Advertisement
C. Level and
Position
Range
-
Level range by
adjusting
the (4)
leveling legs with a
wrench.
Note: A
minimum
clearance
of
1/8" is required
between the bottom of
the range and the
leveling leg to allow
room for the bracket.
Use a spirit level to
check
your
adjustments,
Slide
range back into
position.
(17mm)
Range Side _
_ _
Visually check that rear leveling leg is inserted into and fully secured
by the Anti-Tip
Bracket by removing lower panel or storage drawer.
For models
with a warmer drawer or broiler compartment,
grasp the
top rear edge of the range and carefully
attempt to tilt it forward.
2.
Electrical
Connection
Requirements
This appliance
must be properly installed and grounded
by a qualified
technician
in accordance
with the National Electrical Code ANSI/NFPA
No. 70-latest
edition-and
local electrical
code requirements.
This appliance
may be connected
by means of permanent
"Hard
Wiring" or "Power Supply Cord Kit."
Cover
bar
of Range
Range Connection
Opening
Size Chart
Supply Cord Kit ampere rating information.
See serial plate on range for
kilowatt rating data.
SeeSerial Plate on Rangefor
IONRating
120/240 Volts 120/208 Volts
8.8-16.5 KW
7.9-12.5 KW
16.6-22.5 KW 12.6-18.5 KW
Cord lat
Diameter (inches) of Range
Ampere
connection Opening
Rating
Permanent
CordKit
Wiring
40/50 Amp
1-3/8 in.
1-1/8 in.
50Amp
1-3/8 in.
1-3/8 in.
When hard wiring, do not leave excess wire in range compartment.
Excess
wire in the range compartment
may not allow the access
cover to be replaced properly, and could create a potential electrical
hazard if wires become pinched. Connect
only as instructed
under
"WIRING
INSTRUCTIONS"
in section 4A or 4B. When using flexible
conduit
or range cable use flex connector
or range cable strain relief.
NOTE:
Only use copper wire in connection
to terminal block.
2A. Models
with Factory
Connected
Power
Supply
Cord
NOTE:
Some models may be equipped with a factory connected
three
(3) conductor power supply cord.
Mobile home installations, new branch circuit installations (1996NEC)
or
areas where local codes do not permit grounding
through neutral require
a four (4) conductor power supply cord kit rated at 125/250 volts minimum
and marked for use with ranges. See Range Connection
Opening
Size
Chart for cord kit ampere rating information.
Terminals
on end of wires
must be either closed loop or open-end
spade lugs with upturned ends.
2B. Models Requiring Power Supply Cord Kit
RISK OF FIRE OR ELECTRICAL SHOCK MAY OCCUR IF
AN INCORRECT SIZE RANGE CORD KIT IS USED, THE
INSTALLATION INSTRUCTIONS ARE NOT FOLLOWED
OR STRAIN RELIEF BRACKET IS DISCARDED.
This appliance
may be connected
by means of a power supply cord.
Only a power supply cord kit rated at 125/250 volts minimum,
and
marked for use with ranges shah be used. See chart on page 3 for
cord kit ampere rating information.
Cord must have either three (3) or
four (4) conductors.
Terminals
on end of wires must be either dosed
loop or open-end
spade lugs with upturned
ends. Cord must have
strain relief clamp.
See section 4A for 3-wire or section 4B for 4-wire connection.
3. Electrical
Connection
to Range
The rear access cover must be removed.
To remove,
loosen center
screw (one screw)
and remove access cover. The terminal block will
then be accessible.
1-1/8" Dia.
Knockout
(See Chart)
Mountin
Plate
1-3/8" Dia, I
Hole
(See Chart)
7/8" Dia.
Hole
(See Chart)
f
Pocket
for Cable
Mounting Plate
NOTE:
Range is shipped from factory with %3/8" dia. hole as shown. To
use either 7/8" dia. hole or %1/8" dia. knockouts:
If a different
diameter
hole is required,
please follow
the steps
below:
1. Using a 1/4" socket driver, remove eight (8) screws from Rear Wall
Shield to release from the unit (as shown).
Save the screws for step
#7 below.
2. Again using the 1/4" socket driver, remove one (1) blunt point screw
used to secure the Cable Mounting Plate to the Rear Wall Shield. Save
the screws for step #6.
3. Remove the Cable Mounting
Plate from the Rear Wall Shield by
sliding the plate out of the pockets.
4. If a 1-1/8" dia. hole is required, "punch-out" the knockout.
5. Rotate the plate 180 degrees so that the desired hole is placed on
top of the opening located on the bottom flange of the Rear Wall Shield.
6. Slide the Cable Mounting Plate into the Rear Wall Shield. Re-secure
using the blunt point screw removed from step #2 above.
7. Reassemble
the Rear Wall Shield to the unit using eight (8) screws
removed
from step #1 above.
3
Advertisement
