Table of Contents
Related Manuals for Midas HERITAGE 3000
Summary of Contents for Midas HERITAGE 3000
- Page 1 EXTENDER OPERATORS MANUAL Klark Teknik Group, Klark Teknik Building, Walter Nash Road, Kidderminster. Worcestershire. DY11 7HJ. England. Tel:+44 (0) 1562 741515 Fax:+44 (0) 1562 745371 Email: pro_audio_group@compuserve.com Website: midasconsoles.com...
-
Page 3: Declaration Of Conformity
Declare that a sample of the following product:- Product Type Number Product Description Nominal Voltage (s) Current Freq Midas Heritage 3000 to which this declaration refers, is in conformity with the following directives and/or standards:- Directive(s) Test Standard(s) EN 55013: 1990 EN 50082: 1992... - Page 5 ATTENTION! The following special limitations apply to the console and must be observed in order to maintain safety and electromagnetic compatibility performance: POWER CONNECTION The console should only be operated with the power supply connected to ground via its mains supply connector. CONTROL CONNECTIONS The console should only be operated with high quality screened control cables.
- Page 7 Contents Midas HS0001 Mono Input Module Page 1 Midas HS0003 Input Fader Page 2 Midas HS0004 Stereo Input Module Page 8 Midas HS0003 Input Fader Page 13 Midas Can Interface Kit Page 15...
- Page 9 MIDAS HS0001 gain direct o/p Mono Input freq bell treble Module freq hi-mid lo-mid freq bell bass freq freq MONO stereo image mute MIDAS HS0001...
- Page 10 The 48V switch connects 48 volt phantom power to the input connector which is suitable for a condenser microphone or DI box. The PAD switch gives 25dB of The GAIN control gives continuous attenuation to the input signal which will adjustment of the input amplifier allow the connection of high output gain from + 15dB to + 60dB.
- Page 11 The LO MID (dual concentric top) control gives continuous adjustment of boost and cut from + 15dB to - 15dB with a 0dB centre detent. The lo mid FREQ control gives continuous adjustment of the frequency The lo mid WIDTH (dual concentric range that the lo mid equaliser acts on bottom) control gives continuous from 100Hz to 2k.
- Page 12 The configurable group MIX controls (1 to 24) have two functions:- i. They operate as bus assign ON/OFF switches by way of a non latching The aux PRE switches only operate push/push action with LED status when in one of the AUX bus modes; indication.
- Page 13 The PAN defaults to control the channel placement within a group or master The ST switch connects the post fader stereo mix and has a constant power law channel signal to the master stereo bus i.e. - 3dB at the centre position. via the pan control.
- Page 15 MIDAS HS0003 Input Fader safe’s safe’s safe’s safe’s safe’s safe’s safe’s safe’s MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE solo solo solo solo solo solo solo solo AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO MIDAS MIDAS HS0003...
- Page 16 The SOLO switch sends the input channel The SAFE switches disable remote signal to the PFL mono and AFL stereo control of the channels as follows:- busses. If the switch is pressed for a short time it will latch on or off, but if it is held i.
- Page 17 MIDAS HS0004 gain balance Stereo Input freq bell treble Module freq hi-mid lo-mid freq bell bass freq freq MONO mute & MIDAS HS0004...
- Page 18 The 48V switch connects 48 volt phantom power to both input connectors and is suitable for condenser microphones or DI boxes. The PAD switch gives 25dB of attenuation in both input signals to allow The GAIN control gives continuous the connection of high output adjustment of the input amplifier gains microphones or line level signals.
- Page 19 The LO MID control gives continuous adjustment of left and right boost and cut from +15dB to -15dB with a 0dB centre detent. The lo mid FREQ control gives continuous adjustment of the frequency range that the lo mid equalisers act on The lo mid HI Q control changes the from 100Hz to 2k.
- Page 20 The configurable group MIX controls (1 to 24) have two functions:- i. They operate as bus assign ON/OFF switches by way of a non latching push/push action with LED status indication. The aux PRE switches only operate when ii. They adjust the levels sent from the in one of the AUX bus modes;...
- Page 21 The left and right PAN controls are used to place the input channel signals within a stereo group or stereo master mix. As well as image placement, the controls can also adjust the image width from stereo through mono to reverse stereo (left and right crossed over).
- Page 23 MIDAS HS0003 Input Fader safe’s safe’s safe’s safe’s safe’s safe’s safe’s safe’s MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE solo solo solo solo solo solo solo solo AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO MIDAS MIDAS HS0003...
- Page 24 The SOLO switch sends the input channel The SAFE switches disable remote signal to the PFL mono and AFL stereo control of the channels as follows:- busses. If the switch is pressed for a short time it will latch on or off, but if it is held i.
- Page 25 MIDAS CAN INTERFACE KIT...
- Page 26 H3000 EXTENDER PART LIST Extended internal CAN cable. Internal RS-232 cable. CAN interface main, BC3026. External 5m long CAN cable. INSTRUCTIONS FOR INSTALLATION Before starting any work ensure consoles are switched OFF. Lift out the VCAfader blocks and remove the old internal CAN cable which runs the length of the console. Place the new extended internal CAN cable in the fader tray and connect all the VCA fader blocks to it.
- Page 27 Main and extender consoles viewed from above. Extender console Figure 1. Back of main console viewed from above. ! $ Figure 2.
- Page 28 HS3000/2000 16 EXTENDER POWER SUPPLY CONNECTION. The HS3000 16 extender can be powered from 1 or 2 power supplies connected as follows:- 2 X Heritage PSU 1 X Heritage PSU or XL2900 Main Console Extender 2268.00 2268.00 2 X Heritage PSU 2 X Heritage PSU or XL2900 Main Console Extender...
- Page 29 gain gain gain gain gain gain gain gain direct o/p direct o/p direct o/p direct o/p direct o/p direct o/p direct o/p direct o/p freq freq freq freq freq freq freq freq bell treble bell treble bell treble bell treble bell treble bell...