Electrical Connection - Fisher & Paykel DS603SS Installation Instructions Manual

,.. DOUBLE MODELS
WATER CONNECTION
RecommendedHOT
(Maximum 140°F/60°0).
Supplied hoseto suit 3/8" (gmm)
male compressionfitting.
WATER SOFTENER MODELS
Referto your DishDrawer® UserGuidefor
how to set up your water softener.
DishDrawer
227/16"
I_ (57°L_m)
5/16" k --.
/Smm) |
_ " _/ | I (2rnm)
_'_o_ [ |l Tab
#
%
227/16"
{578mm)
237/16"
(595mm)
WATER PRESSURE Maximum Minimum
Water Softener Models 145 p.s.i. (1000kPa) 14.5 p.s.i. (100kPa)
Other Models 145 p.s.i. (1000kPa) 4.3 p.s.i. (30kPa)
BRAIN CONNECTION
Drain HoseJoiner to suit O3/4 ' ' +_5/64", O 5/8 ' '
+_ 5/64"
and
O1" +_5/84"waste tees.
ELECTRICAL CONNECTION
110-120 VACpoweroutlet,9 AmpsMinimum.
LENGTH OF SERVICES (FROM PRODUCT E XITPOINT)
Drain hose-
889/16"
(2250mm)
Inlet hose- 687/8 " (1750mm)
Power supply cord - 44" (1125mm)
NOTE:Servicesapproximately exit product 77/16 ' ' (189mm) from left;
215/8 ' ' (550mm) from front; 311/4 '' (793mm) from top.
(520mm)
Drawer Open
Prefinished model shown 2" - 43/8" +
* For an Integrated DishDrawer® the (50-1 lOmm) !
product depth is specified with an
11/16" (18mm} Integrated Panel thickness.
** Depth of product excludes Curvature (13/18" (30mm} Prefinished only,}
or Handle.
"_TOE KICK DEPTH
Prefinished 8 F/at Door 2"-43/8" (50-1 lOmm);
/ntegrated 5" (127mm)less the ToeKick Panelthickness. Minimum Panel
thickness using the supplied screws is 3/8" (gmm).
# BOOR FRONT HEIGHT
Prefinished 8 F/at Door 305/64"(764mm);
/ntegrated 281/4 '' (717.5mm) minimum.
4 5/16"
(109.5mm!,
Min thickness
of cavity sides
is 5/8" (16mm)
Screw
9/16"
(14mm)
1/2"
from front of cabinetry (13m m)
• z
f
,,< ............ _ _ ....... _" [ countert
.................................... _\ [i _ ....................... _ l °_r=,_
< _ " Moisture n
90° Protection tape
A_
E Tape
LO::
r.D_
C_4_
A
E
E
t._
m,
0 11/2" (38mm)
services hole
÷ _ immediately
,, j adjacent to corner,
_, can be either side
/ 22r7/{' (580mm) X \ t oughout cavity
23 %" (600mm)
1/2" (13mm)
Thesemarks indicate mounting tab screw
locations (refer to step 1 page 7)
NOTE: All depth measurementsare taken
from the front face of the adjacentcabinetry.
i_WARNING!
Be sure the edges of the services hole
are smooth or covered. If the services
hole is through a metal partitionthe hole
must be protectedwith the EdgeProtector
providedto prevent damage te the power
cordor hoses.