Mixer Features - Numark MIX DECK Quick Start Manual

MIXER FEATURES

1. MASTER VOLUME – Adjusts the output volume of the
Program mix.
2. BOOTH VOLUME – Adjusts the Booth output level.
3. CHANNEL GAIN – Adjusts the channel's pre-fader and pre-
EQ gain level.
4. CHANNEL TREBLE – Adjusts the high (treble) frequencies
of the corresponding channel.
5. CHANNEL MID – Adjusts the mid-range frequencies of the
corresponding channel.
6. CHANNEL BASS – Adjusts the low (bass) frequencies of
the corresponding channel.
7. INPUT SELECTOR – Selects the input source to be routed
to the corresponding channel. Input jacks are located on the
rear panel (plus the USB port on the top panel).
8. CHANNEL FADER – Adjusts the audio level on the
corresponding channel.
9. CROSSFADER – Blends audio playing between Channels 1
and 2. Sliding this to the left plays Channel 1 and sliding to
the right plays Channel 2.
10. DOCK – Connect your iPod here. Gently rock the iPod back
and forth over the connector when attaching or removing it.
11. DOCK ADJUSTER – Turn this knob accordingly so your
docked iPod rests against the support.
12. iPod CONTROLS – Functions as the controls for your iPod's
menus and Touchwheel while it is plugged into the mixer.
13. iPod VOLUME – Adjusts the audio level on the iPod
channel.
14. CUE SOURCE – Selects the audio that is sent to the
headphones. Switch it to "iPod" to hear the iPod. Switch it
to "MASTER" to hear the Program mix. Switch it to "CH1
CH2" to hear Channels 1 and 2 in the Cue channel.
15. CUE SLIDER – Previews the audio playing on Channels 1
and 2. Sliding this to the left plays Channel 1. Sliding to the
right plays Channel 2.
16. CUE GAIN – Adjusts the level of the headphone audio.
17. LED METERS – Monitors the audio level of the Program mix.
DECK FEATURES
1. EJECT – Press this button to eject the CD. If a CD is
currently playing, this button will have no effect.
2. USB – Connect your favorite USB storage device to this
connector to allow the MIXDECK to read and play back
your music files. The MIXDECK only supports the MP3
format so please make sure that your audio files are
encoded as MP3s if you would like to use them with the
MIXDECK.
Note: MIXDECK supports the HFS+, FAT and NTFS files
systems. HFS+ GUID Partition Table is not supported at
this time.
3. SOURCE – Press the SOURCE button and turn the
PARAMETER knob to choose which audio source you
want to play; CD, USB, or you can use the MIXDECK as
a USB MIDI controller. This button will not function if the
MIXDECK is currently playing.
4. TRACK KNOB – Used to skip from track to track, for
folder navigation and as an "enter" button.
5. BACK – When navigating a CD or device with folders,
this button will take you back to the previous level
(folder).
6. PLAY – Starts the music. The music will begin playing
from either the cue point or the last point of pause.
Pressing this button while the unit is playing will restart
the song from the last set cue point, which can be used
to create a "stutter" effect.
2
3
4
17
5
6
7
8
2
26
27 28
3
24
25
23
17
13
12
12
10
1
8
5
11
10
12
12 12 12
17
12
15
16
14
13
9
31
20
5
29 30
18 18 18
21 22
19 19 19
9
11
7 6
1
3
4
5
6
7
8
4
14
15
16