Advertisement
Parts supplied:
Not shown:
• literature pack
• orifice spuds
2 screws
(#10 x 1-I/2")
anti-tip
bracket
2 plastic
anchors
Bracket must be securely mounted to sub-floor.
Thickness of flooring may require longer screws to
anchor bracket to sub-floor. Longer screws are
available from your local hardware store.
• burner grates and caps
vent cap
• LP conversion orifice spud kit:
1 - 0.95 mm cooktop (blue)
2 - 0,67 mm cooktop (black)
1 - 1.05 mm cooktop (green)
1 - #65 broil burner
Tools needed:
Assemble
the required
tools
and parts
before
starting
installation.
Read and
follow
the instructions
provided
with
any
tools
listed
here.
level
flat-blade
screwdriver
Phillips screwdriver
putty knife
pipe wrench
3/8" drive ratchet
3/8" and 5/16" combination
wrenches
hand or electric
drill
channel
lock pliers
measuring
tape or ruler
wood floors:
1/8" drill bit
concrete/ceramic
floors:
3/16" carbide4ipped
masonry
drill bit
(Hammer
may be needed for anchors.)
Materials needed:
° gas line shutoff
valve
• 1/2" male pipe thread
nipple for connection
to pressure
regulator
• LR gas-resistant
pipe-joint
compound
• AGA or CSA design-certified
flexible
metal
appliance
connector
(4-5 feet) (1.2-1.5 m} or
rigid gas supply
line as needed
• Insulated
pad or !/4" (6 mm) plywood
if
range is installed
over carpeting
Electrical requirements
Emectrical
Shock
Hazard
Plug
into
a grounded
3 prong
outlet.
Do not remove
ground
prong.
Do not use an adapter.
Do not use an extension
cord.
Failure
to follow
these
instructions
can
result
in death,
fire, or electrical
shock.
If codes
permit
and a separate
ground
wire
is used,
it is recommended
that
a
qualified
electrician
determine
that the
ground
path
is adequate
and that the
outlet
is correctly
polarized.
Do not ground
to a gas pipe.
Check
with
a qualified
electrician
if you
are not sure
range
is properly
grounded.
A 120-volt,
60-Hz,
AC-only,
lO-ampere,
fused
electrical
supply
is required.
A
time-delay
fuse
or circuit
breaker
is
recommended.
It is recommended
that a
separate
circuit
serving
only
this
appliance
be provided.
Electronic
ignition
systems
operate
within
wide
voltage
limits,
but proper
grounding
and polarity
are necessary.
In addition
to checking
that
the outlet
is
correctly
grounded,
the outlet
must
be
checked
by a qualified
electrician
to see if
it is wired
with
correct
polarity.
IMPORTANT:This
range
is equipped
with
an electronic
ignition
system
that
will
not
operate
if plugged
into
an outlet
that
is
not properly
polarized.
A wiring
diagram
is included
on the
back
of the range.
See "Cabinet
dimensions/requirements"
for recommended
location
of electrical
outlet.
Recommended
ground
For personal
safety,
this
range
is
equipped
with
a power
supply
cord
having
a 3 prong
ground
plug.To
minimize
possible
shock
hazard,
the cord
must
be plugged
into
a mating
3 prong,
ground-type
outlet,
grounded
in
accordance
with
the National
Electrical
Code, ANSI/NFPA
70 --
latest
edition
_, or
CSA Standard
C22.1 Canadian
Electrical
Code,
Part 1 -- latest
edition
x×-, and aii
local
codes
and ordinances.
If a mating
outlet
is not available,
it is the
personal
responsibility
and obligation
of
the customer
to have a properly
polarized
and grounded,
3 prong
outlet
installed
by a qualified
electrician.
3 prong
ground plug
\
3 prong properly polarized
ground-type outlet
power supply
cord
Copies of the standards listed may be obtained
from:
National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts, 02269
_ CSA International
8501 East Pbasant Valley Rd.
Cleveland, Ohio 44131-5575
Advertisement
