Check Operation - Frigidaire PLGF659GCA Installation Instructions Manual

7. Moving the AppNiance for
Servicing and Cmeaning
Turn off the range line fuse or circuit breakers at tile main
power source, and turn off the manual gas shut-off valve.
Make sure the range is (:old. Remove the service drawer
(warmer drawer on some models) and open the oven door.
Lift the range at the front and slide it out of the cut-out
opening without creating undue strain on the flexible gas
conduit. Make sure not to pinch the flexible gas conduit at
the back of the range when replacing the unit into the cut-
out opening. Replace the drawer, close the door and switch
on the electrical power and gas to the range.
8. Check Operation
Refer to the Use and Care Guide packaged with the
range for operating instructions and for care and
cleaning of your range.
Remove all packaging from the oven before testing.
8.1 Install Burner Bases and Burner Caps
This range is equipped with sealed burners
as shown (see Figure 5).
It is very important to make sure that all of the Surface
Burner Heads, Surface Burner Caps and Surface Burner
Grates are installed correctly.
I. Remove all packing tape from cooktop. Remove Burner
Caps and Burner Heads (See Figure 6A).
2. Discard all packing material located under all Burner
Heads.
3. To correctly place Burner Heads & Caps, match tile
letters located under center of Burner Caps with the
letters located inside Burner Head (See Figure 6A).
4. Match the letters stamped on Burner skirts with Burner
Heads and Burner Caps on cooktop. Carefully align the
Electrodes into slots of tile Burner Heads (Figure 6B).
Note: The Burner Heads should sit flat on Cooktop
Burner Skirts.
Burner
Cap
Figure 6A
5. Unpack Burner
Grates and position on
cooktop.
NOTE: There are no
burner adjustments
necessary on this
range.
must align into slot
for each Burner Head
8.2 Turn on Electrical Power and Open Main
Shutoff Gas Valve
8.3 Check the Igniters
Operation of electric: igniters should be checked after
range and supply line connectors have been carefully
checked for leaks, and range has been connected to
electric: power. To check for proper lighting:
a.Push in and turn a surface burner knob to tile LITE
position. You will hear the igniter sparking.
b. The surface burner should light when gas is available
to the top burner. Each burner should light within four
(4) seconds after air has been purged from supply
lines. Visually check that burner has lit.
c. Once the burner lights, the control knob should be
rotated out of tile LITEposition.
There are separate ignition devices for each burner. Try
each knob separately until all burner valves have been
checked.
8.4 Adjust the "LOW" Setting of Surface
Burner Valves (see Figure 7}
a.Push in and turn each control to LITE until burner
ignites.
b. Quickly turn knob to LOWEST POSITION.
c. lf burner goes out, readjust valve as follows:
Reset control to OFF. Remove the surface burner
control knob, insert a thin-bladed screw driver into tile
hollow valve stem and engage the slotted screw
inside. Flame size can be increased or decreased with
the turn of the screw. Adjust flame until you can
quickly turn knob from LITEto LOWEST POSITION
without extinguishing the flame. Flame should be _s
small as possible without going out.
Figure 7
8.5 Operation of Oven Burners and Oven
Adjustments
8.5.1 Electric Ignition Burners
Operation of electric: igniters should be checked after
range and supply line connectors have been carefully
checked for leaks, and range has been connected to
electric power.
The oven burner is equipped with an electric control
system as well as an electric oven burner igniter. If your
model is equipped with a waist-high broil burner igniter, it
will also have an electric burner igniter. These control
systems require no adjustment. When the oven is set to
operate, current will flow to tile igniter. It will "glow"
Figure 6B
5