Advertisement
IMPORTANT
SAFETY
INSTRUCTIONS
Ifthe information in this manual is not followed
exactly, a fire or electrical shock may result causing property
damage, personal injury or death.
• ALL RANGES
CAN TIP
• INJURYTO
PERSONS
COULD RESULT
• INSTALL ANTI-TIP
DEVICE
PACKED WITH
RANGE
• SEE INSTALLATION
INSTRUCTIONS
Important
Notes
to the Installer
1. Read all instructions
contained
in these installation
instructions
before
installing
range.
2. Remove
all packing
material
from the oven compartments
before
connecting
the gas and electrical
supply to the range.
3. Observe
all governing
codes and ordinances.
4. Be sure to leave these instructions
with the consumer.
Important
Note to the Consumer
Keep these instructions
with your owner's guide for
future reference.
As when using any appliance
generating
heat, there are certain
safety precautions
you should follow. These are listed in the
Care Manua!, read it carefully.
Be sure your range is installed and grounded
properly by a qualified
installer
or service technician.
Make sure the wall coverings
around the range can withstand
the
heat generated
by the range.
To eliminate the need to reach over the surface elements,
cabinet
storage
space above the elements
should be avoided.
BEFORE
STARTING
Tools You Will Need
For leveling
legs and Anti*Tip Bracket:
• Adjustable wrench or channel lock pliers
• 5/16" Nutdriver or Flat Head Screwdriver
• Electric Drill & 1/8" Diameter Drill Bit
(Masonry
Drill Bit if installing in concrete)
For electrical supply connection:
• 1/4" & 3/8" Socket driver or Nutdriver
Additional Materials You Will Need:
• Power Supply Cord or
• Copper Electrical Wiring & Metal Conduit
(for hard wiring)
NORMAL INSTALLATION STEPS
1.
Anti-Tip Bracket Installation Instructions-
Important
SafetyWarning
To reduce the risk of tipping of the range, the range must
be secured to the floor by properly installed anti-tip bracket
and screws packed with the range. Failure to install the
anti-tip bracket will allow the range to tip over if excessive
weight is placed on an open door or if a child climbs upon
it. Serious injury might result from spilled hot liquids or
from the range itself.
If range is ever moved to a different location, the anti-tip
brackets must also be moved and installed with the range.
Instructions are provided for installation in wood or cement
fastened to either the floor or wall. When installed to the
walt, make sure that screws completely penetrate dry wall
and are secured in wood or metal. When fastening to the
floor or wall, be sure that screws do not penetrate electrical
wiring or plumbing.
A. Locate
the Bracket
Using
the Template
-
(Bracket may be located on
either the left or right side of the
range.
Use the information
below to locate the bracket if
template is not available).
Mark the floor or wall where left or right side of the range will be
located.
If rear of range is against the wall or no further than 1-1/4"
from wall when installed,
you may use the wail or floor mount method.
If molding is installed and does not allow the bracket to fit flush against
the wall, remove molding or mount bracket to the floor. For wall mount,
locate the bracket by placing the back edge of the template against
the rear wall and the side edge of template on the mark made
referencing
the side of the range. Place bracket on top of template
and
mark location of the screw holes in wall.
if rear of range is further than
1-1/4" from the wall when installed,
attach bracket to the floor.
For
floor mount, locate the bracket by placing back edge of the template
where the rear of the range will be located.
Mark the location of the
screw holes, shown in template.
B. Drill Pilot Holes
and Fasten
Bracket
- Drill a 1/8"
pilot hole where
screws are to be
located.
If bracket is
to be mounted to the
wall, drill pilot hole at
an approximate
20 °
downward
angle.
If bracket is to be
mounted
to masonry
or ceramic
floors, drill
a 5/32" pilot hole 1-3/
4" deep. The screws
provided may be
used in wood or
concrete
material.
Use a 5/16" nut-driver
or flat head
screwdriver
to secure
the bracket in place.
FASI_N BRACKET (wNJ. o RFLOOe MOUrninG}
---_1
_--1-1/4" Max.
LevelingLeg_
_
FASTEN BRACK_'r a_LOOR M_JN11Na ONLY)
Leveling Leg --
1-1/4"
Bracket
2
Advertisement
