Utility; Config. Page; Card Page - TC Electronic FireworX User Manual

SYSTEM & MIDI
The Utility display
In the Utility display, you can choose between Config.
and Card. Use the < > Arrow keys to select between
the two displays.
The Config. Page
In the Config. page you can set up a number of global parameters
for the FireworX such as memory protect, MIDI bulk dump etc.
Viewing Angle
Adjust for best contrast of the LCD display.
Sticky Tempo page
Determines whether the Tempo page sticks on until another key
is pressed or disappears automatically after a few seconds.
Param. dial direction
This parameter enables you to change the cursor direction when
dialing the Parameter wheel. Choose whether the cursor should
move up or down when dialing the parameter wheel clockwise.
DSP load check mode
Selects the repsonse of the FireworX when the DSP limit is
exeded. When set to "Secure", the outpus of the FireworX will
be muted when the DSP power limit is exeded. When set to
"Free", the FireworX will continue to play, however the sound is
must likely to be corupted until you reduce the number of effect
blocks in the Routing.
Pedal Type
Switches between momentary and alternating. This parameter
should be set to alternating if
you are using an expression
pedal.
Pedal Calibration
Press Enter to enable
calibration of the External
input jack on the back panel of
the FireworX. Follow the
instructions in the display.
Protect
Sets the Preset Protect function
On/Off.
Protect Low limit
Sets the lower limit of the
Preset protect. The current
number is included in the
protection.
Protect High limit
Sets the higher limit of the
Preset protect. The current
48

Utility

Config
User Interaction
Display Viewing Angle
Sticky Tempo page
DSP Load check Mode
Environment
Pedal calibration
Pedal type
User Bank protect
Protect
Protect Lo-limit
Protect Hi-limit
MIDI Bulk dump
User Bank to MIDI
MIDI to User Bank
number is included in the protection.
MIDI Bulk Dump
You can backup the User Presets of the FireworX to another
FireworX or to MIDI recording device using these functions.
User Bank to MIDI
Connect your FireworX's MIDI Out to another FireworX, a
sequencer or any other MIDI recordable device. Press Enter
twice and the FireworX will perform a MIDI bulk dump of all
User Presets.
MIDI to User Bank
Connect the storing device to the FireworX's MIDI In and press
Enter. The FireworX is now ready to receive a MIDI bulk dump
containing User Presets.
WARNING: This action will overwrite ALL existing User Presets
in the FireworX.
The Card page
The Card page features a number of tools for handling Cards,
including Preset copying to and from Card.
Use the Parameter wheel to scroll, and the Value wheel to change
values. Card type: SRAM PCMCIA, type 1, min. 64 K byte.
Show Card status
This function makes it possible to check the status of your PC-
Card. The FireworX will be able to display the size of the card,
the write protection status, the number of Presets on the Card and
the amount of free space.
NOTE: This information will only be available when the card is
FireworX formatted or contains FireworX Presets. The FireworX
will read "New Card" when the Card is inserted if the Card is not
formatted.
Format/Erase Card
This function will Format and Erase the PC-card. Press Enter
twice to confirm this action.
WARNING: This action will overwrite ALL existing Presets on
the current Card.
User/Card Bank copy
This section makes it possible to copy a specified group of
Presets to or from a specific space on a Card. For example: You
want to copy User Preset 10-15 from the FireworX to Preset 5-10
on your Card. Now set the "User Bank Preset start" at 10
(because you start the group of Presets at #10), the "Card Bank
Preset start" at 5 (because you want the first copied Presetto start
at #5), the "Number of Presets" to 5 (because that is the number
of Presets you want to copy). Now select Copy "From User Bank
to Card" scroll to "Execute copy" and press Enter twice to