Table of Contents
Advertisement
Available languages
Available languages
INSTALLATION
Run some water
from the hot and cold
faucets to flush the water lines and remove
particles that might clog up the water valve
screens,
Remove the inlet hoses and rubber washers
from the plastic bag and install the rubber
washers in each end of the inlet hoses.
Models equipped
with gravity
drain: Run the machine's drain
hose into an oversized floor drain or drain trough. The entire
length of the drain hose must be below the drain outlet on the
machine.
(90 ° elbow end) Carefully connect the inlet hose marked "HOT"
to the outside "H" outlet of the water valve. Tighten by hand,
then tighten another 2/3 turn with pliers. Carefully connect the
other inlet hose to the inside "C" outlet of the water valve. Tighten
by hand, then tighten another 2/3 turn with
pliers. Do not
crossthread
or over-tighten
these connections.
_
Connect the inlet hose ends to the HOT and _
"
COLD water faucets tightly by hand, then tighten
another 2/3 turn with pliers. Turn the water on T-_
and check for leaks.
I I
_
i_s,miilniO_n:i,i!_!!deot_hte_i_hrdi:innhPUsmPwl_hr_la '_L_J _ \,\_
NOTE: If the drain hose is placed in a standpipe
without
forming a U shape, a siphoning action
could occur. There must be an air gap around the
drain hose. A snug hose fit can also cause a
siphoning
action.
On machines equipped with gravity
drain, connect one end of the drain
hose
to the
drain
outlet
of the
machine, using the provided clamp.
Carefully
move the washer
to its final location.
NOTE:
Do not use the
dispenser drawer or door
to lift washer.
With the washer in its final
position, place a level on top
of the washer. Adjust the front
leveling
legs up or down to.
ensure the washer is resting
solid. Turn the lock nuts on
each leg up towards the base
of the washer and snug
with a wrench.
NOTE:
Keep the leg
extension at a minimum to
prevent excessive vibration.
The farther
out the legs are
extended the more the
washer will vibrate.
Rear leg adjustments
are also
accessible
through
the
front
service panel.
Models equipped
with drain
pump: Place the formed end of
the drain hose in a laundry tub
or a standpipe and secure with
the cable tie provided in the
enclosure package.
Cable
Tie
_Ca.ble
T,o
9,
10.
11.
NOTE: The drain pipe or floor drain, into which the drain hose is
placed, MUST be at least 1/2 inch larger in diameter
than the drain hose. This will insure that the sewer line
cannot back up into the washing machine.
8. Plug the power cord into a grounded outlet.
NOTE:
Check to ensure the power is off at the circuit breaker/
fuse box before plugging the power cord into an outlet.
Turn on the power
at the circuit
breaker/fuse
box.
Be sure you have read the "Important
Safety Instructions"
on
pages 2-3 before operating this washer.
Run the washer through a complete cycle. Check
for water leaks and proper operation.
12. Keep these instructions
for future
reference.
NOTE:
A wiring diagram is located inside the washer on the
service panel.
REPLA CEMENT
PARTS
If replacements
parts are needed
for your washer,
contact
the
source where
you purchased
your washer,
call 1-800-944-9044,
or
visit our website,
www.frigidaire.com,
for the Frigidaire
Company
Authorized
Parts Distributor
nearest
you.
_
Destroy
the carton
and
plastic
bags
after
the
washer
is unpacked.
Children
might
use them
for
play. Cartons
covered
with rugs, bedspreads,
or plastic sheets can become airtight
chambers
causing
suffocation.
Place all materials
in a garbage
container
or make materials
inaccessible
to children.
_The
instructions
in this manual and all other
literature included with this washer are not meant to cover every
possible condition and situation that may occur. Good safe practice
and caution
MUST be applied when
installing,operating
and
maintaining any appliance.
Maximum benefits and enjoyment are achieved when all the Safety
and Operating instructions
are understood
and
practiced as a
routine with your laundering tasks.
Advertisement
Table of Contents
