KitchenAid YKHMS2050SW0 Installation Instructions Manual

Microwave hood combination
Table of Contents

Advertisement

Available languages

Available languages

MICROWAVE
HOOD
COMBINATION
INSTALLATION
INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 30" (76.2 cm) wide. See
"Installation Requirements" section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the
illustration in these installation instructions.
INSTRUCTIONS
D'INSTALLATION
DE L'ENSEMBLE
FOUR A MICRO-ONDES/HOTTE
Ce produit est con_u pour rutilisation au-dessus d'appareils de cuisson 61ectriques ou _.gaz de 30" (76,2 cm) de largeur
ou moins. Voir la section "Exigences d'installation"
pour d'autres remarques.
Ces instructions d'installation sont valables pour plusieurs modules. II se peut que I'apparence de votre propre module soit
16g&rement diff6rente de celle montr6e sur les illustrations dans ce document.
Table of Contents
/ Table des mati_res
MICROWAVE
HOOD COMBINATION
SAFETY ....................... 1
............................................
2
Tools and Parts .......................................................................
2
Location Requirements ...........................................................
2
Product Dimensions ................................................................
3
Electrical Requirements ..........................................................
3
..............................................
4
Remove Mounting Plate ..........................................................
4
Convert Microwave Oven to External Venting ........................ 4
Locate Wall Stud(s) .................................................................
6
Mark Rear Wall ........................................................................
7
Drill Holes in Rear Wall ............................................................
7
Attach Mounting Plate to Wall ................................................
8
Prepare Upper Cabinet ...........................................................
8
Install the Microwave Oven .....................................................
9
Complete Installation ...........................................................
10
...................................
11
ASSISTANCE ...........................................................................
12
Replacement Parts ...............................................................
12
SleCURITle DE L'ENSEMBLE FOUR .& MICRO-ONDES/HOTTE...13
EXIGENCES D'INSTALLATION .........................................................
13
Outillage et pieces ...........................................................................
13
Exigences d'emplacement
..............................................................
14
Dimensions du produit ....................................................................
14
15
..................................................
15
D_pose de la plaque de montage ...................................................
15
Four & micro-ondes
- conversion pour d_charge & I'ext_rieur ....... 15
mural ............ 17
Trac_ sur le mur arri_re ...................................................................
18
Pergage de trous dans lemur arriere ..............................................
19
Fixation de la plaque de montage sur lemur .................................
19
Preparation du placard mural ..........................................................
20
Installation du four & micro-ondes
..................................................
21
Achever I' installation ........................................................................
22
SPleCIFICATIONS/CONCEPTION
ASSISTANCE ......................................................................................
24
Pieces de rechange .........................................................................
24
MICROWAVE
HOOD COMBINATION
SAFETY
Your safety and the safety of others are very important.
We have provided
many important
safety
messages
in this manual
and on your appliance.
Always
read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow
instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
8206646

Advertisement

Table of Contents
loading

Summary of Contents for KitchenAid YKHMS2050SW0

  • Page 1: Table Of Contents

    MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS This product is suitable for use above electric or gas cooking products up to and including 30" (76.2 cm) wide. See "Installation Requirements" section for further notes. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions.
  • Page 2: Installation Requirements

    INSTALLATION REQUIREMENTS The microwave oven is set for recirculation installation. For external (wall or roof) venting, see "Venting Design Specifications" section. 4 ..• _i .._ _ __ _._ _.._ _. Check the opening where the microwave oven will be installed. Tools Needed The location must provide: Gather the required tools and parts before starting installation.
  • Page 3 Installation Dimensions NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See "Electrical Requirements" section. Electrical Shock Hazard Plug into a grounded 3 prong outlet. (83.2 cm) 3ica_* 12" (30.5 cm) min. Do not remove ground prong. Do not use an adapter.
  • Page 4: Installation Instructions

    INSTALLATION INSTRUCTIONS NOTE: To avoidpossible damage tothework surface, c overthe work surface. _." ;;> 1. Remove any remaining contents from the microwave oven The microwave oven is set for recirculation installation. For wall or cavity. roof venting, changes must be made to the venting system. See 2.
  • Page 5 When the vent deflector is as far back as it can easily slide, flip 3. Save the cover for possible change of venting method in the future. it so that the wide side is to the back of the microwave oven, and the narrow side (with holes) is down.
  • Page 6 Ieca eWal5 d(s) NOTE: If no wall studs exist within the cabinet opening, do not 1. Using a stud finder, locate the edges of the wall stud(s) within install the microwave oven. the opening. See illustrations in "Possible Wall Stud Configuralons." 2.
  • Page 7 Wall Venting Installation Only The microwave oven must be installed on a minimum of 1 wall Centerline Upper cabinet bottom stud, preferably 2, using a minimum of I lag screw, preferably 2. 1. Using measuring tape, find and clearly mark the vertical centerline of the opening.
  • Page 8: Locate Wall Stud(S)

    Wall Stud at One Corner Hole (Figure 3) NOTE: Secure t hemounting plate tothewall a tbothbottom 1. With the support tabs of the mounting plate facing forward, corner holes drilled i ntothewall s tuds and/or drywall using either insert a 1/4-20 x 3" round-head bolt through the corner hole 1/4-20 x 3"round-head bolts and toggle nuts or1/4x2"lag that fits over the 3/4"...
  • Page 9 5. Cut the 11/2 '' (3.8 cm) diameter hole at the circular shaded area 6. Drill 3/8" (10 mm) holes at points "D" and "E" on the template. These are for two 1/4-20 x 3" bolts and washers used to "G"...
  • Page 10 10.With themicrowave oven centered, and withatleast o ne 2. Connect vent to damper assembly. person h olding i tinplace, insert bolts through u pper c abinet intomicrowave oven. Tighten b olts until t here isnogap between upper cabinet andmicrowave oven. NOTES: •...
  • Page 11: Venting Design Specifications

    VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and Rectangular to Round Transition builder/contractor reference only. NOTE: The minimum 3" (7.6 cm) clearance must exist between NOTES: the top of the microwave oven and the rectangular to round transition piece so that the damper can open freely and fully.
  • Page 12: Assistance

    Recommended Vent Length ASSISTANCE A 31/4"x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used. Call your authorized dealer or service center. When you call, you will need the microwave oven model number and serial number. The total length of the vent system including straight vent, Both numbers can be found on the model and serial number elbow(s), transitions and wall or roof caps must not exceed the...
  • Page 13: Exigences D'installation

    SECURITE DE L'ENSEMBLE FOUR A MICRO-ONDES OTTE Votre s6curit6 et celle des autres est tres importante. Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous toujours lire tousles messages de securite et de vous y conformer. Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves &...
  • Page 14: Specifications

    Dimensions & respecter Iors de I'installation REMARQUE : La prise de courant a 3 alveoles reliee & la terre dolt _tre situee a I'interieur du placard mural. Voir la section Inspecter I'espace ou le four a micro-ondes sera install& "Specifications electriques".
  • Page 15: Instructions D'installation

    INSTRUCTIONS DE LIAISON .&.LA TERRE [] Pour tout appareil menager connecte par un cordon de courant electrique II faut que le four & micro-ondes soit relie & la terre. En cas de court-circuit electrique, la liaison & la terre reduit le risque de choc electrique car le courant electrique dispose d'un itineraire direct d'acheminement &...
  • Page 16 Installation du d_flecteur 4. Fixer le deflecteur avec 2 vis de montage (1 a chaque extremite). 1. Tirer doucement sur les anneaux pour soulever/enlever grille au sommet du four a micro-ondes. A. Sommet du four a micro-ondes B. Grille de ventilation C.
  • Page 17 Positionner adequatement le module du volet de sortie : la 2. Utiliser une pince coupante - decouper doucement les points de fixation du couvercle de fermeture. patte Iongue s'ins_re dans la fente du c6te droit de I'ouverture - voir I'illustration. Fixer le module du volet de sortie avec la vis de montage.
  • Page 18: Identifier La Position Du/Des Poteaux Du Colombage Mural

    Un trou d'angle face & un poteau du colombage mural Deux trous des angles face & un poteau Figure 3 du colombage mural Figure 4 A. Trous des angles (sur la plaque de montage) B. Axe vertical central de I'ouverture clans le placard C.
  • Page 19 Pour une installation avec d_charge murale seulement Un trou d'angle face & un poteau du colombage mural (Figure 3) 1. Percer un trou de 3/16" (5 mm) a travers le poteau mural I'emplacement du trou d'angle marque a I'etape 3 de la Axe central_ Fond d_ip/l_eard mural...
  • Page 20: Pergage De Trous Dans Lemur Arriere

    Pousser les deux vis avec ecrou articule & travers le panneau de gypse; visser les visa la main pour verifier que chaque ... _: ...._...._;1 _ ;_ _: ecrou articule s'est deploy6 et prend appui contre le panneau Interrompre I'alimentation electrique.
  • Page 21 4. Alors que I'avant du four & micro-ondes est encore incline, enfiler le cordon d'alimentation a travers le trou de passage perce dans le fond du placard mural. Risque du poids excessif Utiliser deux ou plus de personnes pour d_placer et installer le four a micro-ondes, Le non=respect de cette instruction peut causer une blessure au dos ou d'autre blessureo...
  • Page 22 Pour une installation avec d_charge & I'ext_rieur travers le toit seulement 1. Pour I'installation des filtres sur I'appareil, voir le Guide d'utilisation et d'entretien. 1. Inserer le module du volet de sortie dans I'ouverture d_coupee dans le placard : la patte Iongue du module dolt s'inserer dans la fente a gauche de I'ouverture decoupee - voir I'illustration.
  • Page 23: Du Circuit D'i_'Vacuation

    SPECIFICATIONS DU CIRCUIT D'EVACUATION Cette section presente de I'information de reference uniquement, & I'intention des architectes/concepteurs et constructeurs. REMARQUES Raccord de transition rectangulaire/rond • Les materiaux du circuit d'evacuation necessaires & REMARQUE : On doit disposer d'un espace libre de 3" (7,6 cm) I'installation ne sent pas fournis avec I'ensemble four a micro- ou plus entre le sommet du four a micro-ondes...
  • Page 24: Assistance

    Longueur recommand6e du circuit d'6vacuation ASSISTANCE On devrait utiliser un conduit rectangulaire 31/4 '' x 10" (8,3 x Appeler le marchand local autorise ou le centre de service agre& 25,4 cm), ou un conduit rond de dia. 6" (15,2 cm). Lors de I'appel, vous aurez besoin des numeros de modele et de La Iongueur equivalente totale du circuit d'evacuation, ceci...

This manual is also suitable for:

Ykhms2050ss0Ykhms2050sb0

Table of Contents