Related Manuals for Fujitsu MB2146-09A-E
Summary of Contents for Fujitsu MB2146-09A-E
- Page 1 FUJITSU SEMICONDUCTOR SS01-00024-1E SUPPORT SYSTEM MC Family BGM ADAPTER MB2146-09A-E OPERATION MANUAL...
- Page 2 This manual describes how to handle the F MC family BGM adapter. Be sure to read it before using the product. For information on the MCUs supported by this product, contact the Fujitsu sales or support repre- sentative. * : F MC is the abbreviation of FUJITSU Flexible Microcontroller.
- Page 3 ■ Caution of the products described in this document The following precautions apply to the product described in this manual. Indicates a potentially hazardous situation which, if not avoided appropriately, WARNING could result in death or serious injury and/or a fault in the user’s system. Electric shock, Before performing any operation described in this manual, turn off all the power supplies to the system.
- Page 4 (i.e., submersible repeater and artificial satellite). Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.
-
Page 5: Optional Parts
2. Optional Parts A variety of optional parts are available for this adapter that may be purchased separately as needed. Consult a Fujitsu sales or support representative for details. 3. Appearance and Part Names Figures 1 and 2 show the adapter appearance, major dimensions and part names. -
Page 6: System Configuration
The adapter connects the host computer and the serial interface of MCU with built-in flash memory made by Fujitsu, and writes data in a built-in flash memory. For information on the USB programmer, contact the Fujitsu sales or support representative. Figure 4 shows the system configuration when the adapter is used as a USB programmer. - Page 7 5. Connections ■ Connection to the host computer Connect the adapter to the host computer using the USB cable. Figure 5 shows how to connect the USB cable. Connection to the USB connector of the adapter Adapter Figure 5 Connecting the USB cable ■...
-
Page 8: Specifications
Weight *1 : The maximum and minimum voltages depends on the MCU used. For details, contact the Fujitsu sales or support representative. *2 : Does not include the power consumption of the MCU. *3 : The part number of the connector is: FAS-1001-2101-0BF (YAMAICHI ELECTRONICS Co., Ltd.) ■... - Page 9 ■ Tool reset specifications A tool reset is a hardware reset by the adapter to reset the entire system of the MCU (including the BDSU module) on the user system. When both of the adapter power and MCU’s user power are turned on, the tool reset is canceled au- tomatically to enable the MCU to be evaluated.
- Page 10 ■ Adapter interface specifications The pinouts of the adapter interface connectors mounted on the user system are shown in Tables 3 and 4. The recommended connectors are listed in Table 5, and the pin configuration is shown in Fig- ure 7. When the adapter interface connector is mounted on the user system, connect the MCU to the adapter interface connector according to the following specifications.
- Page 11 Table 5 Recommended adapter interface connectors Part number Specifications Manufacturer FAP-1001-2202-0BF Right-angle solder dip Housing provided, Middle latch provided YAMAICHI FAP-1001-2204-0BF Straight solder dip Housing provided, Middle latch provided ELECTRONICS FAP-10-08#2-0BF Right-angle solder dip Housing provided, Latch not provided Co., Ltd. FAP-10-08#4-0BF Straight solder dip Housing provided, Latch not provided...
- Page 12 Table 6 DC specifications of the user interface Connector Circuit type Resistor connection Remarks pin number (mA) (mA) (µA) Connected to GND via Connected to UVCC Open drain output 64.0 * by 10kΩ bus switch* ± 5 * CMOS input ±...
- Page 13 SS01-00024-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM MC Family BGM ADAPTER MB2146-09A-E OPERATION MANUAL August 2007 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept.