Table of Contents
Advertisement
Setting the Menus (Cont.)
REAR TERMINAL
Setting the operation mode of the
CALL OUT terminal (CALL OUT)
Sets the mode of call signal output
from the CALL OUT terminal. If any
abnormalities occur with the VCR
during recording, the call signal is
output from the CALL OUT terminal
on the rear panel regardless of CALL
OUT setting.
WRNG•TAPE END : The VCR outputs a call signal when the
tape reaches its end or when a
malfunction occurs. The VCR's function
when the tape ends depends on the
setting of TAPE END in FIRST TIME SET
UP menu (
WRNG•REMAIN
: The VCR outputs a call signal when a
malfunction occurs or when the tape has
approximately 3 minutes (at 3H mode) left.
WRNG
: The VCR outputs a call signal only when a
malfunction occurs.
Setting the recording mode and frequency division ratio
(CLOCK OUT)
Sets the recording mode and the frequency division ratio of
clock pulse output from the CLOCK OUT terminal.
• Setting the recording mode during the clock pulse output
REC
: When recording in any mode.
T/L REC
: When recording in time-lapse mode (L18H-
128H).
• Setting the frequency division ratio of the clock pulse output.
When JOG is turned, the display will be switched in the order
of 1
2
3
4
5
50
60
F (field)
The numbers 1 to 60 indicate the number of frames at 3H,
4H, 6H or 8H recording mode and the number of fields at
time lapse recording modes. (One frame consists of two
fields.) When set to F (field), one field is selected.
Setting the operation mode of the MODE OUT terminal
(MODE OUT)
A mode signal is output under the following circumstances.
REC
: During recording.
PLAY
: During playback.
POWER
: While the VCR is turned on.
TAPE IN
: When a tape is inserted in the VCR.
TAPE REMAIN
: When the tape has approximately 3
minutes (at 3H mode) left.
CLOCK ADJ
: When the clock indicates "00(min.):00(s)".
(The signal is output for 1 second only.)
Setting the operation mode of REC IN terminal (REC IN)
SERIES
: Recording starts when the signal is input.
REC-START/STOP : Recording continues while the signal is
input. If the signal is input for a short
period, the VCR may not start recording.
SYNC REC
: The video signal from the multiple of 3 or 5
cameras can be recorded separately by
connecting a switcher
(
page 14 for the menu setting and
page 20 for the connection).
24
Installation
<REAR TERMINAL>
CALL OUT
WRNG•TAPE END
CLOCK OUT
MODE OUT
REC IN
next column).
10
15
20
25
1
...
MAINTENANCE
Displaying the power loss list
(POWER LOSS LIST)
REC- 1
REC
page 14
SERIES
Displaying the alarm list (ALARM
LIST)
page 15
Initialising all menu settings (ALL MENU INITIALISE)
All menus will be initialised except timer programs.
1. Press MENU button.
•
<MAIN MENU> appears.
2. Turn JOG to select MAINTENANCE and turn SHUTTLE to
the right.
•
<MAINTENANCE> menu appears.
3. Turn JOG to select ALL MENU
INITIALISE and turn SHUTTLE to
the right.
•
<ALL MENU INITIALISE>
menu appears.
4. Turn SHUTTLE to the left.
•
The setting of all menus (except TIMER PROGRAM) will
return to its initial setting.
To exit the menu without initialising all menus, press the
MENU button.
5. Press MENU button.
•
The day and present time display appears on screen.
Clearing the power loss list (POWER LOSS LIST CLEAR)
page 15
Clearing the alarm list (ALARM LIST CLEAR)
page 15
30
Displaying number of tape use (REPEAT REC TIMES)
page 15
Displaying the elapsed time of VCR (ELAPSED TIME)
page 15
FIRST TIME SET UP
Setting the present time, date and
Daylight Saving Time settings (TIME
DATE ADJUST)
page 21
Setting operation of VCR when the
tape reaches its end during
recording or playback (TAPE END)
The VCR's function when the tape reaches its end during
recording is as follows:
STOP
: The tape stops, the indication "End" appears on
REWIND
: Rewinds the tape to the beginning and stops
Note
A point to notice
the fluorescent display and "TAPE END" on
screen. When CALL OUT is set to WRNG•TAPE
END, a call signal is output from the CALL OUT
terminal.
(except during timer recording). When CALL
OUT is set to WRNG•TAPE END and a tape
reaches its end, a call signal is output for 2
seconds from the CALL OUT terminal.
Supplementary information
Info.
<MAINTENANCE>
POWER LOSS LIST
ALARM LIST
ALL MENU INITIALISE
POWER LOSS LIST CLEAR
ALARM LIST CLEAR
<REPEAT REC TIMES>
0
<ELAPSED TIME>
0H
ALL MENU INITIALISE
Turn the SHUTTLE RING
then all MENU will be
initialised.
<FIRST TIME SET UP>
TIME DATE ADJUST
TAPE END
STOP
QUASI V-SYNC
ON
VIDEO MODE
COLOUR
TAPE LENGTH
E-180
BUZZER
WRNG
Advertisement
Table of Contents
