Fisher & Paykel DS603SS Installation Instructions Manual page 2

._.BEFORE YOU START- DOUBLE S#NGLE MODELS
DOUBLE MODELS
Flexible Extrusion ........ FlexibleExtrusion
for Sides (2) for Top(1)
Edge Protector (1) @ Clamp @
(1) Washer
(1)
Drain Hose Drain Hose Wire
Support (1) Joiner (1) Clips (2)
Installation Tabs(2)
Phillips 16ram
Screws (7)
Moisture
Protection
Tape(1)
p/n 527208
Prefinished
ToeKick (1)
Whiteprefinished toe kick kit p/n 526678
or Black prefinished toe kick kit p/n 526679
or Iridium prefinished toe kick kit p/n 527109
SINGLEMODELS
Drain Hose
/ /
Support (1) _. /
'<_'J Drain Hose
Joiner (1)
_ Clamp (1)
Ftexib/eExtrusionfor Sk:/es(2)
DishDrawer
Ph%t?s 16ram
Screws(5)
Moisture
Protection
Ta-pe _ '1,_
p/n 527208
C_
[,¢'#sher ( 1)
Drill 8 No.2 PhillipsBit
No.2 PhillipsScrewdriver
FlatScrewdriver
Adjustable Wrench or M5 Socket
O11/2"(38mm) Hole Saw
Side Cutting Pliers
Wooden ChoppingBoard
TapeMeasure
Spirit Level
Safety Glasses
Utility Knife
Pencil
Sandpaper
SPARE PARTS INSTALLATION KITFOR SINGLE 8 DOUBLE MODELS: p /n 526676
ELECTRICAL PREPARATION
A) The switched power outlet must be outside the DishDrawer®
cavity so that it is accessibleafter installation.
B) The switched power outlet must be between 6" (150mm) and
18" (450mm) from the DishDrawer® cavity.
C) Referto Page9, Step 5 for electrical connection options.
Important!
The services hole in the DishDrawer® cavity needs to be large
enough for the plugon the power supply cordto fit through, but MUST
NOT be more than 11/z" (38ram).
PLUMBING 8 DRAINAGE PREPARATION
,4) A readily accessiblevalve must be installed in the water supply pipe.
B) If the supply pressure exceeds 145 psi (1000kPa),then a pressure
limiting valve must be used.
C) Review PlumbingOptionson pages4 or 6. Choosea methodthat best
suits your needs.
B) A Drain Hose extensionKit P/N 525798 will extend the drain hoses
by 1413/4"(3.6m). The kit is availablefrom the nearest FisherSPaykel
AuthorizedServiceAgent. DO NOTextend beyondthis limit.
E) This Dishwasher'smaximum drain height is 371/2 '' (950mm).
CAVITY PREPARATION
A) The self-adhesivemoisture protection tape must be appliedto the
undersideof the countertop to prevent moisture damage,(refer to
cavity diagrampg 3 or 5). Be sure surfaces are dry and dust-free
prior to application.
B) Be sure the cavity provides sufficient materialto secure the DishDrawer®
using the mounting tabs (refer to step 1, page 7). If there is
nothingto screw to, add a brace. Seepage 3 or 5 for screw locations.
C) The services hole MUSTbe immediately adjacentto the rearlower
corner of the cabinetry. If not, the hoseswill preventthe
DishDrawer® being pushedback into the cavity all the way. The hole
can be located on either side dependingon the location of the
services.
B) Be sure the cavity sides are plumb (vertical) as this will assist with
levellingthe DishDrawer®.
E) Minimum clearances:
POWER SUPPLY CORD
A) Careshould be taken when the applianceis installedor
removed to reducethe likelihoodof damageto the power
supply cord.
B) If the power supply cord is damaged,it must be replacedby
the Manufacturer,Service Agent or a similarly qualified person
in orderto avoid a hazard.
GROUNDING INSTRUCTIONS
A) This appliancemust be grounded. In the event of malfunction or
breakdown,groundingwill reducethe risk of electric shock by
providing a path of least resistancefor electric current.
/_WARNING!
Improper connectionof the equipment-grounding conductorcan result
in a risk of electric shock. Check with a qualified electrician or
service representativeif you are in doubt as to whether the appliance
is properlygrounded.
B) This applianceis equippedwith a power supply cord having an
equipment-groundingconductor andan earthing plug. The power
supply plug must be plugged into an appropriateoutlet that is installed
and earthed in accordancewith all local Codesand Ordinances.
z_WARNING!
Do not modify the power supplyplug providedwith the appliance - if
it wiJJ notfit the outlet, have a properoutlet installed by a qualified
electrician. Do not use an extension cord,adaptor plug or multiple
outlet box.