Check Operation - Frigidaire FGGF3685TS Installation Instructions Manual

https://appliancetechmanuals.com
36" GAS RANGE INSTALLATION INSTRUCTIONS
the flexible gas conduit at the back of the range when
replacing the unit into the cut-out opening. Replace
the drawer, close the door and switch on the electrical
power and gas to the range.

8. Check Operation

Refer to the Use and Care Guide packaged with the
range for operating instructions and for care and
cleaning of your range.
Remove all packaging from the oven before testing.
8.1 Check Operation
Do not touch the burners. They may
be hot enough to cause burns.
Install Burner Caps
This cooktop is equipped with sealed burners. All pieces
are at their place. Take note where they are. Remove
all packaging material. Make sure the burner caps are
properly aligned and leveled. The burner cap lip (See
Figure 6) should fit snug into the center of burner head
and rest level. Refer to Figures 7 & 8 for correct and
incorrect burner cap placement. Once in place, you may
check the fit by gently sliding the burner cap from side
to side (Figure 9) to be sure it is centered and firmly
seated. When the burner cap lip makes contact inside
the center of the burner head you will be able to feel it.
Please note that the burner cap should NOT move off the
center of the burner head when sliding from side to side.
NOTE: There are no burner adjustments necessary on
this cooktop.
Burner Cap
Burner Head
Correct Burner Cap
Placement - Fig. 7
Burner
Cap Lip
Fig. 6
Incorrect Burner Cap
Placement - Fig. 8
Fig. 9
8.2 Turn on Electrical Power and Open
Main Shutoff Gas Valve
8.3 Check the Igniters
Operation of electric igniters should be checked after
range and supply line connectors have been carefully
checked for leaks, and range has been connected to
electric power. To check for proper lighting:
a. Push in and turn a surface burner knob to the LITE
position. You will hear the igniter sparking.
b. The surface burner should light when gas is available
to the top burner. Each burner should light within
four (4) seconds after air has been purged from supply
lines. Visually check that burner has lit.
c. Once the burner lights, the control knob should be
rotated out of the LITE position.
There are separate ignition devices for each burner. Try
each knob separately until all burner valves have been
checked.
8.4 Adjust the "LOW" Setting of Surface
Burner Valves (see Figure 10)
a. Push in and turn each control to LITE until burner
ignites.
b. Quickly turn knob to LOWEST POSITION.
c. If burner goes out, readjust valve as follows:
Reset control to OFF. Remove the surface burner
control knob, insert a thin-bladed screw driver into the
hollow valve stem and engage the slotted screw inside.
Flame size can be increased or decreased with the
turn of the screw. Adjust flame until you can quickly
turn knob from LITE to LOWEST POSITION without
extinguishing the flame. Flame should be as small as
possible without going out.
8.5 Operation of Oven Burners and Oven
Adjustments
8.5.1 Electric Ignition Burners
Operation of electric igniters should be checked after
range and supply line connectors have been carefully
checked for leaks, and range has been connected to
electric power.
The oven burner is equipped with an electric control
system as well as an electric oven burner igniter. If your
model is equipped with a waist-high broil burner igniter,
it will also have an electric burner igniter. These control
systems require no adjustment. When the oven is set to
operate, current will flow to the igniter. It will "glow"
similar to a light bulb. When the igniter has reached
a temperature sufficient to ignite gas, the electrically
5
Figure 10