Yamaha DTXTREME III Owner's Manual page 74

Reference
Basic Structure of the DTXTREME III
Paramater
name
GateTime Determines the gate time of the sliced portion.
Determines the center frequency of the high EQ
H.Freq
band that is attenuated/boosted.
Determines the amount of boost or attenuation
H.Gain
applied to the high EQ band.
Height Determines the height of the simulated room.
Determines the amount of time from the moment a
HiAtk note is played to the moment the compressor is
applied to the high frequencies.
HiGain Determines the output gain for the high frequencies.
HiLvl Determines the level of the high frequencies.
HiMute Switches the mute status of the high frequencies.
[For MULTI BAND COMP]
HiRat Determines the ratio of the compressor for the high
frequencies.
[For REVERB effects]
HiRat
Adjusts the resonance of the high frequencies.
Determines the minimum input level at which the
HiTh
effect is applied to the high frequencies.
Determines the speed of the horn when the slow/fast
HornF
switch is set to "fast."
Determines the speed of the horn when the slow/fast
HornS
switch is set to "slow."
Determines the Cutoff frequency of the High Pass
HPF
Filter.
Determines the amount of time that elapses between
InitDly
the direct, original sound and the initial reflections.
InitDly1 Determines the delay time for the 1st series.
InitDly2 Determines the delay time for the 2nd series.
InitDlyL Determines the delay time of the left channel.
InitDlyR Determines the delay time of the right channel.
InpLvl Determines the input level.
Selects mono or stereo configuration for the input
InpMode
sound.
InpSelect Selects an input.
Determines the center frequency of the low EQ band
L.Freq
that is attenuated/boosted.
Determines the amount of boost or attenuation
L.Gain
applied to the low EQ band.
L/RDiffuse Determines the spread of the sound.
L/RDpth Determines the depth of the L/R pan effect.
Determines the lagging time additionally applied to
the delayed sound, and is specified via a note length.
Lag
This helps in setting rhythmic effects that match the
timing of the music.
[For CHORUS effects, RING MODULATOR, CLAS-
SIC FLANGER, TEMPO FLANGER]
LFODpth Determines the depth of the modulation.
[For TEMPO PHASER]
Determines the depth of the phase modulation.
Determines the L/R phase difference of the modu-
LFOPhDiff
lated wave.
LFOPhRst Determines how the initial phase of the LFO is reset.
[For CHORUS effects, TREMOLO, RING MODULA-
TOR, CLASSIC FLANGER, TEMPO FLANGER]
Determines the frequency of the modulation.
[For TEMPO PHASER]
LFOSpeed Determines the modulation speed via a note length.
This helps in setting rhythmic effects that match the
timing of the music.
[For AUTO PAN]
Determines the frequency of the Auto Pan.
[For CLASSIC FLANGER, RING MODULATOR]
Selects the wave for modulation.
[For AUTO WAH]
LFOWave
Selects the wave, sine or square.
[For AUTO PAN]
Determines the panning curve.
74
DTXTREME III Owner's Manual
Descriptions
Paramater
name
Determines the decay characteristics of Early Reflec-
Livenss
tion.
Determines the amount of time from the moment a
LowAtk note is pressed to the moment the compressor is
applied to the low frequencies.
LowGain Determines the output gain for the low frequencies.
LowLvl Determines the output level for the low frequencies.
Determines whether the low frequency band is off or
LowMute
on.
[For MULTI BAND COMP]
LowRat Determines the ratio of the compressor for the low
frequencies.
[For REVERB effects]
LowRat
Determines the ratio of the low frequencies.
Determines the minimum input level at which the
LowTh
effect is applied to the low frequencies.
LPF Determines the cutoff frequency of the low pass filter.
Determines the Resonance of the Low Pass Filter for
LPFReso
the input sound.
Determines the center frequency of the middle EQ
M.Freq
band that is attenuated/boosted.
Determines the amount of boost or attenuation
M.Gain
applied to the middle EQ band.
M.Width Determines the width of the middle EQ band.
[For FLANGER]
Determines the offset value of the delay modulation.
Manual
[For PHASER MONO, PHASER STEREO]
Determines the offset value of the phase modulation.
MicAngl Determines the L/R angle of the microphone.
Determines the amount of time from the moment a
MidAtk note is pressed to the moment the compressor is
applied to the mid frequencies.
MidGain Determines the output gain for the mid frequencies.
MidLvl Determines the output level for the mid frequencies.
MidMute Switches the mute status of the mid frequencies.
Determines the ratio of the compressor for the mid
MidRat
frequencies.
Determines the minimum input level at which the
MidTh
effect is applied for the mid frequencies.
Mix Determines the volume of the effect sound.
Determines the level of the effect sound mixed to the
MixLvl
dry sound.
ModDpth Determines the depth of the modulation.
Determines the depth of the modulation for the right
ModDptR
channel as offset.
Determines the phaser type, or more specifically, the
Mode
factor for forming the phaser effect.
ModFB Determines the feedback level to the modulation.
ModGain Determines the gain of the modulation.
Determines the cutoff frequency of the low pass filter
ModLPF
applied to the modulated sound.
Determines the resonance of the low pass filter for
ModLPFReso
the modulated sound.
Determines the mix balance of the modulated ele-
ModMix
ment.
Determines the L/R phase difference of the modu-
ModPh
lated wave.
ModSpd Determines the modulation speed.
ModWave Selects the wave type for modulation.
Determines how long it takes to move the sound from
MoveSpeed the current status to the sound specified via the
Vowel parameter.
Determines the resonance of the low pass filter
NoiseQ
applied to the noise.
Determines the cutoff frequency of the low pass filter
NoisLPF
applied to the noise.
NoisLvl Determines the noise level.
Descriptions