Download  Print this page

Mounting Plate - Frigidaire FGMV174KFA Installation Instructions Manual

Over the range
Hide thumbs

Advertisement

8
FanCover Bracket
/
/
/
/
fj
Tapping Screw
Figure 10
VEHTiLATJOH SYSTEM
(PREPARING OVENFORiNSTALLATiON)
(c)
1.
VERTICAL EXHAUST: O UTSIDE
VENTiLATiON
Remove and save 2 screws from back edge and 1 screw
from the top center of the Fan Cover Bracket. Remove
Fan Cover Bracket by sliding it in the opposite direction
of the arrow on the Fan Cover Bracket as shown in Figure
7.
2. Withdraw Hood Fan Unit carefully and slip wires out of
Wire Box. See Figure 8.
CAUTION: Do not pull or stretch hood fan wiring.
3. Turn the Hood Fan Unit end-over-end. Rotate the Hood
Fan Unit 90 ° so that the fan blade openings are facing
upward. Replace Hood Fan Unit into the oven. Be careful
not to pinch the lead wire between the inner bracket and
the Hood Fan Unit. See Figure 11.
4. Put the lead wire into Wire Box. See Figure 11.
5. Replace the Fan Cover Bracket by sliding it into the slits
in the same direction as the arrow on the Fan Cover
Bracket. Make sure the fan blades are visible through
the top openings in the oven before proceeding. Attach
the Fan Cover Bracket to unit with 3 screws, which were
removed in Step 1 above. See Figure lO.The Hood Fan
Unit is now rotated for vertical exhaust operation.
6. Attach the Exhaust Damper Assembly to the fan cover
bracket on the top of the outercase cabinet after mounting
the oven. To attach the Exhaust Damper Assembly, refer
to MOUNTING OVEN TO THE WALL, page 6 Figure 17.
Rotate90°
_/
Figure 11
90VEH
IHSTALLATiOH
THISOVENCANNOT BEPROPERLY INSTALLED WITHOUTREFERRING
TO THE MOUNTINGINSTRUCTIONS FOUNDON BOTHTEMPLATES.
THENEXTSTEPISTO READAND FOLLOW MOUNTING INFORMATION
ON BOTHTOPCABINETANDWALLTEMPLATES.
NOTE:THISOVENSHOULDBEATTACHED TO ATLEASTONE WALL
STUD.
MOUNTINGPLATE
1. Separate 4 Toggle Bolts, packed in the INSTALLATION
HARDWARE, from the Toggle Nuts.
2. _
Use
the
mounting
template
provided to Use wood screws to attach
mounting
plate to the stud or studs. UseToggie
Bolts to attach
mounting
plate through
the holes
UNLESS THOSE
HOLES
ARE LOCATED
ON THE STUD. Insert
one
Toggle
Bolt where
appropriate
(these
correspond
to
holes
of the
Wail
Template)
and put the
Toggle
Nuts
onto
the
Toggle Bolts. Figure 13.
Refer to instructions in
Wall Template.
3. Position
the
Mounting
Plate with
the Toggle
Bolts
attached
at the wall location
and insert Toggle Nuts
and Bolts through the holes in the wall with the Toggle
Nuts closed. Figure 15. Use Wood Screws to attach the
Mounting Plate to studs.
NOTE: Before insertion, be sure you leave a space more
than the thickness of the wall between the Mounting Plate
and the end of each of the Toggle Nuts (in the closed
position). If you do not leave enough space, the Toggle
Nut will not be able to open on the other side of the wall.
Also, once a Toggle Nut opens, it cannot be withdrawn
from the hole; therefore make sure all of the Toggles are
in the correct position before insertion.
4. Align the Mounting Plate carefully and hold in position
while tightening Toggle Bolts. Pull Toggle Bolt toward you
and turn clockwise to tighten. Figure 14.
E5

Hide quick links:

Advertisement

loading

  Also See for Frigidaire FGMV174KFA

  Related Manuals for Frigidaire FGMV174KFA