steps. • Installing the ProjectorView Global+ • Assigning the projector IP address • Configuring settings such as PASSWORD, E-mail Setting, Language, and Certification Setting by running Telnet (Telnet enabled projectors only) or using ProjectorView...
  • Page 3 1. Introduction Microsoft and Windows are the registered trademark or trademark of Microsoft Corporation in the United ® ® States and other countries. (The official name of Windows is Microsoft Windows Operating System.) Pentium is the trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
  • Page 4: Setup

    2. Setup 2.1. Installation of “ProjectorView Global+” Before starting installation, be sure to read “ReadMe.txt” contained in the CD-ROM. Copy ProjectorView Global+v3_1.msi contained in the Tools folder of CD-ROM to the hard disk of your personal computer. (1) Double click “ProjectorView Global+v3_1.msi”, and start up the installer of “ProjectorView Global+”. (2) The setup window is displayed. Click [Next]. (3) Select the folder to be installed, and click [Next].
  • Page 5: When Deleting "projectorview Global+" (uninstallation)

    2. Setup (5) When the installation has been completed, click [Close]. 2.2. When deleting “ProjectorView Global+” (Uninstallation) <Note> • When uninstalling “ProjectorView Global+”, “ProjectorView Global+” should be ended in advance. If the application continues operating, uninstallation can not be performed normally. (1) Double click “ProjectorView Global+v3_1.msi”, and start up the installer of “ProjectorView Global+”.
  • Page 6: Main Screen

    3. Main screen         Menu bar Configuration You can specify the following settings: Add New Group: You can create a new group. Edit Schedule Setting: You can edit schedule settings set for existing groups. Search Projector: Automatically searches available projectors. Assign IP: You can configure IP settings of the projector. Edit Projector Setting: You can edit projector settings. Edit E-mail Setting: You can configure E-mail settings used for this application. Search Projector Setting: You can specify a search range for communication with the projector via a router. System Configuration: You can configure system settings of this application. Help The version information is displayed. ...
  • Page 7 3. Main screen  Group Name Group of the projector can be selected. When you select “All”, all the registered projectors are displayed. Newly created group(s) are added to the list. When you select your choice of group, all projectors that belong to the selected group are displayed.
  • Page 8: System Settings

    3. Main screen 3.1. System settings (1) Select “System Configuration” from “Configuration” of the menu bar on the main screen. • “System Configuration” window is displayed. (Default settings are shown in the following example.) Item Description Language You can select the user interface language, Japanese or English. Refresh Status Cycle You can set the cycle to obtain the projector status. Select an integer value with no decimal part from 1 to 60 minutes. (2) Change the settings as needed and click [Save]. • To update the settings you changed, it is necessary to restart “ProjectorView Global+”.
  • Page 9: Projector Registration

    4. Projector registration 4.1. Connection Connect the controller PC and the projector, which have installed “ProjectorView Global+”, to a commercially available LAN cable. When connecting multiple projectors, use a commercially available hub. • A LAN terminal is required for the controller PC. • Use a LAN cable compatible with Category 5 and 100BASE-T. Use a crossover LAN cable in the case of connection example 1 and use a straight-through LAN cable in the case of connection example 2. (In the case of connection example 3, see the instruction manual of the router.) • Do not touch metal parts of the LAN terminal and LAN cable by hands charged of static electricity. Discharge of static electricity may cause a failure of the projector.
  • Page 10: Registration Of Projector To "projectorview Global

    4. Projector registration 4.2. Registration of projector to “ProjectorView Global+ The procedures to register projectors vary among the foregoing connection examples. • In connection examples 1 and 2 (where projectors are installed within the same local network), the projectors within such network are automatically detected and registered. For details, see procedure A below. • In connection example 3 (where projectors are installed via a router), specify the range of the projectors’ IP addresses and then carry out automatic projector search within the range to register projectors. For details, see procedure B below.
  • Page 11 4. Projector registration Procedure B - Connection example 3 (where projectors are installed via a router) To automatically detect projectors connected via a router, confirm the IP address in the projector network menu and specify a range of IP addresses to search that particular IP address using “Search Projector Setting”. <Note>...
  • Page 12: When Changing The Projector Ip Settings

    4. Projector registration <Note> • Set the default gateways of the projectors and PC correctly. For details, contact your network administrator. • Be sure to make a note of the IP addresses and default gateways you set. If you forget the setting values, you may not be able to detect the projectors again. • At initial setup, DHCP or Auto IP (169.254.0.1 through 169.254.255.254) automatically assigns an IP address. Note that a different IP address may be assigned every time you start the projectors. If a connection cannot be established, execute "Search Projector". • If you change the IP address in the projector menu after the projectors have been detected, execute “Search Projector”...
  • Page 13: When Changing Projector Settings

    4. Projector registration 4.4. When changing projector settings (1) Select the projector which you like to change from the projector list on the main screen. (2) Select “Edit Projector Setting” from “Configuration” of the menu bar. • “Edit Projector Setting” window is displayed. (3) Set the Projector Name and its group and the theft detector. Item Description Projector Name...
  • Page 14: Operation Of Projector

    5. Operation of projector 5.1. Operation of projector by remote controller Group or single unit of projector can be operated. (1) Select the projector which you like to operate from the projector list on the main screen. • When selecting more than one projector simultaneously, select while pressing the Ctrl key. (2) Click [Remote Controller] of the tool bar on the main screen or when you like to operate a certain projector, double click the projector on the projector list on the main screen.
  • Page 15: Confirmation Of Projector Status

    5. Operation of projector 5.2. Confirmation of projector status The status of the projector is displayed on the projector list on the main screen. Item Description Check Theft detector setting (ON/OFF) Projector list registration number Projector Name Projector name set in the application MAC Address MAC address of the projector IP Address...
  • Page 16: Schedule Setting

    6. Schedule setting 6.1. Creation of projector group Multiple projectors can be controlled and batched by sorting groups. Also, each group can set each time of the power supply ON/OFF every day. Since the schedule of the power supply ON/OFF is performed by each group, the projector which you like tooperate at the same schedule should be integrated into the same group. When Power ON and Power OFF are enabled, their time settings are indicated on the schedule list. [Example] When setting the schedule for the group “group 1”...
  • Page 17: When Changing Schedule Setting

    6. Schedule setting <Note> • The power supply ON and the power supply OFF can not be selected at the same time of the same day of the week. • The Schedule Setting will be executed while “ProjectorView Global+” is in operation. • Depending on usage conditions, such as when there are so many projectors that you need to control, the time to be executed by the power supply control may deviate from the setting time of the schedule. • When utilizing the Network Time Protocol (NTP) function on the Internet, the schedule operation may not be executed because the setting time of the schedule jumps over. • When the automatic time adjustment by summer time is valid, the schedule operation may not be executed because the time is automatically adjusted before and after switching over. 6.2. When changing schedule setting (1) Select a group which you like to change from the Group select pull-down menu on the main screen.
  • Page 18: When Deleting Group

    6. Schedule setting 6.3. When deleting group (1) Select the group which you like to delete from the Group select pull-down menu on the main screen. (2) Select “Edit Schedule Setting” from “Configuration” of the menu bar. • “Edit Schedule Setting” window is displayed. (3) Click [Delete]. • The selected group is deleted.
  • Page 19: E-mail Setting

    7. E-mail setting When the communication with the projector monitored by the theft detector is disrupted, a warning E-mail can be sent to the designated address, enabling to serve for early detection of the projector theft. The E-mail setting can not be set at every projector and every group. The same setting should be set for all projectors.
  • Page 20: Projectorview

    8. ProjectorView ProjectorView is a web-browser based remote control and monitoring tool for network projectors. If you use the projectors listed in page 29, see ProjectorView in “LAN Control Utility” User Manual included with the projector. <Note> • When CRESTRON is selected with the network menu, it becomes the Web control for CRESTRON. 8.1. Main functions • It displays the status of network projectors (such as the name of the projector, lamp temperature, lamp hours, errors and alerts).
  • Page 21 8. ProjectorView  ProjectorView main window (PROJECTOR INFORMATION) When you click PROJECTOR INFORMATION, the Projector Information window is displayed. To display the information, enter data in the Setup window. Click [PROJECTOR INFORMATION] to display the window on the left. Click [REMOTE CONTROL] to display the main window (REMOTE CONTROL).
  • Page 22 8. ProjectorView E-mail notification feature When there is something wrong with the projector, an E-mail notification is automatically sent to the designated address to post an alert or error message. To use this feature, enter the SMTP IP address, E-mail address, and E-mail from in the Setup window. (For details, see “8.3.
  • Page 23: Entering Projector Information

    8. ProjectorView 8.3. Entering projector information (1) Click [SETUP] in the ProjectorView main window (PROJECTOR INFORMATION). • Setup window is displayed. <Note> • Be sure to enter data within five minutes after the Setup window is displayed. Click OK to save changes. The connection will turn off in five minutes after the window is displayed so you need to go back to the main window (PROJECTOR INFORMATION) to access the Setup window.
  • Page 24: Setting The Network Password

    8. ProjectorView 8.4. Setting the network password (1) Click [PASSWORD] in the Setup window. • The window appears to enter the current network password. (2) Enter the current network password and click [OK]. (The default is "admin".) • If the password is correct, another window appears to enter a new one. • If the password is wrong, an error message is displayed. When you click [OK], the current network password window reappears. (3) Enter the New network password and Confirm network password, and then click [OK]. • If passwords entered match, the window closes to save the changes.
  • Page 25: Visual Pa2 (visual Pa2 Enabled Projectors Only)

    9. Visual PA2 (Visual PA2 enabled projectors only) Visual PA2 is a feature to display messages on the projector screen. It can be used for all active Visual PA2 enabled projectors. Additionally, the projector is capable of reading aloud on-screen messages using the Text Speech function. Note that some projectors may not have this function. See your projector User Manual for more information. <Note>...
  • Page 26: Saving Messages Entered And Settings Specified In Visual Pa2

    9. Visual PA2 (Visual PA2 enabled projectors only) 9.2. Saving messages entered and settings specified in Visual PA2 You can save messages entered in Textbox, as well as settings specified for Text, Frame, Location, and Text Speech. These must be saved before you activate the Schedule function in the Visual PA2 window. (1) Enter text in Textbox, specify settings for Text, Frame, Location, and Text Speech, and then click [Save].
  • Page 27: Configuring The Schedule Function Of Visual Pa2

    9. Visual PA2 (Visual PA2 enabled projectors only) 9.5. Configuring the Schedule function of Visual PA2 By using the Visual PA2’s Schedule function, your intended messages can be displayed on the screen at a set time. (1) Click [Edit] in the Schedule area. • "Visual PA2 Schedule" window is displayed. (The window below shows the example when the schedules have been entered in three rows.) ...
  • Page 28: Telnet Setup (telnet Enabled Projectors Only)

    10. Telnet setup (Telnet enabled projectors only) You can set the password for ProjectorView, a web-based remote control and monitoring tool for network projectors, and the industry standard protocol PJLink based remote projector management tool, the display language on the ProjectorView, the LAN controlled mode, and the PJLink certification mode by running Telnet on the projector screen. Telnet is not available when using other than the projectors listed in page 29.
  • Page 29: Others

    11. Others 11.1. Troubleshooting • The projector can not be recognized. The projector may not be recognized automatically due to the setting of fire wall. In such case, the communication of “ProjectorView Global+” should be registered as an exception to the fire wall. For the setting of the fire wall, see the manual of the software that configures the fire wall. • Operation by the remote controller can not be properly performed.

This manual also for:

Xd8100uUd8400u

Comments to this Manuals

Symbols: 0
Latest comments: