Frigidaire PLGF659GCA Installation Instructions Manual page 6

similar to a light bulb. When the igniter has reached a
temperature sufficient to ignite gas, the electrically
controlled oven valve will open and flame will appear at
the oven burner. There is a time lapse from 30 to 60
seconds after thermostat is turned ON before tile flame
appears at the oven burner. When the oven reaches the
display setting, the glowing igniter will go off. The burner
flame will go "out" in 20 to 30 seconds after igniter goes
"OFF". To maintain any given oven temperature, this cycle
will continue as long as tile display is set to operate.
After removing all packing materials and literature from
tile oven:
a) Set the oven to BAKE at 300%. See Use & Care Guide
for operating instructions.
b) Within 60 seconds the oven burner should ignite. Check
for proper flame (see 8.5.2), and allow the burner to
cycle once (see cycle explanation above). Reset controls
to off.
c) If your model is equipped with a waist-high broiler
burner, set oven to broil. See Use & Care Guide for
operating instructions.
d) Within 60 seconds the broil burner should ignite. Check
for proper flame (see 8.5.3). Reset controls to off.
8.5.2 Oven Burner FJame Adjustment
Tube
Orifice Hood
F-I
8,5.3 BroiJ Burner FJame Adjustment
The approximate flame length of tile burner is I inch
(distinct inner cone of blue flame). To determine if the
broil burner flame is proper, set the oven to broil. If flame
is yellow, increase air shutter opening size (see "2" in
Figure 9). If the entire flame is blue, reduce the air shutter
opening size. To adjust, loosen lock screw (see "3" in
Figure 9), reposition air shutter, and tighten lock screw.
9. Make Sure Range is Levem
Check if the range is level by placing a level horizontally
on an oven rack. Check diagonally from front to back,
then level the range by either adjusting the leveling legs or
by placing shims under the corners of the range as
needed.
Figure 8
gh Burner
Shutter
Lower Oven Bottom
Air Shutter (removable)
Tile approximate oven burner flame length is 1 inch
(distinct inner cone of blue flame).
To determine if the oven burner flame is proper,
remove the oven bottom and burner baffle and set
the oven to bake at 300°F.
To remove the oven bottom, remove oven hold down
screws at rear of oven bottom. Pull up at rear,
disengage front of oven bottom from oven front
frame, and pull the oven bottom out of the oven.
Remove burner baffle so that burner flame can be
observed.
If the flame is yellow, increase air shutter opening size
(see "2" in Figure 9). If the entire flame is blue, reduce
the air shutter opening size.
To adjust flame loosen lock screw (see "3" in Figure
g), reposition air shutter, and tighten lock screw.
Replace oven bottom.
When All Hookups are Complete
Make sure all controls are left in tile OFF position.
Make sure the flow of combustion and ventilation air to
the range is unobstructed.
Model and Serial Number Location
The serial plate is located on the oven front frame
behind the drawer.
When ordering parts for or making inquiries about your
range, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
on your range.
Your serial plate also tells you the rating of tile burners,
the type of fuel and tile pressure the range was adjusted
for when it left the factory.
Before You Call for Service
Read tile Before You Call for Service Checklist and
operating instructions in your Use and Care Guide. It
may save you time and expense. The list includes
common occurrences that are not the result of defective
workmanship or materials in this appliance.
Refer to the warranty in your Use and Care Guide for
our service phone number and address. Please call or
write if you have inquiries about your product and/or
need to order parts.