Advertisement
frontto back.
If the rangeis not level,pull range
forwarduntilthe rearlevelinglegis
removedfromthe anti-tipbracket.
Adjustthe levelinglegsup or down.
Thenslide rangebackinto position.
Check that levelingleg is engaged in
anti-tipbracket.
NOTE: O venmustbelevelfor
satisfactory bakingconditions.
All connections mustbewrench-
tightened.
1/2" (1.3 cm) flare union adapters
Assemble
the flexible
connector
from the gas supply pipe
to the pressure regulator,
located in
the lower left side of the storage
drawer area, in this order: shutoff
valve, 1/2" (1.3 cm) flare union
adapter, flexible
connector,
1/2"
(1.3 cm) flare union adapter. Seal all
openings
in floor or wall wherever
range is installed.
5
[] Use pipe-joint
compounds
appropriate
for use wdth L.R gas to
seal all gas connections,
if flexible
connectors
are used, be certain
connectors
are not kinked.
Open the shutoff valve in
the gas supply line. Wait a few
minutes
for the gas to move through
the gas line.
[] Test for gas leaks. Leak testing
of the Cooking Center shall be conducted
according to the following instructions:
Test all connections by brushing on an
approved non-corrosive leak-detection
solution. Bubbles will show a leak. Correct
any leak found.
Plug power supply cord into
grounded
outlet.
O__
burner
cap
" urner
base
_a
burner
te
Remove cooktop
burner
caps and grates from parts package.
Align notches in burner caps with
pins in burner base. Burner caps
should
be level when properly
positioned.
Place burner grates over
burners
and caps.
EJectronic
ignition
System
Initial lighting
and gas flame
adjustments.
Cooktop
and oven burners
use
electronic
ignitors
in place of
standing
pilots. When the cooktop
control
knob is turned to the "LITE"
position,
the system creates a spark
to light the burner.This
sparking
continues,
as long as control
knob is
turned
to "LITE'_
When the oven control
is turned to
the desired setting, a glow bar heats
up bright orange and ignites the gas.
No sparking
occurs and the glow bar
remains on while the burners
operate.
Check
I
the operation
of
the cooktop
burners.
Push in
and turn each
_ "--__
/
control
knob to
@o ' • _ _ _,p
the "LITE"
e_o MSO
position. The
_o
flame should
light within
4 seconds.The
first time
a burner is lighted it may take longer
than 4 seconds to light because of
air in gas line.
[] if burners
do not light
properly,
turn
cooktop
control
knob
to the "OFF"
position.
Check that the
power
supply
cord
is plugged
in and
the circuit
breaker
or fuse has not
blown.
Check that the gas shutoff
valves
are set to the "OPEN"
position.
Repeat
Step
18. if a burner
does
not light
at this
point,
contact
your
dealer
or authorized
service
company
for assistance.
Top burner flame appearance:
low
flame
2
[] Adjust the height of top
burner flames (some models).
The cooktop
LOW burner flame
should be a steady blue flame
approximately
1/4" (0.64 cm) high.
it can be adjusted
using the
adjustment
screw in the center of the
valve stem.The
valve stem is located
directly
underneath
the control knob.
If the LOW flame needs
to be adjusted:
__J"
a. Remove the
control knob.
b. Hold the
knob stem
with a pair
of pliers,
adjustment
Use a small
flat-head
screwdriver
to turn the screw located in the
center of the control knob stem
until the flame is the proper size.
c. Replace the control
knob.
d.Test the flame by turning
the
control from "LO" to "Hi'; checking
the flame at each setting.
3[]
Remove the oven rack.
Remove the oven bottom
and place
it on a protected
surface.
Advertisement
