Advertisement
3-Wire
Connection
Terminal
4-Wire
Connection
Terminal
Insulated
Copper
Ground
Wire
3-Wire Copper Power Supply Cord.
To Fused Disconnect Box or Approved
Wiring Device for Copper Supply Cord.
4A. Wiring
Instructions
(3-Wire
Connection)
1. Remove the three (3) loose nuts on the terminal block using a 3/8" nut
driver or socket.
NOTE:
Do not loosen the nuts which secure the factory installed range
wiring to the terminal block. Electrical failure or loss of electrical connection
may occur if nuts are loosened.
2. Using the nuts removed in step 1, connect the cable or copper power
supply cord to the three (3) studs on the terminal block, as local codes
require. The neutral (white) wire or center wire must be connected to the
center
terminal
3. Make sure all nuts are tightened securely.
4. Replace the rear access cover.
GROUNDING
INSTRUCTIONS
- A ground link is installed on this range
which connects the center terminal of the terminal
block (neutral) to the
chassis.
The ground
link is not visible
in the picture
below
but is
connected
to the range by the center,
lowest screw (shown
in picture
ABOVE).
The ground link must not be removed
unless national or local
codes do not permit use of ground link.
NOTE:
If the ground link is removed for any reason, a separate ground
wire must be connected
to the separate
ground screw attached
to the
range chassis
and to an adequate
ground source.
4B. Wiring
Instructions
(4*Wire
Connection)
If connecting
to a 4-wire electrical
system (new branch-circuit
or
mobile home requires 4 wire connection):
1. Remove the three (3) loose nuts on the terminal block using a 3/8" nut
driver or socket. From the center stud on the terminal block, remove the
second nut and the copper ground strap. Replace the nut that held the
ground strap to the terminal block. NOTE: Do not loosen the second nut
on line 1 or line 2 which secure the factory installed range wiring to the
terminal block. Electrical failure or loss of electrical
connection
may
occur if nuts are loosened.
2. Remove the ground screw to release the copper ground strap from the
appliance.
3. Discard the ground strap. Connect the ground wire (green) of the
copper power supply cord to the frame of the appliance with the ground
screw, using the same hole in the frame where the ground strap was
removed.
4-Wire Copper Power Supply Cord.
To Fused Disconnect
Box or Approved
Wiring Device for Copper Supply Cord.
4. Using the nuts removed in step 1, connect the neutral (white) wire of
the copper power supply cord to the center silver colored stud on the
terminal block.
5. Connect the final two (2) wires to the outer studs on the terminal block.
6. Make sure all nuts are tightened securely.
7. Replace the rear access cover.
Model
and Serial
Number
Location
The serial plate location is provided in the Use & Care Manual. When
ordering parts for or making inquires about your range, always be sure to
include the model and serial numbers and a lot number or letter from the
serial plate on your range. Your serial plate also tells you the Kilowatt
rating (power requirements)
and Voltage ratings
Care,
Cleaning
and Maintenance
Refer to the Use & Care Manual for cleaning instructions.
If removing
the range is necessary
for cleaning
or maintenance,
disconnect
the
electrical
power supply.
If the electrical
supply is inaccessible,
lift the
unit slightly at the front and pull out away from the wall. Pull only as far
as necessary
to disconnect
the electrical
supply. Finish removing the
unit for servicing
and cleaning.
Reinstall in reverse order making sure
to level the range and check electrical
connections.
See pages 2 and
3 for proper anchoring
instructions.
Before
You Call for Service
Read the "Before You Calr' and operating
instruction
sections in your
Use & Care Manual. It may save you time and expense.
The list includes common
occurrences
that are not the result of
defective workmanship
or materials in this appliance.
Refer to the warranty in your Use & Care Manual for our toll-free service
number and address. Please call or write if you have inquiries about your
range product and/or need to order parts.
4
Advertisement
